PanelView Standard Operator Terminals User Manual (Catalog Numbers PV300 Micro, PV300, PV550, PV600, PV900, PV1000, PV1400)
Important User Information Solid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (publication SGI-1.1 available from your local Rockwell Automation sales office or online at http://literature.rockwellautomation.com) describes some important differences between solid state equipment and hard-wired electromechanical devices.
Summary of Changes The information below summarizes the changes to this manual since the last publication. To help you find new and updated information in this release of the manual, we have included change bars as shown to the right of this paragraph. 3Publication 2711-UM014G-EN-P - September 2008 Topic Page Updated list of supported memory cards. 105 Added information on the proper placement of the sealing gasket.
Summary of Changes 4 Publication 2711-UM014G-EN-P - September 2008
Table of Contents Preface Objectives. . . . . . . . . . . . . . . . . . . . . . Intended Audience . . . . . . . . . . . . . . . Conventions . . . . . . . . . . . . . . . . . . . . Terminology . . . . . . . . . . . . . . . . . . . . Installing PanelView Terminals . . . . . . European Union Directive Compliance Additional Resources. . . . . . . . . . . . . . Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . Touch Screen Operation . . . . . . . . . . . . . . . Keypad Operation . . . . . . . . . . . . . . . . . . . . Configuration Mode Menu . . . . . . . . . . . . . . . . . Terminal Messages . . . . . . . . . . . . . . . . . . . . . . Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Alarm List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accessories . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Select a Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Language List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Use a Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . Memory Card Listing . . . . . . . . . . . . . . . . . . . . . . . . . Disconnect Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . Applications on Card . . . . . . . . . . .
Table of Contents Set Up the Printer . . . . . . . . . . Handshaking . . . . . . . . . . . Communication Parameters Baud Rate . . . . . . . . . . . . . Top of Form . . . . . . . . . . . Port Mode . . . . . . . . . . . . . Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Multistate Indicators . . Bar Graph Displays . . . Analog Gauges . . . . . . Numeric Data Displays Message Displays . . . . Time or Date . . . . . . . Printing . . . . . . . . . . . Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Chapter 9 Installing the PV600 Terminal Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hazardous Location Considerations . . . . . . . . . . . . . . . . Enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . PV600 Keypad, Keypad and Touch Screen Terminals PV600 Touch Screen Terminals. . . .
Table of Contents Install the PV1400 Terminal in a Panel . . . . . . . . . . . . . . . . 173 Mount Terminal with Mounting Studs . . . . . . . . . . . . . . 175 Chapter 12 Terminal Connections Publication 2711-UM014G-EN-P - September 2008 Chapter Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wiring and Safety Guidelines. . . . . . . . . . . . . . . . . . . . . . . Cable Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents ControlNet Connections . . . . . . . . . . . . . . . . . . . . . . . . . . Related Information . . . . . . . . . . . . . . . . . . . . . . . . . . . ControlNet Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . Compatible ControlNet Controllers . . . . . . . . . . . . . . . . ControlNet Terminal Ports . . . . . . . . . . . . . . . . . . . . . . Typical ControlNet Network . . . . . . . . . . . . . . . . . . . . . Making ControlNet Connections . . . . . . . . . . . . . . . . . .
Table of Contents PanelView 900 Monochrome and Color Terminals PanelView 1000 Color & Grayscale . . . . . . . . . . . PanelView 1400 Color . . . . . . . . . . . . . . . . . . . . . Communication. . . . . . . . . . . . . . . . . . . . . . . . . . Agency Certifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240 244 245 247 248 Appendix B Messages, Codes and Self-test Numbers Types of Terminal Messages . . . . .
Table of Contents 14 Publication 2711-UM014G-EN-P - September 2008
Preface Objectives Read this preface to familiarize yourself with the rest of this manual. • • • • • • • Intended Audience Intended audience Conventions used Terminology Installing PanelView terminals European Union Directive Compliance Related publications Technical support No special knowledge is required to understand this manual or operate the PanelView terminals. Before running an application, you must know the functions of all screens and screen objects.
Preface Additional Resources Refer to the extensive online help for the PanelBuilder32 Software or the following publications if necessary.
Chapter 1 Terminal Overview Chapter Objectives This chapter gives an overview of the PanelView Operator Terminals. • Intended uses • Terminal types and features • Applications • Configuration mode • Terminal messages • Printing • Accessories and replacement parts Intended Uses You can use the PanelView operator terminals for a wide variety of machine control and monitoring applications.
Chapter 1 Terminal Overview Color and Grayscale Terminals Color terminals support a fixed palette of 32 standard EGA colors. Grayscale terminals support a fixed palette of four colors (shades of gray). All color in an application is defined when the application is created. Colors are not selectable at the terminal. PanelView 300 Monochrome Terminals The PanelView 300 terminal is only available with 24V DC input power.
Terminal Overview Chapter 1 PanelView 550 Monochrome Terminals The touch screen version of the PanelView 550 terminal is available only with 24V DC power. The L1 in the catalog number indicates DC power.
Chapter 1 Terminal Overview PanelView 600 Color Terminals Operator Input Touch Screen and Keypad Communication Port RIO DH-485 RS-232 DH+ (DH-485) DeviceNet ControlNet RS-232 Ethernet (DF1) x Printer Port RS-232 Catalog Number(1) x 2711-B6C1 x 2711-B6C2 x x x 2711-B6C5 x x x x x x Keypad x x 2711-B6C8 x 2711-B6C9 x 2711-B6C10 x 2711-B6C15 x 2711-B6C16 x 2711-B6C20 x 2711-K6C1 x 2711-K6C2 x x x x x x x x x x 2711-K6C8 x 2711-K6C9 x 2711-K6C10 x 2711-K6C15 x 27
Terminal Overview Chapter 1 PanelView 900 Monochrome Terminals These terminals are no longer available for purchase.
Chapter 1 Terminal Overview PanelView 900 Color Terminals These terminals are no longer available for purchase.
Terminal Overview Chapter 1 PanelView 1000 Color Terminals Operator Input Touch Screen Communication Port RIO DH-485 RS-232 DH+ (DH-485) DeviceNet ControlNet Printer Port RS-232 Ethernet RS-232 (DF1) x x x x x x x x Keypad x x x x x x x x (1) Catalog Number(1) x 2711-T10C1 x 2711-T10C3 x 2711-T10C8 x 2711-T10C9 x 2711-T10C10 x 2711-T10C15 x 2711-T10C16 x 2711-T10C20 x 2711-K10C1 x 2711-K10C3 x 2711-K10C8 x 2711-K10C9 x 2711-K10C10 x 2711-K10C15 x 2711-K10C16 x 2711
Chapter 1 Terminal Overview PanelView 1000 Grayscale Terminals Operator Input Touch Screen Communication Port RIO DH-485 RS-232 (DH-485) DH+ Printer Port DeviceNet ControlNet RS-232 Ethernet RS-232 (DF1) x x x x x x x x Keypad x x x x x x x x (1) 24 Catalog Number(1) x 2711-T10G1 x 2711-T10G3 x 2711-T10G8 x 2711-T10G9 x 2711-T10G10 x 2711-T10G15 x 2711-T10G16 x 2711-T10G20 x 2711-K10G1 x 2711-K10G3 x 2711-K10G8 x 2711-K10G9 x 2711-K10G10 x 2711-K10G15 x 2711-K10G16
Terminal Overview Chapter 1 PanelView 1400 Color Terminals These terminals are no longer available for purchase.
Chapter 1 Terminal Overview PanelView 300 Micro Terminal Features This section defines features of the PanelView 300 Micro keypad terminal. PanelView 300 Micro Terminal Features (front) 4 2 2 1 3 # Feature Description 1 Function keys (F1…F4) Use the function keys to initiate functions on the terminal display.
Terminal Overview PanelView 300 Terminal Features Chapter 1 This section defines features of the PanelView 300 keypad terminal. PanelView 300 Terminal Features (front) 5 4 1 2 3 # Feature Description 1 Function keys (F1…F8) Use the function keys to initiate functions on the terminal display. These keys may have custom legends. 2 Cursor keys Use the up or down cursor keys to move the cursor up or down in a list or to increment/decrement values.
Chapter 1 Terminal Overview PanelView 300 Terminal Features (back) DeviceNet with additional RS-232 Port 3 4 RS-232 (DH-485 or DF1) without additional RS-232 Port 5 10 12 9 or 11 2 DH-485 without RS-232 Port 6 1 8 7 7, 8, 9, 10, 11, 12 # Feature Description 1 Nameplate label Provides product information. 2 Sealing gasket Seals the front of the terminal to an enclosure or panel. 3 COMM Status indicator (green) Indicates when communication is occurring.
Terminal Overview PanelView 550 Terminal Features Chapter 1 This section defines features of the PanelView 550 terminals. PanelView 550 Terminal Features (front) Keypad Terminal Keypad & Touch Screen Terminal Cell 16 Cell 1 5 4 3 6 Cell 113 1 Cell 128 2 Touch Screen Terminal Cell 1 Cell 16 5 6 Cell 113 Cell 128 # Feature Description 1 Function Keys (F1…F10) On keypad terminals, use the function keys to initiate functions on the terminal display. These keys may have custom legends.
Chapter 1 Terminal Overview PanelView 550 Keypad or Keypad and Touch Screen Terminals (back) DH-485 without additional RS-232 Port 4 5 3 2 6 1 7 AC connector shown, DC connector looks different 11 10 8 DH-485 with additional RS-232 Port 19 11 10 RS-232 (DH-485) without additional RS-232 Port 12 9 Backlight lamp behind access cover Series G and earlier Remote I/O, DF1, DH+, DeviceNet, ControlNet, Ethernet, with additional RS-232 Port 13, 14, 15, 16, 17, or 18 19 RS-232 (DH-485) with additio
Terminal Overview Chapter 1 # Feature Description 1 Power Connection Terminals Connects to external power source. 2 Nameplate Label Provides product information. 3 Sealing Gasket Seals the front of the terminal to an enclosure or panel. 4 COMM Status (Green) Indicator Indicates when communication is occurring. 5 FAULT Status (Red) Indicator Indicates firmware or hardware faults. 6 Memory Card Slot Accepts a memory card which stores applications.
Chapter 1 Terminal Overview PanelView 550 Touch Screen Terminal Features (back) DH-485 without additional RS-232 Port 5 4 6 3 2 7 1 11 DH-485 with RS-232 Port 10 9 8 Backlight lamp behind access cover Series A only 9 11 10 19 RS-232 (DH-485) without additional RS-232 Port Remote I/O, DF1, DH+, DeviceNet, ControlNet, Ethernet, with RS-232 Port 12 RS-232 (DH-485) with additional RS-232 Port 19 12 32 13, 14, 15, 16, 17, or 18 19 Publication 2711-UM014G-EN-P - September 2008
Terminal Overview Chapter 1 # Feature Description 1 Power Connection Terminals Connects to external DC power source. 2 Sealing Gasket Seals the front of the terminal to an enclosure or panel. 3 FAULT Status (Red) Indicator Indicates firmware or hardware faults. 4 COMM Status (Green) Indicator Indicates when communication is occurring. 5 Nameplate Label Provides product information. 6 Memory Card Slot Accepts a memory card which stores applications.
Chapter 1 Terminal Overview PanelView 600 Terminal Features This section defines features of the PanelView 600 terminals.
