Datasheet

Data Sheet AD7321
Rev. B | Page 29 of 36
AUTOSHUTDOWN MODE
(PM1 = 1, PM0 = 0)
Once the autoshutdown mode is selected, the AD7321 auto-
matically enters shutdown on the 15
th
SCLK rising edge. In
autoshutdown mode, all internal circuitry is powered down.
The AD7321 retains information in the registers during
autoshutdown. The track-and-hold is in hold mode during
autoshutdown. On the rising
CS
edge, the track-and-hold,
which was in hold during shutdown, returns to track as the
AD7321 begins to power up. The power-up from autoshutdown
is 500 µs.
When the control register is programmed to transition to
autoshutdown mode, it does so on the 15
th
SCLK rising edge.
Figure 47 shows the part entering autoshutdown mode. The
AD7321 automatically begins to power up on the
CS
rising
edge. The t
POWER-UP
is required before a valid conversion, initiated
by bringing the
CS
signal low, can take place. Once this valid
conversion is complete, the AD7321 powers down again on the
15
th
SCLK rising edge. The
CS
signal must remain low again to
keep the part in autoshutdown mode.
AUTOSTANDBY MODE
(PM1 = 0, PM0 =1)
In autostandby mode, portions of the AD7321 are powered
down, but the on-chip reference remains powered up. The
reference bit in the control register should be 1 to ensure that
the on-chip reference is enabled. This mode is similar to
autoshutdown but allows the AD7321 to power up much faster,
which allows faster throughput rates.
As is the case with autoshutdown mode, the AD7321 enters
standby on the 15
th
SCLK rising edge once the control register
is updated (see Figure 47). The part retains information in the
registers during standby. The AD7321 remains in standby until
it receives a
CS
rising edge. The ADC begins to power up on the
CS
rising edge. On the
CS
rising edge, the track-and-hold, which
was in hold mode while the part was in standby, returns to track.
The power-up time from standby is 700 ns. The user should
ensure that 700 ns have elapsed before bringing
CS
low to
attempt a valid conversion. Once this valid conversion is
complete, the AD7321 again returns to standby on the 15
th
SCLK rising edge. The
CS
signal must remain low to keep the
part in standby mode.
Figure 47 shows the part entering autoshutdown mode. The
sequence of events is the same when entering autostandby
mode. In Figure 47, the power management bits are configured
for autoshutdown. For autostandby mode, the power
management bits, PM1 and PM0, should be set to 0 and 1,
respectively.
CS
1
1615 1 1
61
5
SCL
K
SDATA
DIN
VAL
ID D
ATA V
ALI
D DATA
DATA I
NTO C
ONT
ROL R
EGISTER DATA
INT
O CO
NTRO
L REGISTER
t
POWER-UP
C
ONT
ROL R
EGISTER IS LO
ADED O
N TH
E FIRST 15 CLO
CKS,
PM1 = 1, PM0 = 0
PAR
T E
NT
E
RS
S
HUT
DO
WN MODE
ON TH
E 15T
H R
IS
I
NG
SC
L
K E
D
GE
AS PM1 = 1, PM0
= 0
PAR
T BEGINS TO POWER
U
P
ON
C
S R
IS
I
NG
ED
G
E
THE
P
ART
IS
F
UL
L
Y P
OW
ER
ED UP
ONC
E
t
POWER-UP
HAS ELAPSED
05399-042
Figure 47. Entering Autoshutdown/Autostandby Mode
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.