Datasheet

Data Sheet AD7699
Rev. B | Page 21 of 28
The register can be written to during conversion, during acquisi-
tion, or spanning acquisition/conversion and is updated at the
end of conversion, t
CONV
(maximum). There is always a one deep
delay when writing the CFG register. Note that at power-up, the
CFG register is undefined and two dummy conversions are
required to update the register. To preload the CFG register
with a factory setting, hold DIN high for two conversions. Thus
CFG[13:0] = 0x3FFF. This sets the AD7699 for the following:
 IN[7:0] unipolar referenced to GND, sequenced in order
 Full bandwidth for a one-pole filter
 Internal reference/temperature sensor disabled, buffer
enabled
 Enables the sequencer
 No readback of the CFG register
Table 8 summarizes the configuration register bit details. See
the Theory of Operation section for more details.
13 12 11 10 9 8 7 6 5 4 3 2 1 0
CFG INCC INCC INCC INx INx INx BW REF REF REF SEQ SEQ RB
Table 8. Configuration Register Description
Bit(s) Name Description
[13] CFG Configuration update.
0 = Keep current configuration settings.
1 = Overwrite contents of register.
[12:10] INCC Input channel configuration. Selection of pseudobipolar, pseudodifferential, pairs, single-ended, or temperature sensor. Refer to
the
Input Configurations section.
Bit 12 Bit 11 Bit 10 Function
0 0 X
1
Bipolar differential pairs; INx− referenced to V
REF
/2 ± 0.1 V.
0 1 0 Bipolar; INx referenced to COM = V
REF
/2 ± 0.1 V.
0 1 1 Temperature sensor.
1 0 X
1
Unipolar differential pairs; INx− referenced to GND ± 0.1 V.
1 1 0 Unipolar, IN0 to IN7 referenced to COM = GND ± 0.1 V (GND sense).
1 1 1
Unipolar, IN0 to IN7 referenced to GND.
[9:7] INx Input channel selection in binary fashion.
Bit 9 Bit 8 Bit 7 Channel
0 0 0 IN0
0 0 1 IN1
… … … …
1 1 1 IN7
[6] BW
Select bandwidth for low-pass filter. Refer to the
Selectable Low-Pass Filter section.
0 = ¼ of BW, uses an additional series resistor to further bandwidth limit the noise. Maximum throughput must also be reduced to ¼.
1 = Full BW.
[5:3] REF
Reference/buffer selection. Selection of internal, external, and external buffered references, and enabling of the on-chip
temperature sensor. Refer to the Voltage Reference Output/Input section.
Bit 5 Bit 4 Bit 3 Function
0 0 0 Not used
0 0 1
Internal reference, REF = 4.096 V output,
temperature enabled.
0 1 0 External reference, temperature enabled.
0 1 1 External reference, internal buffer, temperature enabled.
1 1 0 External reference, temperature disabled.
1 1 1 External reference, internal buffer, temperature disabled.
[2:1] SEQ Channel sequencer. Allows for scanning channels in an IN0 to IN[7:0] fashion. Refer to the Sequencer section.
Bit 2 Bit 1 Function
0 0 Disable sequencer.
0 1 Update configuration during sequence.
1 0 Scan IN0 to IN[7:0] (set in CFG[9:7]), then temperature.
1 1 Scan IN0 to IN[7:0] (set in CFG[9:7]).
0 RB Read back the CFG register.
0 = Read back current configuration at end of data.
1 = Do not read back contents of configuration.
1
X = don’t care.