Terminal Overview Chapter 1 # Feature Description 1 Function Keys (F1…F10) Use the function keys on keypad terminals to initiate functions on the terminal display. These keys may have custom legends. On the keypad & touch screen terminals, you can initiate functions by using the function keys and/or touch screen objects. 2 Cursor Keys Use the cursor keys to move the cursor in displayed lists, to select a numeric entry object, or to enter configuration mode.
Chapter 1 Terminal Overview PanelView 600 Keypad or Keypad & Touch Screen Terminal (back) Remote I/O, DF1, DH+, DeviceNet, ControlNet, or Ethernet with additional RS-232 Port 4 10, 11, 12, 13, 14, or 15 16 DH-485 without additional RS-232 Port 3 2 7 8 1 7, 8, 9, 10 11, 12, 13, 14, 15, 16 6 DH-485 with additional RS-232 Port 16 7 8 RS-232 (DH-485) without additional RS-232 Port 9 36 5 RS-232 (DH-485) with additional RS-232 Port 16 9 Publication 2711-UM014G-EN-P - September 2008
Terminal Overview Chapter 1 # Feature Description 1 Power Connection Terminals Connects to external power source. 2 Nameplate Label Provides product information. 3 Memory Card Slot Accepts a memory card which stores applications. 4 Sealing Gasket Seals the front of the terminal to an enclosure or panel. 5 FAULT Status (Red) Indicator Indicates firmware or hardware faults. 6 COMM Status (Green) Indicator Indicates when communication is occurring.
Chapter 1 Terminal Overview PanelView 600 Touch Screen Terminal Features (back) Remote I/O, DF1, DH+, DeviceNet, ControlNet, or Ethernet with additional RS-232 Port 5 11, 12, 13, 14, 15, or 16 17 4 3 DH-485 without additional RS-232 Port 2 1 8 9 8, 9, 10, 11 12, 13, 14, 15, 16, 17 7 6 DH-485 with additional RS-232 Port 17 8 9 RS-232 (DH-485) without additional RS-232 Port 10 38 RS-232 (DH-485) with additional RS-232 Port 17 10 Publication 2711-UM014G-EN-P - September 2008
Terminal Overview Chapter 1 # Feature Description 1 Power Connection Terminals Connects to external power source. 2 Nameplate Label Provides product information. 3 Fault Status (Red) Indicates firmware or hardware faults. 4 COMM Status (Green) Indicates when communication is occurring. 5 Sealing Gasket Seals the front of the terminal to an enclosure or panel. 6 Reset Button Resets the terminal. 7 Memory Card Slot Accepts a memory card which stores applications.
Chapter 1 Terminal Overview PanelView 900/1000 Terminal Features This section defines features of the PanelView 900 and 1000 terminals. IMPORTANT PanelView 900 terminals are no longer available. Contact your local sales office or authorized Rockwell Automation Distributor for suitable substitutes.
Terminal Overview Chapter 1 # Feature Description 1 Function Keys (F1…F16) Use the function keys on keypad terminals to initiate functions on the terminal display. These keys may have custom legends. 2 Cursor Keys Use the cursor keys to move the cursor in displayed lists, to select a numeric entry object or to enter configuration mode. 3 Numeric Entry Keys 0…9 - Enters numeric values. . Enters a decimal point. - Enters a negative value. ←Clears entered digits or cancels the scratchpad.
Chapter 1 Terminal Overview PanelView 900/1000 Terminal Features (back) Remote I/O, DF1, DH+, DeviceNet, Ethernet, or ControlNet with additional RS-232 Port 4 Back View Touch Screen Terminal 3 11, 12, 13, 14, 15, or 16 17 5 2 DH-485 Version without additional RS-232 Port 6 1 8 9 8, 9, 10 11, 12, 13, 14, 15, 16, 17 7 DH-485 with additional RS-232 Port 4 17 Back View Keypad Terminal 9 8 3 RS-232 (DH-485) without additional RS-232 Port 5 2 6 10 1 RS-232 (DH-485) with additional RS-232 Port
Terminal Overview Chapter 1 # Feature Description 1 Power Connection Terminals Connects to external power source. 2 Nameplate Label Provides product information. 3 Reset Button Resets the terminal. 4 Sealing Gasket Seals the front of the terminal to an enclosure or panel. 5 Memory Card Slot Accepts a memory card which stores applications. 6 FAULT Status (Red) Indicator Indicates firmware or hardware faults. 7 COMM Status (Green) Indicator Indicates when communication is occurring.
Chapter 1 Terminal Overview PanelView 1400 Terminal Features This section defines features of the PanelView 1400 terminals. IMPORTANT PanelView 1400 terminals are no longer available. Contact your local sales office or authorized Rockwell Automation Distributor for suitable substitutes.
Terminal Overview Chapter 1 # Feature Description 1 Function Keys (F1…F21) Use the function keys on keypad terminals to initiate functions on the terminal display. These keys may have custom legends. 2 Cursor Keys Use the cursor keys to move the cursor in displayed lists, to select a numeric entry object, or to enter configuration mode. 3 Numeric Entry Keys 0…9 - Enters numeric values. . Enters a decimal point. - Enters a negative value. ← Clears entered digits or cancels the scratchpad.
Chapter 1 Terminal Overview PanelView 1400 Terminal Features (back and sides) Remote I/O, DF1, DH+, DeviceNet, ControlNet, or Ethernet with additional RS-232 Port 19 1 18 17 16 7, 8, 9 10, 11, 12 13, 14, 15, 16 2 10, 11, 12, 13, 14, or 15 DH-485 with additional RS-232 Port 6 5 4 3 Left Side 7 8 16 20 RS-232 (DH-485) with additional RS-232 Port Right Side 9 16 21 46 Publication 2711-UM014G-EN-P - September 2008
Terminal Overview # 1 2 3 4 5 6 7 Feature Brightness Control Contrast Control Nameplate Label FAULT Status (Red) COMM Status (Green) Power Connection Terminals DH-485 Communication Port 8 DH-485 Programming Connector 9 RS-232 (DH-485) Communication Port 10 11 12 13 Remote I/O Port DH+ Communication Port DeviceNet Connector ControlNet Connector 14 15 RS-232 (DF1) Communication Port Ethernet Connector 16 RS-232 Printer/File Transfer Port 17 18 19 20 21 Memory Card Eject Button Memory Card Slot S
Chapter 1 Terminal Overview Applications PanelView terminals operate with custom designed applications. The first time you power on the terminal, (no application file loaded), the terminal displays the Configuration Mode menu. Chapter 3 describes the terminal functions you can configure from this menu. TIP Remote I/O terminals provide an out-of-box application for setting remote I/O communication parameters. If an application is loaded, the terminal displays the application’s start-up screen.
Terminal Overview Chapter 1 Touch Screen Operation Applications for touch screen terminals are controlled by touching screen objects. Keypad Operation Applications for keypad terminals are controlled by pressing function keys that correspond to screen objects. Data is entered manually by using the numeric entry keys. A function key legend kit is available for each terminal (except the PV300 Micro terminal) to create custom labels for the function keys. See the accessories at the end of this chapter.
Chapter 1 Terminal Overview IMPORTANT Configuration Mode Menu The keypad is designed for finger or gloved finger operation. The touch screen may be operated with a finger, gloved finger, or with a touch screen plastic stylus device with a minimum tip radius of 1 mm (0.040 in) to prevent damage to the touch screen. Using any other object or tool may damage the keypad or touch screen. You can configure terminal functions from the Configuration Mode menu.
Terminal Overview Printing Chapter 1 PanelView terminals equipped with an RS-232 printer port can print: • • • • triggered messages in a message display. triggered states of a multistate indicator. alarm messages. alarm lists. Print attributes for objects are defined in the application. Any printer that supports the IBM enhanced character set can be connected to the RS-232 printer port of a PanelView terminal.
Chapter 1 Terminal Overview Accessories This section lists the accessories available for the PanelView terminals. Software Cat. No. 300M 300 550 600 900 1000 1400 Description 2711-ND3 x x x x x x x Windows software required for creating PanelView applications on a personal computer. Function Key Legend Kits Cat. No. 300 2711-NF1 550 600 900 1000 1400 x Description 5 legend inserts with key labels F1…F10 on one side. Use blank side to create custom labels.
Terminal Overview (1) Chapter 1 Contact Rockwell Automation for availability. Antiglare Overlay Self-adhesive filters minimize the reflection of terminal displays. Cat. No.
Chapter 1 Terminal Overview Cat. No. Description 1761-CBL-PM02 2 m (6.5 ft) cable connects an RS-232 terminal to an AIC+ (Port2) through a null modem adapter. 2711-CBL-PM05 5 m programming cable with a D-shell and mini DIN connector. 2711-CBL-PM10 10 m programming cable with a D-shell and mini DIN connector. PanelView File Transfer Utility Cat. No. Description 2711-ND7 Transfers .PVA files between a PanelView terminal and a computer running Windows.
Terminal Overview Chapter 1 RS-232 Cables Cat. No. Description 2711-NC13 5 m (15 ft) connects an RS-232 terminal to the Channel 0 port of an SLC 5/03 controller or the RS-232 port of a computer or printer. 2711-NC14 10 m (32 ft) cable connects an RS-232 terminal to the Channel 0 port of an SLC 5/03 controller or the RS-232 port of a computer or printer. 2711-NC21 5 m (15 ft) connects an RS-232 terminal to a MicroLogix controller (except PV300 Micro).
Chapter 1 Terminal Overview Replacement Parts This section lists the replacement parts available for the PanelView terminals. Backlight Lamps Cat. No. 550 2711-NL1 x 600 900 1000 Description Halogen backlight lamp for all PV550 terminals. Provides backlighting for LCD display. 2711-NL2 x 2711-NL3 Backlight for PV900 color terminal. x Backlight for PV600 color terminal. 2711-NL4 x 2711-NL5 Backlight for PV1000 color terminal.
Terminal Overview Chapter 1 Panel Mount Clips and Studs Cat. No. 600 900 1000 2711-NP1 2711-NP2 x x 1400 Description x 10 panel mount clips for PV1400 terminal. x 6 panel mount clips for PV600, PV900 or PV1000 terminals. 2711-NP3 x Optional panel mount studs (18) for PV1400 terminals. Remote I/O Connector Cat. No. 550 600 900 1000 1400 Description 22112-046-03 x x x x x Terminal block connector plugs into remote I/O port of remote I/O terminals. Power Input Connector Cat. No.
Chapter 1 58 Terminal Overview Publication 2711-UM014G-EN-P - September 2008
Chapter 2 Applying Power and Resetting Terminal Chapter Objectives This chapter provides information on: • • • • Wiring and Safety Guidelines wiring and safety guidelines. connecting AC or DC power. resetting the terminal. power-up sequence. Use publication NFPA 70E, Electrical Safety Requirements for Employee Workplaces when wiring the PanelView terminals. In addition to the NFPA general guidelines: • connect the terminal to its own branch circuit.
Chapter 2 Applying Power and Resetting Terminal Hazardous Location Considerations This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D; Class II, Division 2, Groups F and G; Class III; or non-hazardous locations only. The following WARNING statement applies to use in hazardous locations. WARNING EXPLOSION HAZARD • Substitution of components may impair suitability for Class I, Class II, Class III Division 2.
Applying Power and Resetting Terminal Connect AC Power Chapter 2 Below are AC electrical ratings for the PanelView terminals. The PV550/PV600 touch screen only terminal is available only with DC power, not AC power.
