Datasheet

REV. E
–2–
AD633–SPECIFICATIONS
(T
A
= 25ⴗC, V
S
= ⴞ15 V, R
L
≥ 2 k⍀)
Model AD633J, AD633A
W
XXYY
V
Z=
−
( )
−
( )
+
1212
10
TRANSFER FUNCTION
Parameter Conditions Min Typ Max Unit
MULTIPLIER PERFORMANCE
Total Error –10 V ≤ X, Y ≤ +10 V ±1
ⴞ 2 % Full Scale
T
MIN
to T
MAX
±3% Full Scale
Scale Voltage Error SF = 10.00 V Nominal ±0.25% % Full Scale
Supply Rejection V
S
= ±14 V to ±16 V ±0.01 % Full Scale
Nonlinearity, X X = ±10 V, Y = +10 V ±0.4
ⴞ 1 % Full Scale
Nonlinearity, Y Y = ± 10 V, X = +10 V ±0.1
ⴞ 0.4 % Full Scale
X Feedthrough Y Nulled, X = ±10 V ±0.3
ⴞ 1 % Full Scale
Y Feedthrough X Nulled, Y = ±10 V ±0.1
ⴞ 0.4 % Full Scale
Output Offset Voltage ±5 ⴞ 50 mV
DYNAMICS
Small Signal BW V
O
= 0.1 V rms 1 MHz
Slew Rate V
O
= 20 V p-p 20 V/µs
Settling Time to 1% ∆ V
O
= 20 V 2 µs
OUTPUT NOISE
Spectral Density 0.8 µV/√Hz
Wideband Noise f = 10 Hz to 5 MHz 1 mV rms
f = 10 Hz to 10 kHz 90 µV rms
OUTPUT
Output Voltage Swing
ⴞ 11 V
Short Circuit Current R
L
= 0 Ω 30 40 mA
INPUT AMPLIFIERS
Signal Voltage Range Differential
ⴞ 10 V
Common Mode
ⴞ 10 V
Offset Voltage X, Y ±5
ⴞ 30 mV
CMRR X, Y V
CM
= ±10 V, f = 50 Hz 60 80 dB
Bias Current X, Y, Z 0.8 2.0 µA
Differential Resistance 10 MΩ
POWER SUPPLY
Supply Voltage
Rated Performance ±15 V
Operating Range
ⴞ 8 ⴞ 18 V
Supply Current Quiescent 4 6 mA
Specifications shown in boldface are tested on all production units at electrical test. Results from those tests are used to calculate outgoing quality levels. All min and
max specifications are guaranteed, although only those shown in boldface are tested on all production units.
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS
1
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±18 V
Internal Power Dissipation
2
. . . . . . . . . . . . . . . . . . . 500 mW
Input Voltages
3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±18 V
Output Short Circuit Duration . . . . . . . . . . . . . . . . Indefinite
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Operating Temperature Range
AD633J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
AD633A . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
Lead Temperature Range (Soldering 60 sec) . . . . . . . . . 300°C
ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000 V
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent
damage to the device. This is a stress rating only; functional operation of the device at
these or any other conditions above those indicated in the operational section of this
specification is not implied.
2
8-Lead Plastic DIP Package: θ
JA
= 90°C/W; 8-Lead Small Outline Package: θ
JA
=
155°C/W.
3
For supply voltages less than ±18 V, the absolute maximum input voltage is equal to
the supply voltage.
ORDERING GUIDE
Temperature Package Package
Model Range Description Option
AD633AN –40°C to +85°C Plastic DIP N-8
AD633AR –40°C to +85°C Plastic SOIC RN-8
AD633AR-REEL –40°C to +85°C 13" Tape and Reel RN-8
AD633AR-REEL7 –40°C to +85°C 7" Tape and Reel RN-8
AD633JN 0°C to 70°C Plastic DIP N-8
AD633JR 0°C to 70°C Plastic SOIC RN-8
AD633JR-REEL 0°C to 70°C 13" Tape and Reel RN-8
AD633JR-REEL7 0°C to 70°C 7" Tape and Reel RN-8