Datasheet

REV. 0
–2–
AD5334/AD5335/AD5336/AD5344–SPECIFICATIONS
(V
DD
= 2.5 V to 5.5 V, V
REF
= 2 V. R
L
= 2 k⍀ to GND; C
L
=200 pF to GND; all specifications T
MIN
to T
MAX
unless otherwise noted.)
B Version
2
Parameter
1
Min Typ Max Unit Conditions/Comments
DC PERFORMANCE
3, 4
AD5334
Resolution 8 Bits
Relative Accuracy ± 0.15 ± 1 LSB
Differential Nonlinearity ± 0.02 ± 0.25 LSB Guaranteed Monotonic By Design Over All Codes
AD5335/AD5336
Resolution 10 Bits
Relative Accuracy ± 0.5 ± 4 LSB
Differential Nonlinearity ± 0.05 ± 0.5 LSB Guaranteed Monotonic By Design Over All Codes
AD5344
Resolution 12 Bits
Relative Accuracy ± 2 ± 16 LSB
Differential Nonlinearity ± 0.2 ± 1 LSB Guaranteed Monotonic By Design Over All Codes
Offset Error ± 0.4 ± 3 % of FSR
Gain Error ± 0.1 ± 1 % of FSR
Lower Deadband
5
10 60 mV Lower Deadband Exists Only if Offset Error Is Negative
Upper Deadband 10 60 mV V
DD
= 5 V. Upper Deadband Exists Only if V
REF =
V
DD
Offset Error Drift
6
–12 ppm of FSR/°C
Gain Error Drift
6
–5 ppm of FSR/°C
DC Power Supply Rejection Ratio
6
–60 dB ∆V
DD
= ±10%
DC Crosstalk
6
200 µVR
L
= 2 kΩ to GND, 2 kΩ to V
DD
; C
L
= 200 pF to GND;
Gain = 0
DAC REFERENCE INPUT
6
V
REF
Input Range 0.25 V
DD
V
V
REF
Input Impedance 180 kΩ Gain = 1. Input Impedance = R
DAC
(AD5336/AD5344)
90 kΩ Gain = 2. Input Impedance = R
DAC
(AD5336)
90 kΩ Gain = 1. Input Impedance = R
DAC
(AD5334/AD5335)
45 kΩ Gain = 2. Input Impedance = R
DAC
(AD5334)
Reference Feedthrough –90 dB Frequency = 10 kHz
Channel-to-Channel Isolation –90 dB Frequency = 10 kHz
OUTPUT CHARACTERISTICS
6
Minimum Output Voltage
4, 7
0.001 V min Rail-to-Rail Operation
Maximum Output Voltage
4, 7
V
DD
– 0.001 V max
DC Output Impedance 0.5 Ω
Short Circuit Current 50 mA V
DD
= 5 V
20 mA V
DD
= 3 V
Power-Up Time 2.5 µs Coming Out of Power-Down Mode. V
DD
= 5 V
5 µs Coming Out of Power-Down Mode. V
DD
= 3 V
LOGIC INPUTS
6
Input Current ± 1 µA
V
IL
, Input Low Voltage 0.8 V V
DD
= 5 V ± 10%
0.6 V V
DD
= 3 V ± 10%
0.5 V V
DD
= 2.5 V
V
IH
, Input High Voltage 2.4 V V
DD
= 5 V ± 10%
2.1 V V
DD
= 3 V ± 10%
2.0 V V
DD
= 2.5 V
Pin Capacitance 3.5 pF
POWER REQUIREMENTS
V
DD
2.5 5.5 V
I
DD
(Normal Mode) All DACs active and excluding load currents.
V
DD
= 4.5 V to 5.5 V 600 900 µAV
IH
= V
DD
, V
IL
= GND.
V
DD
= 2.5 V to 3.6 V 500 700 µAI
DD
increases by 50 µA at V
REF
> V
DD
– 100 mV.
I
DD
(Power-Down Mode)
V
DD
= 4.5 V to 5.5 V 0.2 1 µA
V
DD
= 2.5 V to 3.6 V 0.08 1 µA
NOTES
1
See Terminology section.
2
Temperature range: B Version: –40°C to +105°C; typical specifications are at 25°C.
3
Linearity is tested using a reduced code range: AD5334 (Code 8 to 255); AD5335/AD5336 (Code 28 to 1023); AD5344 (Code 115 to 4095).
4
DC specifications tested with outputs unloaded.
5
This corresponds to x codes. x = Deadband voltage/LSB size.
6
Guaranteed by design and characterization, not production tested.
7
In order for the amplifier output to reach its minimum voltage, Offset Error must be negative. In order for the amplifier output to reach its maximum voltage, V
REF
= V
DD
and
“Offset plus Gain” Error must be positive.
Specifications subject to change without notice.