Chapter 2 Applying Power and Resetting Terminal PanelView 550 Terminal 120/240V AC, 3 Wire, 120/240V AC, 3 Wire, European Harmonized Color Code U.S. Color Code L1 L2N GND L1 L2N GND Black (Line) White (Neutral) Blue (Neutral) Green/Yellow (Protective Earth) Brown (Line) Green (Earth Ground) To Power Source To Power Source PanelView 900/1000 Terminal Power Terminal Block (fixed) 120/240V AC, 3 Wire, European Harmonized Color Code L1 L2N GND/PE 120/240V AC, 3 Wire, U.S.
Applying Power and Resetting Terminal Connect DC Power Chapter 2 The L1 versions (Cat. No. 2711-K5 A5 A18...32V1L1, 2711-T9C1L1) of the PV300, PV300 Micro, PV550, PV600, PV900, and PV1000 terminals connect to a 24V DC power source. The table below shows the electrical ratings for the DC versions of the terminals. Electronic circuitry and an internal fuse protect the terminals from reverse polarity and over-voltage conditions.
Chapter 2 Applying Power and Resetting Terminal Connect the power source to the terminal at the 3-screw terminal block (PV300 Micro removable and PV600 Touch only, all others fixed). WARNING Explosion Hazard • Substitution of components may impair suitability for Class I, Class II, Class III, Division 2. • Do not replace components or disconnect equipment unless power has been switched off or the area is known to be non-hazardous.
Applying Power and Resetting Terminal Chapter 2 Follow these steps to connect power to the dc versions of the PanelView. 1. Secure the DC power wires to the terminal block screws. PanelView 300 Terminal PanelView 900/1000 Terminal PanelView 550/600 Terminal Power Terminal Block (fixed) Power Terminal Block (fixed) + - Note: In the PanelView 300, the Earth Ground and DC Negative wires are internally connected.
Chapter 2 Applying Power and Resetting Terminal Reset the Terminal Resetting the terminal re-initializes the PanelView terminal (same as cycling power). Follow these steps to reset the PV300, PV300 Micro, PV550 (keypad, keypad and touch) or the PV600 (keypad, keypad and touch) terminals. • Simultaneously press the Left arrow , Right arrow , and Enter ↵ keys. The terminal performs its powerup sequence.
Applying Power and Resetting Terminal Power-up Sequence Chapter 2 When resetting or applying power to a PanelView terminal, the terminal runs a series of self-tests. The initial display shows copyright information and the status of each self-test number. See Appendix B for a description of the self-test numbers. COPYRIGHT ALLEN-BRADLEY COMPANY 1999, ALL RIGHTS RESERVED VXX.
Chapter 2 Applying Power and Resetting Terminal For Remote I/O Terminals An out-of-box application screen opens allowing you to set remote I/O parameters for the terminal. This screen is only available for initial setup. Once an application is downloaded, the remote I/O setup screen is erased. The table on the next page defines the remote I/O Parameters.
Applying Power and Resetting Terminal Press this function key on 550/600 900/1000/1400 F1 To set this RIO parameter Description Rack # Rack address of terminal on RIO network. 0…76 Chapter 2 Options On PV550/600: Press ↵ to open the scratchpad. Enter the rack address and press ↵ again. On PV900/PV1000/PV1400: Press F1 to set the rack #, then use the up and down arrow keys to select an address.
Chapter 2 70 Applying Power and Resetting Terminal Publication 2711-UM014G-EN-P - September 2008
Chapter 3 Configuring the Terminal Chapter Objectives This chapter shows how to use the Configuration Mode menu to configure terminal settings and perform operations including how to: • • • • • • • • • Application Settings access the Configuration Mode menu. select a language. use a memory card. configure communication (DH485, DH+, remote I/O, ControlNet, DeviceNet, DF1, EtherNet/IP). configure presets. view terminal information. set the time and date. adjust display parameters. set up the printer.
Chapter 3 Configuring the Terminal Access the Configuration Mode Menu The Configuration Mode menu appears on powerup if an application is not loaded or if the menu was last displayed prior to a reset or power down. To access Configuration Mode on keypad terminals if an application is running, simultaneously press the Left and Right arrow keys on the terminal keypad. TIP If the Left or Right arrow keys on the PanelView 300 Micro are assigned as function keys, you must use the GoTo Config. Screen button.
Configuring the Terminal Chapter 3 Run Mode Runs the loaded application. Reset Video Resets the video to default settings. The reset video function is useful if the screen is set to non-viewable settings. Comm and Fault Status Indicators The two status indicators on the Configuration Mode menu indicate the operating state of the terminal. The operating states vary for each communication protocol (and the PV300 Micro terminal). See Chapter 13.
Chapter 3 Configuring the Terminal Language List Select a language using the up or down arrow keys. All configuration screens and terminal messages will be displayed in the selected language. Exit Returns to the Configuration Mode menu. Use a Memory Card Select Memory Card from the Configuration Mode menu to transfer applications between a memory card and the terminal. The PanelView 300 Micro does not support a memory card. Chapter 4 describes the transfer procedure.
Configuring the Terminal Chapter 3 Restore From Card Transfers the application under Applications on Card to the terminal. Any application in the terminal is overwritten. Save to Card Saves the current application in the terminal to the memory card. Erase/Format Card Erases and formats a 2711-NM11, -12, -13, -14, 15 memory card. This function deletes all applications on the card. You can’t delete individual files. Don’t perform this operation on a 2711-NM2xx ATA card or the card will be inoperable.
Chapter 3 Configuring the Terminal DH-485 Max Node: 31 F1 Node: 2 F2 Baud: 19200 F3 Comm LED Fault LED EXIT F16 Max Node Opens the numeric entry scratchpad. Enter the highest node number on the network (up to 31) and press the Enter ↵ key. (On touch screen terminals, press the ↵ key on the scratchpad). A change to the maximum node address takes effect immediately. Node Opens the numeric entry scratchpad. Enter the node address of the terminal (0…31) and press the Enter ↵ key.
Configuring the Terminal Chapter 3 DH+ Communication The DH+ screen lets you display or modify communication settings for the DH+ version of the PanelView terminals. IMPORTANT Settings downloaded with a DH+ application take priority over terminal settings and take effect immediately after the download. DH+ Node: 2 F1 Baud: 57.6 K F2 Comm LED Fault LED EXIT F16 Node Opens the numeric entry scratchpad. Enter the node address (0…77 octal) of the terminal on the DH+ link and press the Enter ↵ key.
Chapter 3 Configuring the Terminal Exit Returns to the Configuration Mode menu. Remote I/O Communication The remote I/O configuration screen lets you display communication settings for a remote I/O terminal. Remote I/O settings are configured with the out-of-box application provided with the terminal or from the PanelBuilder32 software. RIO Configuration Rack Number: Rack Size: Starting Group: Pass-Through Enabled: Last Chassis: 3 Full 0,1 Yes Yes 115.
Configuring the Terminal Chapter 3 Last Chassis (ready only) Indicates whether the terminal occupies the last module group in its assigned rack. Baud Steps through the communication rates with each key press: 57.6K (default), 115.2K, and 230.4K. The selected rate takes effect immediately. The maximum cable length is restricted at higher communication rates. Exit Returns to the Configuration Mode menu.
Chapter 3 Configuring the Terminal New Node Address Opens the numeric entry scratchpad. Enter the node address (01…99 decimal) of the terminal and press the Enter ↵ key. On touch screen terminals, press the ↵ key on the scratchpad. The initial default is 3. The change takes effect after the terminal is reset. If you enter a value greater than the UMAX node address, the terminal will not go online with the network. Active Node Address (read only) Displays the current address of the PanelView terminal.
Configuring the Terminal Chapter 3 Displayed Value Status AB Displayed Value Status AB Displayed Value Status AB Displayed Value Status AB 115 3 7 83 3 5 51 3 3 19 3 1 114 2 7 82 2 5 50 2 3 18 2 1 113 1 7 81 1 5 49 1 3 17 1 1 112 0 7 80 0 5 48 0 3 16 0 1 103 7 6 71 7 4 39 7 2 7 7 0 102 6 6 70 6 4 38 6 2 6 6 0 101 5 6 69 5 4 37 5 2 5 5 0 100 4 6 68 4 4 36 4 2 4 4 0 99 3 6 67 3 4 35 3 2 3 3 0 98 2 6 66 2 4 34 2 2 2 2 0
Chapter 3 Configuring the Terminal DeviceNet Communication The DeviceNet screen lets you display or modify communication settings for a DeviceNet terminal. IMPORTANT Settings downloaded with a DeviceNet application take priority over terminal settings and take effect immediately after the download.
Configuring the Terminal Chapter 3 New Baud Step through the communication rates with each key press: 125K (default), 250K, 500K, AutoBaud, PGM. If you select AutoBaud, the terminal determines the communication rate on startup (provided there is sufficient network traffic). If you select PGM, the terminal uses the most recent communication rate stored on the communication card. The selected communication rate takes effect on reset. The maximum cable length is restricted at higher communication rates.
Chapter 3 Configuring the Terminal Input Size Displays the number of words (0…64) sent by the PanelView in an I/O message. The default value is 0, which indicates that no input data is exchanged with the scanner. This value is set by the downloaded application. Output Size Displays the number of words (0…64) received by the PanelView in an I/O message. The default value is 0, which indicates no output data is exchanged with the scanner. This value is set by the downloaded application.
Configuring the Terminal Chapter 3 Communication Parameters Sets the communication parameters for the DF1 port on the PanelView terminal. The settings must match the target device. Each key press toggles through the available combinations for: • Parity = None (default), Even or Odd • Data Bits = 8 • Stop Bits = 1 (default) or 2 The DF1 port on the PLC-5 controllers allows a parity of Even or None parity with 8 Data Bits. For the SLC controllers, the parity is fixed at None and uses CRC error detection.
Chapter 3 Configuring the Terminal Comm Status Indicator • solid fill - normal operating state • blinking - no communication established with logic controller • no fill - hardware failure Fault Status Indicator • no fill - normal operating state • blinking - hardware is functioning but an application is not loaded or the current application is corrupted. Exit Returns to the Configuration Mode menu.
Configuring the Terminal Chapter 3 DHCP/BootP Enable DHCP/BootP Enable (Dynamic Host Configuration Protocol) automatically allocates network devices and configurations to newly attached devices on a TCP/IP network. When DHCP/BootP Enable is enabled, the PanelView terminal is automatically assigned an IP Address and Subnet Mask. These fields will be read only. Select disable to manually enter an IP Address or Subnet Mask for the PanelView terminal.
Chapter 3 Configuring the Terminal Restart Terminal Resets the terminal. Exit Returns to the Configuration Mode menu. Configure Presets Select Preset Operations from the Configuration Mode menu to set the values of control objects after a reset or power cycle. You can set presets to: • values provided by the PanelView application. • last values entered from terminal prior to a reset or power down.
Configuring the Terminal Chapter 3 Key Repeat Rate Specifies the number of repeats that occur per second when a key is pressed and held. Steps through key repeat rates: 0 (disabled), 200 ms (5 times/s), 250 ms (4 times/s), 330 ms (3 times/sec), 500 ms (2 times/s), 1000 ms (1 time/s). Key Repeat Delay Specifies how long a key must be pressed before it is repeated. Steps through delay rates: 200 ms, 400 ms, 600 ms, 800 ms, 1000 ms, 1500 ms, 2000 ms, 2500 ms. Exit Returns to the Configuration Mode menu.
