Datasheet

REV. E
–2–
AD711–SPECIFICATIONS
(V
S
= 15 V @ T
A
= 25C, unless otherwise noted.)
J/A/S K/B/T C
Parameter Min Typ Max Min Typ Max Min Typ Max Unit
INPUT OFFSET VOLTAGE
1
Initial Offset 0.3 2/1/1 0.2 0.5 0.10 0.25 mV
T
MIN
to T
MAX
3/2/2 1.0 0.45 mV
vs. Temp 7 20/20/20 5 10 2 5 mV/∞C
vs. Supply 76 95 80 100 86 110 dB
T
MIN
to T
MAX
76/76/76 80 86 dB
Long-Term Stability 15 15 15 mV/Month
INPUT BIAS CURRENT
2
V
CM
= 0 V 15 50 15 50 15 25 pA
V
CM
= 0 V @ T
MAX
1.1/3.2/51 1.1/3.2/51 1.6 nA
V
CM
= ±10 V 20 100 20 100 20 50 pA
INPUT OFFSET CURRENT
V
CM
= 0 V 10 25 5 25 5 10 pA
V
CM
= 0 V @ T
MAX
0.6/1.6/26 0.6/1.6/26 0.65 nA
FREQUENCY RESPONSE
Small Signal Bandwidth 3.0 4.0 3.4 4.0 3.4 4.0 MHz
Full Power Response 200 200 200 kHz
Slew Rate 16 20 18 20 18 20 V/ms
Settling Time to 0.01% 1.0 1.2 1.0 1.2 1.0 1.2 ms
Total Harmonic Distortion 0.0003 0.0003 0.0003 %
INPUT IMPEDANCE
Differential 3 ¥ 10
12
储5.5 3 ¥ 10
12
储5.5 3 ¥ 10
12
储5.5 W储pF
Common Mode 3 ¥ 10
12
储5.5 3 ¥ 10
12
储5.5 3 ¥ 10
12
储5.5 W储pF
INPUT VOLTAGE RANGE
Differential
3
±20 ±20 ±20 V
Common-Mode Voltage
4
+14.5, –11.5 +14.5, –11.5 +14.5, –11.5
T
MIN
to T
MAX
–V
S
+ 4 +V
S
– 2 –V
S
+ 4 +V
S
– 2 –V
S
+ 4 +V – 2 V
Common-Mode
Rejection Ratio
V
CM
= ±10 V 76 88 80 888694dB
T
MIN
to T
MAX
76/76/76 84 80 84 86 90 dB
V
CM
= ±11 V 70 84 76 847690dB
T
MIN
to T
MAX
70/70/70 80 74 80 74 84 dB
INPUT VOLTAGE NOISE 2 2 2 4 mV p-p
45 45 45 nV/÷Hz
22 22 22 nV/÷Hz
18 18 18 nV/÷Hz
16 16 16 nV/÷Hz
INPUT CURRENT NOISE 0.01 0.01 0.01 pA/÷Hz
OPEN-LOOP GAIN 150 400 200 400 200 400 V/mV
100/100/100 100 100 V/mV
OUTPUT
CHARACTERISTICS
Voltage +13, –12.5 +13.9, –13.3 +13, –12.5 +13.9, –13.3 +13, –12.5 +13.9, –13.3 V
±12/±12/±12 +13.8, –13.1 ±12 +13.8, –13.1 ±12 +13.8, –13.1 V
Current 25 25 25 mA
POWER SUPPLY
Rated Performance ±15 ±15 ±15 V
Operating Range ± 4.5 ± 18 ±4.5 ±18 ±4.5 ±18 V
Quiescent Current 2.5 3.4 2.5 3.0 2.5 2.8 mA
NOTES
1
Input Offset Voltage specifications are guaranteed after 5 minutes of operation at T
A
= 25∞C.
2
Bias Current specifications are guaranteed maximum at either input after 5 minutes of operation at T
A
= 25∞C. For higher temperatures, the current doubles every 10∞C.
3
Defined as voltage between inputs, such that neither exceeds ± 10 V from ground.
4
Typically exceeding –14.1 V negative common-mode voltage on either input results in an output phase reversal.
Specifications subject to change without notice.