Datasheet

AD7622
Rev. 0 | Page 20 of 28
Temperature Sensor
The TEMP pin measures the temperature of the AD7622. To
improve the calibration accuracy over the temperature range,
the output of the TEMP pin is applied to one of the inputs of
the analog switch (such as,
ADG779), and the ADC itself is
used to measure its own temperature. This configuration is
shown in
Figure 29.
ADG779
AD8021
C
C
ANALOG INPUT
(UNIPOLAR)
AD7622
IN+
TEMPERATURE
SENSOR
TEMP
06023-027
Figure 29. Use of the Temperature Sensor
POWER SUPPLY
The AD7622 uses three sets of power supply pins: an analog
2.5 V supply AVDD, a digital 2.5 V core supply DVDD, and a
digital input/output interface supply OVDD. The OVDD supply
allows direct interface with any logic working between 2.3 V
and 5.25 V. To reduce the number of supplies needed, the digital
core (DVDD) can be supplied through a simple RC filter from
the analog supply, as shown in
Figure 24.
Power Sequencing
The AD7622 is independent of power supply sequencing and
thus free from supply induced voltage latch-up. In addition, it is
very insensitive to power supply variations over a wide
frequency range, as shown in
Figure 30.
65.0
45.0
1 10000
FREQUENCY (kHz)
PSRR (dB)
10 100 1000
47.5
50.0
52.5
55.0
57.5
60.0
62.5
06023-029
EXT REF
INT REF
Figure 30. PSRR vs. Frequency
Power-Up
At power-up, or when returning to operational mode from the
power-down mode (PD = high), the AD7622 engages an
initialization process. During this time, the first 128 conversions
should be ignored or the RESET input could be pulsed to
engage a faster initialization process. Refer to the
Digital
Interface
section for RESET and timing details.
A simple power-on reset circuit, as shown in
Figure 24, can be
used to minimize the digital interface. As OVDD powers up, the
capacitor is shorted and brings RESET high; it is then charged
returning RESET to low. However, this circuit only works when
powering up the AD7622 because the power-down mode
(PD = high) does not power down any of the supplies and as a
result, RESET is low.
It should be noted that the digital interface remains active even
during the acquisition phase. To reduce the operating digital
supply currents even further, drive the digital inputs close to
the power rails (that is, OVDD and OGND).
CONVERSION CONTROL
The AD7622 is controlled by the
CNVST
input. A falling edge
on
CNVST
is all that is necessary to initiate a conversion.
Detailed timing diagrams of the conversion process are shown
in
Figure 31. Once initiated, it cannot be restarted or aborted,
even by the power-down input, PD, until the conversion is
complete. The
CNVST
signal operates independently of
CS
and
RD
signals.
BUSY
MODE
CONVERT ACQUIREACQUIRE CONVERT
CNVST
t
1
t
2
t
4
t
3
t
5
t
6
t
7
t
8
06023-030
Figure 31. Basic Conversion Timing
For optimal performance, the rising edge of
CNVST
should not
occur after the maximum
CNVST
low time, t
1
, or until the end
of conversion.
Although
CNVST
is a digital signal, it should be designed with
special care with fast, clean edges and levels with minimum
overshoot and undershoot or ringing.
The
CNVST
trace should be shielded with ground and a low
value serial resistor (for example, 50 Ω) termination should be
added close to the output of the component that drives this line.
In addition, a 50 pF capacitor is recommended to further reduce
the effects of overshoot and undershoot as shown in
Figure 24.
For applications where SNR is critical, the
CNVST
signal should
have very low jitter. This can be achieved by using a dedicated
oscillator for
CNVST
generation, or by clocking
CNVST
with a
high frequency, low jitter clock, as shown in
Figure 24.