Chapter 3 Configuring the Terminal Communication Port (P#.xxx, for example, P0.485 or P1.232) Screen Size (SS5.5, SS6.0, SS9.0, SS10.0, SS14.0) Filename Displays the name of the active application file. If the application file exists but is invalid, the file name appears as ********. • Bytes Used displays the number of bytes used by the loaded application. • Bytes Free displays the number of bytes available. Font File Displays the name of the external font file used by the application.
Configuring the Terminal Chapter 3 Contrast Increases or decreases the display contrast. The contrast settings range from 0…10. Video Mode Toggles between normal video (dark text/graphics on a light background) and reverse video (light text/graphics on a dark background). Changes take effect immediately. Screen Saver Mode Mode - Select Timed or Off screen saver.
Chapter 3 Configuring the Terminal Contrast Increases or decreases the display contrast. The contrast settings range from 0…10. Video Mode Toggles between normal video (dark text/graphics on a light background) and reverse video (light text/graphics on a dark background). Changes take effect immediately. Reset Video Resets the display to normal (default settings). The [F3] key is also active on the Configuration Mode menu.
Configuring the Terminal Chapter 3 PanelView 550 Terminal Screen Setup SCREEN SETUP Backlight Off F2 F7 Contrast 10 F3 Backlight Timeout 10 min. IMPORTANT F9 Reset Video F4 Video Mode Reverse EXIT F10 Certain settings may make viewing the screen difficult. Do not exit this screen until viewing adjustments are acceptable. Backlight Turns the backlight On, Off or to Timed mode. When set to Timed, the Backlight Timeout value determines when the backlight is turned off.
Chapter 3 Configuring the Terminal Exit Returns to the Configuration Mode menu. PanelView 600/900/1000 Color Terminal Screen Setup SCREEN SETUP Screen Saver Off F1 Normal Intensity 100 F2 SCREEN SAVER Timeout Intensity 10 min. 0 F10 F9 SCREEN SETUP SCREEN SAVER Timed Reset Video F15 F1 Timeout 10 min.
Configuring the Terminal Chapter 3 Screen Saver Intensity Adjusts the intensity of the display during screen saver mode. PV600/1000 settings are 0…100, in 10 step increments. PV600 touch-screen only settings are 0 or 100. PV900 settings are 0, and 50…100, in 10 step increments. It is recommended that you set the intensity to a value less than 100 to prolong the life of the backlight. Reset Video Resets the display to normal video (default settings).
Chapter 3 Configuring the Terminal Screen Saver Mode Sets the screen saver to Timed or Off. When Timed, the screen intensity is reduced if user input or a controller screen change is not received within the time specified in the Screen Saver Timeout box. Screen Saver Timeout Specifies when an inactive screen enters screen saver mode. The timeout is adjusted in steps with each key press: 5, 10, 15, 20, 25, or 30 minutes.
Configuring the Terminal Chapter 3 Reset Video Resets the display to normal video (default settings). On keypad terminals, the reset video [F15] key is also active on the Configuration Mode menu. If the screen is non-viewable, press the Left and Right arrow keys simultaneously. Then press [F15] to reset the screen. Exit Returns to the Configuration Mode menu. PanelView 1000 Grayscale Terminal Screen Setup SCREEN SETUP Screen Saver Video Mode Normal Off F2 F1 SCREEN SAVER Timeout Intensity 10 min.
Chapter 3 Configuring the Terminal Screen Saver Intensity Adjusts the intensity of the display during screen saver mode. Settings are 0 (lowest intensity) or 100 (highest intensity). 0 is recommended to prolong the display life. Reset Video Resets the display to normal video (default settings). On keypad terminals, the reset video [F15] key is also active on the Configuration Mode menu. If the screen is non-viewable, press the Left and Right arrow keys simultaneously.
Configuring the Terminal Chapter 3 Screen Saver Intensity Adjusts the intensity of the display during screen saver mode. The intensity is adjusted with each key press: 0, 25, 50, 75, or 100. Degauss Auto Enables or disables automatic degaussing. The degauss process takes a few seconds and will not start until the terminal is inactive. Automatic degaussing occurs at midnight unless you adjust the hour and time parameters. Degauss Hour Specifies the hour to start automatic degaussing.
Chapter 3 Configuring the Terminal Align Touch Grid - PV1400 Touch Screen Terminal only Opens the touch alignment screen, which lets you realign the screen with the touch grid. This function is useful when the terminal is positioned at an angle and viewing the screen is difficult unless you realign the screen. EXIT F16 Move the screen until it aligns with the touch cells. Alignment changes are permanent. Press To Move the screen up one pixel. Move the screen down one pixel.
Configuring the Terminal Chapter 3 Set the Time Use screen buttons (touch screens) or function keys to set the time. On PV300, PV300 Micro Terminals On PV550/PV600 Terminals Press On PV900/1000/1400 Terminals Press To Set Use the left and right cursor keys to select the time or date item you want to change. Use the up and down cursor keys to adjust the selected date or time variable.
Chapter 3 Configuring the Terminal Set Up the Printer Select Printer Setup from the Configuration Mode menu to set parameters for those terminals equipped with an RS-232 printer port. Any printer that supports the IBM enhanced character set can be connected to the RS-232 printer port.
Configuring the Terminal Chapter 3 Baud Rate Sets the communication rate of the printer port. The communication rate must match the communication rate of the printer. The communication rate is adjusted with each key press: 1200, 2400, 4800, 9600, and 19200. The initial default is 9600. Top of Form Notifies the PanelView terminal the printer is at the top of a page. Manually adjust the printer to the top of the page before pressing the Top of Form button.
Chapter 3 104 Configuring the Terminal Publication 2711-UM014G-EN-P - September 2008
Chapter 4 Using a Memory Card Chapter Objectives This chapter describes: • supported memory cards. • using the memory card retainer. • loading application from a memory card. • loading application on a memory card. • storing font files on a memory card. • removing a memory card. Supported Memory Cards Memory cards are available to transfer application files to/from a PanelView terminal with a memory card slot. The PanelView 300 Micro terminal does not support a memory card.
Chapter 4 Using a Memory Card Use the Memory Card Retainer A memory card retainer (catalog no. 2711-NMCC, -NMCD, -NMCE) is shipped with all PanelView terminals, except the PV300 Micro terminal and the PV1400 terminal. It is required for: • UL508 installations. • vibration/mechanical shock environments. • CE certified installations. • installations where the application uses a font file on a memory card, and the card must remain in the terminal during operation.
Using a Memory Card Chapter 4 The memory card retainer protects against: • electrical shock from loose high voltage wires in an electrical enclosure per UL508. ATTENTION When permanently installing a memory card in an electrical enclosure, the memory card retainer must be used to avoid accidental contact of high voltage leads to metal surfaces on the card. Failure to use the retainer could result in physical injury or damage to the terminal. • electrostatic discharge (ESD) up to 15KV.
Chapter 4 Using a Memory Card Load Application from a Memory Card The procedure below shows how to load an application on a memory card into the PanelView terminal. WARNING Explosion Hazard - Do not install or remove memory card unless power has been switched off or the area is known to be non-hazardous. Follow these steps to load an application from a memory card. 1. Insert the memory card in the card slot of the terminal.
Using a Memory Card Chapter 4 4. Press Memory Card Listing, [F1] on keypad terminals, until the application file you want to load is displayed. 5. Press Restore From Card, [F2] on keypad terminals, to begin the transfer. Because this operation overwrites the current application in the terminal, you are prompted to abort or continue. Proceed with download? F1 - Abort| F2 - Continue The terminal displays the status of the transfer. In progress ... 6.
Chapter 4 Using a Memory Card Load Application on a Memory Card The steps below show how to load an application in the terminal onto a memory card. WARNING Explosion Hazard - Do not install or remove memory card unless power has been switched off or the area is known to be non-hazardous. Follow these steps to transfer an application to a memory card. 1. Insert the memory card into the card slot of the terminal. 2.
Using a Memory Card Chapter 4 Because this operation erases all data on the memory card, you are prompted to abort or continue. Format erases entire card? F1 - Abort F2 - Continue 5. Press Save to Card, [F3] on keypad terminals, to transfer the application in the terminal to the card. If the application already exists on the memory card, you are prompted to abort or continue. The .PVA file exits: F1 - Abort F2 - Upload with new PVA file The terminal displays the status of the transfer. In progress...
Chapter 4 Using a Memory Card To view the name of the font file used by an application, select Terminal Info from the Configuration Mode menu. Because the memory card must remain in the terminal while the application is running, we recommend that you use the memory card retainer (Cat. No. 2711-NMCC, 2711-NMCD, 2711-NMCE) to secure the card in the card slot. The retainer ensures the card is not accidentally removed or dislodged during terminal operation.
Chapter 5 Running Applications Chapter Objectives This chapter describes operating procedures common to most applications.
Chapter 5 Running Applications • Simultaneous pressing of Left and Right cursor keys does not cause the terminal to enter Configuration Mode if the Left and Right cursor keys are assigned as function keys anywhere in the application. • If both the Left/Right cursor keys are used on a screen and more than one cursor operated object is present on the screen, all of the cursor operated objects must be assigned to a function key.
Running Applications Chapter 5 • All push buttons are momentarily disabled (0.5 second) after a screen change. This prevents multiple buttons, in the same location on different screens, from being pressed inadvertently. • All push buttons must be released on the previous screen before buttons can be pressed on the new screen. • Momentary push buttons are assigned a hold time. The hold time maintains the pressed state so that each change of state can be read by the controller at least once.
Chapter 5 Running Applications Active Control List Has a vertical indicator bar on the left side of the list. Only one control list or numeric entry cursor point can be active on a screen. To activate a control list: • touch the object (touch screen terminals only) • or press the assigned function key • or on a screen with multiple control lists or numeric entry cursor points, press the Left or Right arrows to move the indicator bar between the objects.
Running Applications Chapter 5 List Keys Touch screen terminals require list keys on the screen to move the cursor in a control list and select entries. The following table shows the list keys. List Key Type Description Move Up Moves the cursor to the previous item in the list. Move Down Moves the cursor to the next item in the list. Home Moves the cursor to the first item in the list. End Moves the cursor to the last item in the list. Page Up Moves the cursor up one page in a scrolling list.
Chapter 5 Running Applications Follow these steps to select an item on a control list. 1. Select the control list by: • touching the screen object (touch screen terminals only). • pressing its function key. • pressing the Left or Right arrow keys until the control list has a vertical bar indicating it is active. 2. Move the cursor up or down the list using the Up or Down arrows. If the cursor is hollow, the item cannot be selected. 3.
Running Applications Chapter 5 Scratchpad Both controls display a numeric entry scratchpad in the center of the screen. The scratchpad shows the current value entered and the range of possible values you can enter. Current value entered in scratchpad 550/600 Touch Screen only Terminal Scratchpad Keypad and Keypad/Touch Screen Terminal Scratchpad 900/1000/1400 Touch Screen Terminal Scratchpad During data entry, wait until the number you enter appears in the scratchpad before entering the next number.
Chapter 5 Running Applications Follow these steps to enter a value by using the keypad enable button. 1. Press the keypad enable button. The scratchpad opens. 2. Enter the value by using the terminal keypad and press Enter ↵ . Follow these steps to change an entry on a scratchpad. 1. Press the backspace ←key to delete one character at a time. 2. Enter a new value and press Enter ↵ . Follow these steps to cancel a scratchpad. 1. Press the Backspace ←key to delete one character at a time.
