Datasheet

Data Sheet AD7327
Rev. B | Page 7 of 36
TIMING SPECIFICATIONS
V
DD
= 12 V to 16.5 V, V
SS
= −12 V to −16.5 V, V
CC
= 2.7 V to 5.25 V, V
DRIVE
= 2.7 V to 5.25 V, V
REF
= 2.5 V to 3.0 V internal/external,
T
A
= T
MAX
to T
MIN
. Timing specifications apply with a 32 pF load, unless otherwise noted.
1
Table 3.
Limit at T
MIN
, T
MAX
Description
Parameter V
CC
< 4.75 V V
CC
= 4.75 V to 5.25 V Unit V
DRIVE
≤ V
CC
f
SCLK
50
50
kHz min
10 10 MHz max
t
CONVERT
16 × t
SCLK
16 × t
SCLK
ns max t
SCLK
= 1/f
SCLK
t
QUIET
75 60 ns min
Minimum time between end of serial read and next falling edge of
CS
t
1
12 5 ns min
Minimum
CS pulse width
t
2
2
25
20
ns min
CS to SCLK set-up time; bipolar input ranges (±10 V, ±5 V, ±2.5 V)
45 35 ns min Unipolar input range (0 V to 10 V)
t
3
26 14 ns max
Delay from
CS until DOUT three-state disabled
t
4
57 43 ns max Data access time after SCLK falling edge
t
5
0.4 × t
SCLK
0.4 × t
SCLK
ns min SCLK low pulse width
t
6
0.4 × t
SCLK
0.4 × t
SCLK
ns min SCLK high pulse width
t
7
13
8
ns min
SCLK to data valid hold time
t
8
40 22 ns max SCLK falling edge to DOUT high impedance
10 9 ns min SCLK falling edge to DOUT high impedance
t
9
4 4 ns min DIN set-up time prior to SCLK falling edge
t
10
2 2 ns min DIN hold time after SCLK falling edge
t
POWER-UP
750 750 ns max Power-up from autostandby
500 500 µs max
Power-up from full shutdown/autoshutdown mode, internal
reference
25 25 µs typ
Power-up from full shutdown/autoshutdown mode, external
reference
1
Sample tested during initial release to ensure compliance. All input signals are specified with tr = tf = 5 ns (10% to 90% of V
DRIVE
) and timed from a voltage level of 1.6 V.
2
When using the 0 V to 10 V unipolar range, running at 500 kSPS throughput rate with t
2
at 20 ns, the mark space ratio needs to be limited to 50:50.
ADD1
1 2 3
4 5
13
14 15
16
WR
ITE
REG
SEL1
REG
SE
L2
LSB
MSB
ADD0
SIG
N DB
11 DB1
0 DB
2 DB1
DB0
t
2
t
6
t
4
t
9
t
10
t
3
t
7
t
5
t
8
t
1
t
QU
IET
t
C
ON
VER
T
SC
LK
CS
DO
UT
THR
EE-
ST
ATE
THR
EE-STA
TE
D
IN
ADD2
3 IDENTIFI
CAT
ION B
ITS
05401-002
D
ON’
T
CARE
Figure 2. Serial Interface Timing Diagram