Running Applications ASCII Entry Controls Chapter 5 ASCII entry controls let you send an alphanumeric string (up to 128 characters) to a controller. Like numeric entry controls, the ASCII entry control can appear on a screen as a keypad enable button or a cursor point. When either object is activated, the ASCII scratchpad opens. The look of the scratchpad depends on the terminal.
Chapter 5 Running Applications Controls Location Function >> F4 Function Keys Moves the cursor one character to the right in the Display Area. ESC 5 Function Keys Closes the scratchpad without making any changes. CTRL F6 Function Keys Clears the string in the Display Area. ASCII Scratchpad - PV300 Micro/300 Terminals The thumbwheel scratch pad lets you enter values on terminals without a numeric keypad or touch screen by cycling through the available characters one position at a time.
Running Applications Chapter 5 ASCII Scratchpad - PV550/600 Touch Screen Terminals Character Keyboard Cursor Display Area Cursor Control Keys Controls To select characters from the Character Keyboard, press the cursor control keys to move the cursor over a character and then press the SEL key. The character is entered in the Display Area. This area scrolls so you can enter a string that is longer than the Display Area. All characters are sent to the controller even if not visible.
Chapter 5 Running Applications ASCII Scratchpad - PV900/1000/1400 Touch Screen Terminals Display Area Character Keyboard Controls Select characters by touching the Character Keyboard on the screen. The character is entered in the Display Area. This area scrolls so you can enter a string that is longer than the Display Area. All characters are sent to the controller even if not visible. After entering the characters, press ↵ on the scratchpad to send the characters to the controller.
Running Applications Controls Function CLR Clears the string in the Display Area. ¨ Deletes the character to the left of the cursor in the Display Area. ↵ Chapter 5 Sends the character string to the assigned write tag address in the controller. After pressing ↵ to open the ASCII scratchpad, the string is highlighted. If you select a character immediately, the terminal clears the Display Area and displays the selected character.
Chapter 5 Running Applications Screen Selectors The 2 types of screen selector controls are Screen List Selectors and Screen buttons. Screen List Selector Screen Controls Monitor Pump Status Vertical Bar indicates active list Valve Status Tank Control Tank Screen Goto Screen Button Previous Screen Return Screen Button Goto and Return screen buttons can have a variety of appearances such as unique inner text, fill pattern, border or shape. Return screen buttons display the previous screen.
Running Applications Chapter 5 Cursor Operation Cursor operation is configured by the application designer.
Chapter 5 Running Applications List Indicators List indicators highlight an item from a list depending upon the status of either a bit or value at a controller address. List Indicator Mixer Speed Off Low Medium High Current status is highlighted Mixer On Mixer Off An indicator list may have a maximum of 255 entries. The list automatically scrolls to display the status of an item. List indicators do not have a cursor selector lists.
Running Applications Analog Gauges The analog gauge uses a rotating needle to display a process variable such as speed, temperature or pressure. The gauge consists of a circular scale with tick-marks, 1… 4 needles, and a label with text or variable data. The circular scale is an integral part of the gauge but can be created separately. 80 100 120 140 60 Pressure 40 160 180 20 0 Numeric Data Displays Chapter 5 200 Numeric Data Displays may appear with or without supporting text.
Chapter 5 Running Applications Time or Date Time and date information can appear as a separate item or in some control/display objects (push buttons, multistate indicators, message displays or data displays). A time and date can appear with or without supporting text. The date can have a variety of formats.
Running Applications Alarms Chapter 5 Applications that support alarms may contain: • Alarm Banner display that pops up when an alarm is triggered • Alarm buttons that enable the operator to act on an alarm (Print Alarm, Acknowledge Alarm, Clear Alarm, Acknowledge All) • Alarm List which stores information on triggered alarms (Print Alarm List or Clear Alarm List button) Alarm configurations are application dependent.
Chapter 5 132 Running Applications Publication 2711-UM014G-EN-P - September 2008
Chapter 6 Installing the PV300 Micro Terminal Chapter Objectives This chapter shows how to install the PanelView 300 Micro terminal and covers: • hazardous locations • enclosures • required tools • mounting dimensions • clearances • cutout dimensions • installing the PV300 micro terminal in a panel Hazardous Location Considerations This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D; Class II, Division 2, Groups F, G; Class III; or non-hazardous locations only.
Chapter 6 Installing the PV300 Micro Terminal Use only the following communication cables in Class 1, Division 2, Hazardous Locations.
Installing the PV300 Micro Terminal Cutout Dimensions Chapter 6 Use the full size template shipped with the PV300 Micro terminal to mark the cutout dimensions. The figure below shows a reduced scale cutout. A full scale template is also available inside the back cover of this document. 112 mm (4.42 in.) 4.5 mm (0.178 in.) diameter 102 mm (4.0 in.) 92 mm (3.62 in.) 54 mm (2.12 in.) Clearances Allow 51 mm (2.0 in.) of space on all sides of the terminal for adequate ventilation and maintenance.
Chapter 6 Installing the PV300 Micro Terminal Install Terminal in Panel Follow these steps to install the PV300 Micro in a panel. ATTENTION • Disconnect all electrical power from the panel before making cutout. • Make sure area around the panel cutout is clear. • Take precautions so that metal cuttings do not enter any components already installed in panel. • Failure to follow this warning may result in personal injury or damage to the panel components. 1.
Installing the PV300 Micro Terminal Chapter 6 6. Tighten the nuts to a torque of 1.13 Nm (10 lb-in). Do not overtighten. ATTENTION Publication 2711-UM014G-EN-P - September 2008 Mounting nuts must be tightened to a torque of 1.13 Nm (10 lb-in) to provide a proper seal and to prevent potential damage to the terminal. Allen-Bradley assumes no responsibility for water or chemical damage to the terminal or other equipment within the enclosure because of improper installation.
Chapter 6 138 Installing the PV300 Micro Terminal Publication 2711-UM014G-EN-P - September 2008
Chapter 7 Installing the PV300 Terminal Chapter Objectives This chapter shows how to install the PanelView 300 terminal and covers: • hazardous locations. • enclosures. • required tools. • mounting dimensions. • clearances. • cutout dimensions. • installing the PV300 terminal in a panel. Hazardous Location Considerations This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D; Class II, Division 2, Groups F and G; Class III; or non-hazardous locations only.
Chapter 7 Installing the PV300 Terminal The PV300 terminals have an operating temperature code of T4 (maximum operating temperature of 135 ° C or 275 °F). Do not install these terminals in environments where atmospheric gases have ignition temperatures less than 135 °C (275 °F). Enclosures Mount the PV300 terminal in a panel or enclosure to protect the internal circuitry. The terminal meets NEMA Type 12/13 and 4X (indoor use) ratings only when mounted in a panel or enclosure with the equivalent rating.
Installing the PV300 Terminal Mounting Dimensions Chapter 7 The illustration below shows mounting dimensions for the PV300 keypad terminals. Top View 197 mm (7.76 in) 69 mm (2.73 in) 82 mm (3.21 in) 140 mm (5.53 in) Cutout Dimensions Use the full size template shipped with the PV300 terminal to mark the cutout dimensions. Below is a reduce size cutout. 120 mm 4.71 in.) 109 mm 4.29 in.) Recommended Panel Publication 2711-UM014G-EN-P - September 2008 R 4.5 mm via (0.178 in.) 140 mm 5.53 in.
Chapter 7 Installing the PV300 Terminal Clearances When installing the PV300 terminal, allow space for mounting, air flow, maintenance, memory card and legend strip installation. Side, Top and Bottom Clearances Leave 64 mm (2.5 in.) for Mounting and Air Flow Terminal Cutout Recommended Panel Use full size template shipped with terminal Leave 64 mm (2.5 in.) for Mounting and Air Flow Back Clearance 69 mm (2.73 in.) 134.6 mm (5.3 in.) Memory Card Retainer 215.9 mm (8.5 in.
Installing the PV300 Terminal Install the PV300 Terminal in a Panel Chapter 7 Follow these steps to install the PV300 terminal in a panel. ATTENTION • Disconnect all electrical power from the panel before making the cutout. • Make sure the area around the panel cutout is clear. • Do not allow metal cuttings to enter any components that may already be installed in the panel. • Failure to follow this warning may result in personal injury or damage to the panel components. 1.
Chapter 7 Installing the PV300 Terminal 6. Install the self-locking nuts hand tight. Protective installation label Self-locking nuts (4 used, 6 provided) Mounting Studs (2 left, 2 right) 7. Alternately tighten the self-locking nuts until the terminal is held firmly against the panel 8. Tighten the nuts to a torque of 1.13 Nm (10 lb-in). Do not over-tighten. ATTENTION Mounting nuts must be tightened to a torque of 1.
Chapter 8 Installing the PV550 Terminal Chapter Objectives This chapter describes how to mount the PV550 terminal in a panel or enclosure including: • • • • • • • Hazardous Location Considerations hazardous locations enclosures required tools mounting dimensions clearances cutout dimensions installing the PV550 terminal in a panel This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D or non-hazardous locations only.
Chapter 8 Installing the PV550 Terminal The following PV550 terminals have an operating temperature code of T2 (maximum operating temperature of 300 ° C or 572 °F). • keypad terminals (series G or earlier) • keypad and touch screen terminals (series G or earlier) • touch screen only terminals (series A) Do not install these terminals in environments where atmospheric gases have ignition temperatures less than 300 °C (572 °F).
Installing the PV550 Terminal Required Tools Chapter 8 Other than the tools required to make the PV550 panel cutout, the tools required for installation are: • 7 mm (M4) deep well socket wrench or nut driver • small slotted screwdriver • torque wrench (lb-in) Mounting Dimensions The illustration below shows mounting dimensions for the PV550 terminals. PV550 Keypad, Keypad & Touch Screen Terminals Top View 167 mm (6.57 in.) 106 mm (4.17 in.) 86 mm (3.39 in.) 266 mm (10.47 in.
Chapter 8 Installing the PV550 Terminal Clearances When installing the PV550 terminal, allow space for mounting, air flow, maintenance, memory card and legend strip installation. PV550 Keypad, Keypad & Touch Screen Terminals PV550 Touch Screen Terminals Leave 25 mm (1.0 in.) for Mounting and Air Flow Terminal Cutout Use full size template shipped with terminal Leave 25 mm (1.0 in.) for Mounting and Air Flow Leave 38 mm (1.5 in.) for Mounting, Air Flow and Wiring Connections Back Clearance 64 mm (2.
Installing the PV550 Terminal Cutout Dimensions Chapter 8 Use the full size template shipped with the PV550 terminal to mark the cutout dimensions. Below is a reduce size cutout. PV550 Keypad, Keypad and Touch Screen Terminals 25.9 mm (1.02 in.) 3.3 mm (0.13 in.) 150 mm (5.91 in.) 106 mm (4.19 in.) 191 mm (7.51 in.) 85 mm (3.33 in.) 243 mm (9.55 in.) 4.8 mm dia (0.188 in.) Front Recommended Panel Cutout Dimensions 3.3 mm (0.13 in.) 144 mm (5.66 in.) PV550 Touch Screen Terminals 4.8 mm dia.
Chapter 8 Installing the PV550 Terminal Install the PV550 Terminal in a Panel Follow these step to install the PV550 terminal in a panel. ATTENTION • Disconnect all electrical power from the panel before making the cutout. • Make sure the area around the panel cutout is clear. • Do not allow metal cuttings to enter any components that may already be installed in the panel. • Failure to follow this warning may result in personal injury or damage to the panel components. 1.
Installing the PV550 Terminal Chapter 8 PV550 Keypad, Keypad & Touch Screen Terminals Mounting Studs (3 top, 3 bottom) Protective installation label Self-locking nuts (6 used, 8 provided) PV550 Touch Screen Terminal Protective installation label Mounting Studs (2 left, 3 right) Self-locking nuts (4 used, 8 provided) 8. Alternately tighten the self-locking nuts until the terminal is held firmly against the panel. 9. Tighten nuts to a torque of 1.13 Nm (10 lb-in). Do not over-tighten.
Chapter 8 Installing the PV550 Terminal 10. Remove protective installation label from top vents of terminal. ATTENTION 152 Failure to remove the protective installation label covering the top vents could result in overheating and damage to the terminal.
Chapter 9 Installing the PV600 Terminal Chapter Objectives This chapter describes how to mount the PV600 terminal in a panel or enclosure including: • • • • • • • Hazardous Location Considerations hazardous locations enclosures required tools mounting dimensions cutout dimensions clearances installing the PV600 terminal in a panel This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D; Class II, Division 2, Groups F, G; Class III; or non-hazardous locations only.
Chapter 9 Installing the PV600 Terminal Enclosures Mount the PV600 terminal in a panel or enclosure to protect the internal circuitry. The terminal meets NEMA Type 12/13 and 4X (indoor use) ratings only when mounted in a panel or enclosure with the equivalent rating. Allow enough space within the enclosure for adequate ventilation. Consider heat produced by other devices in the enclosure.
Installing the PV600 Terminal Mounting Dimensions Chapter 9 The illustration below shows mounting dimensions for the PV600 terminals. PV600 Keypad, Keypad and Touch Screen Terminals 6.9 mm (0.27 in.) 192 mm (7.55 in.) Top View 116 mm (4.57 in.) 91 mm (3.60 in.) 290 mm (11.40 in.) PV600 Touch Screen Terminals Top View 152 mm (6.00 in.) 79 mm (3.12 in.) 96 mm (3.80 in.) 185 mm (7.28 in.
Chapter 9 Installing the PV600 Terminal Cutout Dimensions Use the full size template shipped with the PV600 terminal to mark the cutout dimensions. Below is a reduce size cutout. PV600 Keypad, Keypad and Touch Screen Terminals 167 mm (6.57 in.) Recommended Panel Cut-out Dimensions 264 mm (10.39 in.) PV600 Touch Screen Terminals 4.8 mm dia. (0.188 in.) 98 mm (3.86 in.) 156 165 mm (6.49 in.) 158 mm (6.20 in.) Recommended Panel Cut-out Dimensions R 1.8 mm (0.07 in.) 125 mm (4.91 in.
Installing the PV600 Terminal Clearances Chapter 9 When installing the PV600 terminal, allow adequate space for mounting, air flow, maintenance, memory card and legend strip installation. PV600 Keypad and Keypad and Touch Screen Terminals Side, Top and Bottom Clearances 51 mm (2.0 in.) for Mounting and Air Flow 25 mm (1.0 in.) for Mounting and Air Flow 6.9 mm (0.27 in.) Terminal Cutout - Front View Use full size template shipped with terminal Back Clearance 91 mm (3.60 in.
Chapter 9 Installing the PV600 Terminal Install the PV600 in a Panel To install the PV600 terminal in a panel: ATTENTION • Disconnect all electrical power from the panel before making the cutout. • Make sure the area around the panel cutout is clear. • Do not allow metal cuttings to enter any components that may already be installed in the panel. • Failure to follow this warning may result in personal injury or damage to the panel components. 1.
Installing the PV600 Terminal Chapter 9 4. Install the 4 mounting clips (2 on top, 2 on bottom). The ends of the clips slide into the slots on the terminal. 5. Tighten the clip mounting screws by hand until the gasket seal contacts the mounting surface uniformly.
Chapter 9 160 Installing the PV600 Terminal Publication 2711-UM014G-EN-P - September 2008
Chapter 10 Installing the PV900/1000 Terminals Chapter Objectives This chapter describes how to mount the PV900 and PV1000 terminals in a panel or enclosure including: • • • • • • Hazardous Location Considerations hazardous locations and enclosures required tools mounting dimensions clearances cutout dimensions installing the PV900/PV1000 terminal in a panel This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D; or non-hazardous locations only.
Chapter 10 Installing the PV900/1000 Terminals The PV900/PV1000 terminals have an operating temperature code of T4 (maximum operating temperature of 135 ° C or 275 °F). Do not install the terminals in environments where atmospheric gases have ignition temperatures less than 135 °C (275 °F). Enclosures The PV900/PV1000 terminal must be mounted in an environment that provides IEC-1131-2 Pollution degree 2 protection. Mount the terminal in a panel or enclosure to protect the internal circuitry.
Installing the PV900/1000 Terminals PV900 Terminals Mounting Dimensions IMPORTANT Chapter 10 PanelView 900 terminals are no longer available. Contact your local sales office or authorized Rockwell Distributor for suitable substitutes. The illustrations below show mounting dimensions for the PV900 monochrome and color terminals. PV900 Touch Terminal Mounting Dimensions 6.9 mm (0.27 in.) 249 mm (9.80 in.) Top View 112 mm (4.40 in.) 90 mm (3.54 in.) 336 mm (13.24 in.
Chapter 10 Installing the PV900/1000 Terminals PV1000 Terminals Mounting Dimensions The illustrations below show the mounting dimensions for the PV1000 grayscale and color terminals. PV1000 Touch Terminal Mounting Dimensions 6.9 mm (0.27 in.) 282 mm (11.11 in.) Top View 112 mm (4.40 in.) 90 mm (3.54 in.) 370 mm (14.58 in.) PV1000 Keypad Terminal Mounting Dimensions 6.9 mm (0.27 in.) 282 mm (11.11 in.) 90 mm (3.54 in.) Top View 112 mm (4.40 in.) 423 mm (16.64 in.
Installing the PV900/1000 Terminals Clearances Chapter 10 Allow adequate space for mounting, air flow, maintenance, memory card and legend strip installation. IMPORTANT If using a memory card and/or memory card retainer, allow a back clearance to load the card. Side, Top and Bottom Clearances Leave 51 mm (2.0 in.) for Mounting and Air Flow Leave 51 mm (2.0 in.) for Mounting and Air Flow Terminal Cutout - Front View Use full size template shipped with terminal Leave 51 mm (2.0 in.
Chapter 10 Installing the PV900/1000 Terminals Cutout Dimensions Use the full size template shipped with the PV900 and PV1000 terminals to mark the cutout dimensions. The following illustrations show reduced cutouts for these terminals with dimensions. PV900 Panel Cutout Dimensions PV900 Touch Screen Terminals PV900 Keypad Terminals 224 mm (8.8 in.) Recommended Panel Cut-out Dimensions 224 mm Recommended Panel Cut-out Dimensions (8.8 in.) 305 mm (12.00 in.) 375 mm (14.75 in.
Installing the PV900/1000 Terminals Install the PV900/PV1000 Terminals in a Panel Chapter 10 Follow these steps to install the PV900/PV1000 terminal in a panel. ATTENTION • Disconnect all electrical power from the panel before making the cutout. • Make sure the area around the panel cutout is clear. • Do not allow metal cuttings to enter any components that may already be installed in the panel. • Failure to follow this warning may result in personal injury or damage to the panel components. 1.
Chapter 10 Installing the PV900/1000 Terminals 4. Install the 6 mounting clips (2 on top, 2 on bottom, 1 on each side). The ends of the clips slide into the slots on the terminal. 5. Tighten the clip mounting screws by hand until the gasket seal contacts the mounting surface uniformly. Protective installation labels Install six mounting clips: Top - left and right slots Bottom - left and right slots Sides - left and right 6. Alternately tighten the mounting clip screws to a torque of 1.13 Nm (10 lb-in).
Chapter 11 Installing the PV1400 Terminal Chapter Objectives IMPORTANT PanelView 1400 terminals are no longer available. Contact your local sales office or authorized Rockwell Distributor for suitable substitutes.
Chapter 11 Installing the PV1400 Terminal For stud mounting: • 7/32 and 3/8 in. socket • 406 mm (16 in.) extension rod (minimum) • socket driver (lb-in torque wrench recommended) Mounting Dimensions The illustrations below show mounting dimensions for the PV1400 terminals. PV1400 Touch Terminal Mounting Dimensions 3.3 mm (0.13 in.) 355 mm (13.97 in.) Top View 394 mm (15.53 in.) 370 mm (14.58 in.) 441 mm (17.37 in.) PV1400 Keypad Terminal Mounting Dimensions 3.3 mm (0.13 in.) 3 mm (13.97 in.
Installing the PV1400 Terminal Clearances Chapter 11 Allow adequate space for mounting, air flow, maintenance, adjusting brightness/contrast, memory card and legend strip installation. IMPORTANT If using a memory card, allow a back clearance to load the card. Side, Top and Bottom Clearances Leave 51 mm (2.0 in.) for Mounting and Air Flow Terminal Cutout - Front View Use full size template shipped with terminal Leave 51 mm (2.0 in.) for Mounting Leave 51 mm (2.0 in.) for Mounting and Air Flow 3.
Chapter 11 Installing the PV1400 Terminal Cutout Dimensions Use the full size template provided with the terminal to mark cutout dimensions. The illustration below shows reduced size cutouts with dimensions. PV1400 Keypad Terminals 419 mm (16.50 in.) 110 mm (4.35 in.) 221 mm (8.70 in.) 170 mm (6.70 in.) 5.56 mm (7/32 in.) 18 holes 140 mm (5.50 in.) 38 mm (1.50 in.) Ignore stud holes if mounting terminal using panel clips. 305 mm (12.0 in.) 233 mm (9.16 in.
Installing the PV1400 Terminal Install the PV1400 Terminal in a Panel Chapter 11 This section gives procedures for mounting a PV1400 terminal by using: • mounting clips (10 shipped with terminal, 10 required) • mounting studs (ordered separately, Catalog No. 2711-NP3) ATTENTION • Disconnect all electrical power from the panel before making the cutout. • Make sure the area around the panel cutout is clear. • Do not allow metal cuttings to enter any components that may already be installed in the panel.
Chapter 11 Installing the PV1400 Terminal TIP The PV1400 terminal has two metal tabs (on bottom edge) that temporarily lock the terminal against the panel. These tabs only facilitate installation of the mounting hardware. The tabs are not designed to provide permanent mounting. 4. Install the 10 mounting clips (three on top, three on bottom, two on each side). The ends of the clips slide into slots on the terminal. 5. Tighten the clip mounting screws hand tight.
Installing the PV1400 Terminal Chapter 11 Mount Terminal with Mounting Studs Follow these steps to install the PV1400 terminal in a panel by using mounting studs. 1. Cut an opening in the panel by using the panel cutout template shipped with the terminal. 2. Carefully drill 5.56 mm (7/32 in.) holes for studs as indicated. 3. Install the mounting studs (Cat. No. 2711-NP3) using a 7/32-inch socket on the end of the stud. 4. Turn stud clockwise and tighten to approximately 1.13 Nm (10 in.-lb).
Chapter 11 Installing the PV1400 Terminal 7. Install the self-locking nuts hand tight. Tighten mounting nuts to a torque of 1.13 Nm (10 lb-in.) to provide a proper seal and prevent potential damage to the terminal. Allen-Bradley assumes no responsibility for water or chemical damage to the terminal or other equipment within the enclosure because of improper installation. A properly installed terminal has a small gap between the bezel and enclosure. ATTENTION 8.
Chapter 12 Terminal Connections Chapter Objectives This chapter describes network and device connections for PanelView terminals.
Chapter 12 Terminal Connections Cable Charts Refer to the following charts for a summary of PanelView terminal connections to controllers and network interface modules.
Terminal Connections Protocol Chapter 12 PanelView Standard Comm Port Cables: PanelView to Processor SLC-500, 5/01, 5/02 CH1 RJ45 (DH-485) SLC-5/03, 5/04, 5/05 CH0 (9-pin RS-232) (DF1 or DH-485) SLC 5/03 CH1 (RJ45) (DH-485) SLC 5/04 CH1 (DH+) SLC 5/05 CH1 (ENET) DeviceNet xxx10 DeviceNet Communication Port PanelView 300 - 1400 2711-xxx10 to SLC 5/02 with 1747-SDN and DeviceNet cable use 1747-SDN Module with DeviceNet cable ControlNet xxx15 ControlNet Communication Port PanelView 550T - 1400 271
Chapter 12 Protocol Terminal Connections PanelView Standard Comm Port Cables: PanelView to Processor PLC-5, PLC-5C, PLC-5E CH0 (25-pin RS-232) (DF1) ControlLogix CH0 (9-pin RS-232) (DF1) MicroLogix 1000, 1200, 1500LSP CH0 (8-pin Mini DIN) (DF1 or DH-485) RS-232 (DF1) Comm Port (8-pin Mini Din) PanelView 300 Micro 2711-xxx18 1761-CBL-AP00 (1.5 ft/0.5 m) 1761-CBL-PM02 (6.5 ft/2 m) 2711-CBL-PM05 (16 ft/5 m) 2711-CBL-PM10 (32 ft/10 m) (9-to-25 pin adapter required) 1761-CBL-AP00 (1.5 ft/0.
Terminal Connections Protocol PanelView Standard Comm Port Chapter 12 Cables: PanelView to Processor PLC-5, PLC-5C, PLC-5E CH0 (25-pin RS-232) (DF1) ControlLogix CH0 (9-pin RS-232) (DF1) MicroLogix 1000, 1200, 1500LSP CH0 (8-pin Mini DIN) (DF1 or DH-485) EtherNet/IP Ethernet Communication Port xxx20 PanelView 550T - 1400 2711-xxx20 to PLC-5E with Ethernet cable Use 1756-ENET Module with Ethernet cable Use 1761-NET-ENI Module with Ethernet cable Remote I/O xxx1 Remote I/O Communication Port Panel
Chapter 12 Protocol DF1 xxx16 xxx17 xxx18 DH-485 xxx2 xxx3 xxx5 xxx9 xxx19 Terminal Connections PanelView Standard Comm Port Cables: PanelView to Processor MicroLogix 1500LRP CH1 (9-pin RS-232) (DF1 or DH-485) CompactLogix CH0 (9-pin RS-232) (DF1 or DH-485) FlexLogix CH0 (9-pin RS-232) (DF1) RS-232 (DF1) Comm Port (8-pin Mini Din) PanelView 300 Micro 2711-xxx18 1761-CBL-AP00 (1.5 ft/0.5 m) 1761-CBL-PM02 (6.5 ft/2 m) 2711-CBL-PM05 (16 ft/5 m) 2711-CBL-PM10 (32 ft/10 m) 1761-CBL-AP00 (1.5 ft/0.
Terminal Connections Chapter 12 Runtime Communication Cables - to Network Interface Module Protocol DF1 xxx16 xxx17 xxx18 DH-485 xxx2 xxx3 xxx5 xxx9 xxx19 PanelView Standard Comm Port Cables: PanelView to Interface Module 1747-AIC 1761-NET-AIC RS-232 (DF1) Comm Port (8-pin Mini Din) PanelView 300 Micro 2711-xxx18 N/A 1761-CBL-AP00 (1.5 ft/0.5 m) 1761-CBL-PM02 (6.5 ft/2 m) 2711-CBL-PM05 (16 ft/5 m) 2711-CBL-PM10 (32 ft/10 m) 1761-CBL-AM00 (1.5 N/A ft/0.5 m) 1761-CBL-HM02 (6.
Chapter 12 Terminal Connections Application File Upload/Download (Direct) Cables PanelView Standard Type Cable to Personal Computer PanelView 300 Micro 2711-M3A18L1, -M3A19L1 1761-CBL-PM02 (6.
Terminal Connections Remote I/O Terminal Connections Chapter 12 This section describes connections for the remote I/O PanelView terminals including: • remote I/O port. • supported controllers. • making remote I/O connections. • remote I/O pass-through. Remote I/O Terminal Ports The remote I/O versions of the PanelView terminal (catalog numbers ending in 1) have a remote I/O port and an RS-232 port. Use the remote I/O port to: • communicate with the remote I/O scanner port on a PLC controller.
Chapter 12 Terminal Connections Supported Controllers The remote I/O terminal connects to any Allen-Bradley 1771 remote I/O link. Applicable host controllers include almost all Allen-Bradley PLCs, computers, VME controllers, and DEC Q-Bus controllers with a remote I/O scanner module. New PLC product releases that support 1771 remote I/O will also work with PanelView.
Terminal Connections Chapter 12 Making Remote I/O Connections To connect a PanelView terminal to a remote I/O scanner, use cable Catalog No. 1770-CD (equivalent to Belden 9463). The maximum cable length (link distance) is determined by the communication rate. • 2,800 m (10,000 ft) for 57.6K baud • 1,400 m (5,000 ft) for 115.2K baud • 700 m (2,500 ft) for 230.4K baud See Programmable Controller Wiring and Grounding Guidelines, publication 1770-4.1.
Chapter 12 Terminal Connections Remote I/O Pass-through using DH+ Remote I/O terminals allow the transfer of applications from a computer on the Allen-Bradley DH+ link to a PLC-5 or SLC-5/04 controller. The controller passes data to the PanelView terminal over the remote I/O network. PLC-5 DH+ Computer Remote I/O Pass-through Remote I/O Network PanelView Follow these steps to transfer an application using remote I/O pass-through: 1.
Terminal Connections Chapter 12 7. Refer to the online help in the PanelBuilder32 software for procedures on how to transfer applications by using pass-through. TIP If the terminal is the last device on the link, connect a 1/2 watt terminating resistor across terminals 1 and 2. The value of the resistor depends on the DH+ baud rate: • for 57.6 kilobaud and 115.
Chapter 12 Terminal Connections Use the RS-232 port to: • transfer PanelView applications between a computer and the DH+ terminal using a direct connection. • connect a printer. For connection details, see the last section in this chapter.
Terminal Connections Chapter 12 Making DH+ Connections Use the Belden 9463 twin axial cable (1770-CD) to connect a DH+ PanelView terminal to the DH+ link. You can connect a DH+ link in 2 ways. • trunk line/drop line - from the drop line to the connector screw terminals on the DH+ connectors of the processor • daisy chain - to the connector screw terminals on the DH+ connectors on the processor Follow these guidelines when installing DH+ communication links.
Chapter 12 Terminal Connections DH-485 Terminal Connections This section describes connections for the DH-485 PanelView terminals. • • • • • DH-485 terminal ports Connecting to a single SLC controller (Point-to-point) Connecting to a DH-485 network Connecting a computer Connecting a Hand-held terminal TIP For PanelView 300 Micro terminals, refer to page 218. DH-485 Terminal Ports (RJ45) DH-485 PanelView terminals with catalog numbers ending in 2 have two DH-485 ports.
Terminal Connections Chapter 12 The DH-485 communication port and programming connector may appear in different locations on specific terminals. Identify the ports by their size and shape or by the port labels. RS-232 Printer Port DH-485 Communication Port RS-232 Printer Port DH-485 SLC Programming Port DH-485 Communication Port DH-485 SLC Programming Port Connecting to a Single SLC Controller (Point-to-point) To connect a DH-485 terminal to a single SLC controller use one of these cables: • 0.
Chapter 12 Terminal Connections The DH-485 connectors are not electrically isolated. If electrical isolation is required, use Link Couplers (Cat. No. 1747-AIC) as shown on next page. Electrical isolation using Link Couplers (Cat. No. 1747-AIC) is required where the distance between the PanelView terminal and the SLC is greater than 6.1 m (20 ft).
Terminal Connections Chapter 12 The illustration below shows how to connect a DH-485 terminal to a MicroLogix or SLC controller using the AIC+ Link Coupler (Cat. No. 1761-NET-AIC). AIC+ 1761-NET-AIC PanelView 1000 MicroLogix 1000, 1200, 1500LSP Cable Cat. No. 1761-CBL-AS03 Cat. No. 1761-CBL-AS09 Cat. No. 1761-CBL-HM02 1761-CBL-AM00 SLC 5/03, 5/04, 5/05 AIC+ 1761-NET-AIC PanelView 1000 Cable Cat. No. 1761-CBL-AS03 Channel 0 Port Cat. No.
Chapter 12 Terminal Connections Connecting a Computer On DH-485 terminals, PanelView applications are transferred: • through the DH-485 programming connector to the terminal. • through any node on a DH-485 network. To connect a computer to the PanelView terminal, you need: • a cable (same cables used to transfer applications from APS software to SLC) – 0.3 m (1 ft) cable, Cat. No. 1747-C11 – 1.83 m (6 ft) cable, Cat. No. 1747-C10 – 6.1 m (20 ft) cable, Cat. No.
Terminal Connections Chapter 12 Connecting a Computer to DH-485 Connector Using a Power Supply PanelBuilder32 PanelView 1000 Wallmount Power Supply Cat. No. 1747-NP1 To DH-485 Programming Connector 25-pin to 9-pin Adapter (if required) Personal Computer Interface Converter (Cat. No. 1747-PIC) To DH-485 Communication Port Cable Cat. No. 1747-C10 Cat. No. 1747-C11 Cat. No.
Chapter 12 Terminal Connections Connecting a Hand-held Terminal To connect a Hand-held Terminal (HHT) to the PanelView terminal, use cable Cat. No. 1747-C10. One end of the cable connects to the HHT connector and the other end connects to the DH-485 programming connector on the terminal. All power is supplied to the HHT through the cable. IMPORTANT The PanelView terminal must be connected to an SLC, DH-485 network, or power supply. This connection provides power for the HHT.
Terminal Connections RS-232 (DH-485) Terminal Connections Chapter 12 This section describes connections for the RS-232 (DH-485) PanelView terminals including: • RS-232 ports • connecting to a SLC, CompactLogix, or MicroLogix Controller (point-to-point) • connecting to a MicroLogix Controller through the AIC+ module • connecting a computer • connecting to a DH-485 link Refer to page 218 for PanelView 300 Micro RS-232 connections.
Chapter 12 Terminal Connections Connecting to an SLC, CompactLogix, MicroLogix Controller (Point-to-point) This section shows how to connect a CompactLogix, MicroLogix 1500LRP, or SLC controller (SLC 5/03, SLC 5/04, or SLC 5/05) to the RS-232 PanelView terminal for point-to-point (DH-485) communication. On terminals with two ports, use the RS-232 communication port. For the SLC, CompactLogix or MicroLogix 1500LRP controller, use one of these cables: • 5 m (16.4 ft) Cat. No. 2711-NC13 • 10 m (32.7 ft) Cat.
Terminal Connections Chapter 12 Connecting to a MicroLogix Controller through an AIC+ Module This section shows how to connect the RS-232 (DH-485) version of the PanelView terminal to a MicroLogix controller through an AIC+ Link Coupler. AIC+ Cat. No. 1761-NET-AIC MicroLogix 1000, 1200, 1500LSP Belden Cable 9842 Catalog No. 1761-CBL-HM02 1761-CBL-AM00 Catalog No. 1747-CP3 RS-232 Communication Cables Cable, Cat. No. 2711-NC13 Cable, Cat. No. 2711-NC14 Cable, Cat. No.
Chapter 12 Terminal Connections Connecting a DH+ to DH-485 Pass-through Link This section shows connections for transferring applications between a computer on the Allen-Bradley DH+ link and an RS-232 (DH-485) PanelView terminal, through an SLC 5/04 controller. The RS-232 (DH-485) communication port on the terminal connects to the CH0 port of the controller using one of the cables listed below.
Terminal Connections Chapter 12 Compatible Controllers The RS-232 (DF1) terminals support full duplex communication with the following controllers. • MicroLogix 1000, 1200, 1500 controllers via the communication port. • ControlLogix, CompactLogix, FlexLogix controller via RS-232 port • SLC, PLC or MicroLogix 1000, 1200 or 1500 controllers via 1761-Net-DNI modules (for DeviceNet Network). • SLC 5/03, SLC 5/04, or SLC 5/05 controllers via Channel 0/DF1 port.
Chapter 12 Terminal Connections RS-232/DF1 Port Connector The DF1 port on the PanelView terminal is a 9-pin, male, RS-232 connector. The table below shows the pinout descriptions for this port and how these pins map to the DF1 ports on the controllers. DF1 Port 9-pin DCE SLC PLC 9-pin 25-pin MicroLogix/ DNI 8-pin DIN 1 2 RXD 2 3 4 3 TXD 3 2 7 4 DTR 4 20 5 COM 5 7 6 DSR 6 6 7 RTS 7 4 8 CTS 8 5 2 9 The maximum cable length for DF1/full duplex communication is 15.
Terminal Connections Chapter 12 Connecting to an SLC, PLC, or MicroLogix 1500LRP Controller The following shows a point-to-point connection between the DF1 port of the PanelView terminal and an SLC or PLC controller. PanelView SLC 5/03, 5/04, 5/05 MicroLogix 1500LRP DF1 Port 2711-NC13, -NC14 Cable DF1 Port PLC 5 2711-NC13, -NC14 Cable 9 to 25-Pin Adapter DF1 Port Use an optical isolator or equivalent when grounding level differences exist between the controller or modem and the PanelView.
Chapter 12 Terminal Connections Using a Modem Wire or radio modem communication is possible between a DF1 terminal and controller. Each modem must support full duplex communication. Refer to your modem user manual for details on settings and configuration.
Terminal Connections Chapter 12 Constructing a Null Modem Cable To construct a null modem cable, refer to the following pinout: 9-pin ControlNet Connections 25-pin 9-pin 3 3 3 2 2 2 5 7 5 1 8 1 4 20 4 6 6 6 8 5 8 7 4 7 This section describes connections for the ControlNet PanelView terminals including: • • • • • ControlNet Protocol Compatible ControlNet Controllers ControlNet ports on the PanelView terminal Typical ControlNet network Making ControlNet connections Related Info
Chapter 12 Terminal Connections ControlNet Protocol The PanelView terminal supports release 1.5 of ControlNet. Scheduled and Unscheduled PLC-5C and ControlLogix messaging. Redundant cabling is supported. ControlNet allows a flexible control architecture that can work with multiple processors and up to 99 nodes (via taps) anywhere along the trunk cable of the network. There is no minimum tap separation and you can access the ControlNet network from every node (including adapters).
Terminal Connections Chapter 12 Typical ControlNet Network Below is a typical ControlNet network with a PanelView terminal installed on a network drop.
Chapter 12 Terminal Connections Making ControlNet Connections Use the pinout information below to connect the PanelView to a ControlNet network. IMPORTANT Follow the ControlNet network layout and design as specified in the ControlNet Cable System Planning and Installation Manual, publication CNET-IN002.
Terminal Connections Chapter 12 NAP and Redundant Cables ControlNet cables, taps, connectors. Refer to the ControlNet Cable System Planning and Installation manual, publication CNET-IN002 for descriptions of these components. For information on purchasing these items, refer to the Allen-Bradley ControlNet Cable System Component List, publication AG-PA002.
Chapter 12 Terminal Connections DeviceNet Network Terminal Connections This section describes connections for the DeviceNet PanelView terminals including: • DeviceNet connectors • connections • typical DeviceNet network DeviceNet Terminal Ports The DeviceNet versions of the PanelView terminals (catalog numbers ending in 10) have a DeviceNet port and an RS-232 serial port. • Use the DeviceNet port to connect to devices on a DeviceNet network or transfer applications over a DeviceNet network.
Terminal Connections Chapter 12 Making DeviceNet Connections Use one of the cables below to connect the DeviceNet version of the PanelView terminal to a DeviceNet network. Cable Publication No.
Chapter 12 Terminal Connections Typical DeviceNet Network Below is a typical DeviceNet network with PanelView terminals installed on 2 of the network drops. A DeviceNet network requires a 24V DC power supply. DeviceNet power consumption is 24…90 mA @24V DC. The PanelView terminal does not receive its power from the network. PLC-5 SLC 5/04 or DeviceNet Scanner Module (Cat. No. 1747-SDN) DeviceNet Scanner Module (Cat. No.
Terminal Connections EtherNet/IP Connections Chapter 12 The EtherNet/IP PanelView terminal can communicate on an EtherNet TCP/IP network with the following devices: • PLC-5E or PLC-5 with 1761-NET-ENI or 1785-ENET module • SLC-5/05 or SLC with 1761-NET-ENI module • ControlLogix controller with 1756-ENET/B or 1761-NET-ENI module • MicroLogix, CompactLogix, or FlexLogix with 1761-NET-ENI module • Another EtherNet/IP PanelView terminal • Any device that can process CIP messages The PanelView terminal suppor
Chapter 12 Terminal Connections Ethernet Connector The Ethernet connector is an RJ45, 10/100Base-T connector. This is the pinout for the connector. Pin RJ45 Connector 8 1 Pin Pin Name 1 TD+ 2 TD- 3 RD+ 4 NC 5 NC 6 RD- 7 NC 8 NC When to use a straight-through and cross-over pin-out: • Direct point-to-point 10/100Base-T cables, with cross over pin-out (1-3, 2-6, 3-1, 6-2), connect the PanelView Ethernet port directly to another SLC 5/05 Ethernet port (or a computer 10/100Base-T port).
Terminal Connections Chapter 12 Typical EtherNet/IP Configuration The following illustration shows a ControlLogix Controller (with 1756-ENET/B modules), a PLC-5E controller, SLC 5/05, a MicroLogix/CompactLogix/FlexLogix (with 1761-NET-ENI module), and an Ethernet PanelView terminal connected to an EtherNet/IP network. Note that each node has a unique IP address. MicroLogix, FlexLogix, or CompactLogix with 1761-NET-ENI Module PLC-5E Controller ControlLogix 5550 Controller SLC 5/05 10.0.0.
Chapter 12 Terminal Connections PanelView 300 Micro Terminal Connections This section describes how to connect the PanelView 300 Micro terminal.
Terminal Connections Chapter 12 Connecting to an SLC, PLC-5, ControlLogix, MicroLogix 1500LRP, CompactLogix, or FlexLogix Directly connect the PanelView 300 Micro terminal to an SLC, PLC-5 ControlLogix, MicroLogix 1500LRP, CompactLogix, or FlexLogix processor using the following cables. Use DH-485 (SLC only) or DF1 protocols for communication.
Chapter 12 Terminal Connections Connecting to an Advanced Interface Converter DH-485 versions of the PanelView 300 Micro can operate on a DH-485 network through an Advanced Interface Converter (AIC+) module. Use the following cables. AIC+ PanelView 300 Micro 1761-CBL-PM02, 2711-CBL-PMxx (to Port 1 of AIC+) 1761-CBL-HM02, 2711-CBL-HMxx (to Port 2 of AIC+) RS-232 Communication Port 1 2 5 4 3 8 7 6 1761-CBL-AP00 (to Port 1) 1761-CBL-AM00 (to Port 2) 5 Cable, Catalog No. 1761-CBL-AM00, Series C (.
Terminal Connections Chapter 12 Connecting to a Personal Computer (Application File Transfers) Transfer applications between a computer and PV300 Micro terminal using one of the following cables. TIP Applications for the PanelView 300 Micro terminal are developed using PanelBuilder32 Software (Catalog No. 2711-ND3, V3.60 or later). PanelView 300 Micro Personal Computer (Running PanelBuilder32) 1761-CBL-PM02 2711-CBL-PM05 2711-CBL-PM10 RS-232 Communication Port 1 2 Cable, Catalog No.
Chapter 12 Terminal Connections PanelBuilder32 Software Supports the direct transfer of application files from PanelBuilder32 using an RS-232 link. Windows PanelView File Transfer (WinPFT) Utility Supports the direct transfer of PanelBuilder32 application files from WinPFT over an RS-232 link. The WinPFT utility is included with the PanelBuilder32 Software. RSLinx software may be required to transfer applications to the terminal for DH-485 and DF1 protocols.
Terminal Connections Connecting a Computer or Printer to the Terminal Chapter 12 Most of the PanelView terminals have an RS-232 serial port to: • download/upload applications over a serial link. • connect a printer that supports the IBM enhanced character set. PanelView terminals that don’t have an additional RS-232 Printer Port include the 300 Micro, the 300 (except for DeviceNet), and the -xxA2/ -xxA5 versions of the 550/600 and 900 monochrome terminals.
Chapter 12 224 Terminal Connections Publication 2711-UM014G-EN-P - September 2008
Chapter 13 Troubleshooting and Maintenance Chapter Objectives This chapter tells how to isolate and correct common operating problems and perform routine maintenance tasks. • • • • • • Using required equipment Using troubleshooting chart Interpreting status indicators Cleaning display window Replacing clock module Replacing backlight TIP You cannot access the PanelView 300 Micro terminal's internal components. The rear cover is not removable; do not attempt to remove the cover.
Chapter 13 Troubleshooting and Maintenance Troubleshooting Chart Problem Probable Causes Terminal does not power up. Improper connection to power source. Corrective Actions Verify wiring and connections to power source. Incorrect input voltage level. Verify correct voltage is present at power terminals. The dc power wires reversed (dc terminals only). Make sure dc power positive and negative are connected to the proper terminals. Power terminal block not fully seated (PV300 terminals only).
Troubleshooting and Maintenance Chapter 13 Troubleshooting Chart Problem Probable Causes Corrective Actions Clock Module Battery Low message is displayed. Internal parameters corrupt. Reload application and cycle power to the terminal. Clock module battery failure. Replace clock module as described in instructions provided with clock module kit. For PanelView 300 Micro, clock module cannot be replaced. Cannot transfer application from memory card. Memory card is not properly installed.
Chapter 13 Troubleshooting and Maintenance Troubleshooting Chart Problem Probable Causes Corrective Actions Values do not update on display but appear as asterisks **** Terminal is not communicating with controller. Check status of COMM Status indicator. Can’t enter Configuration Mode when pressing Left and Right arrow keys simultaneously. (1) 228 Refer to problem No communication with SLC or PLC controller for more details. Value is invalid or exceeds the field width defined for the object.
Troubleshooting and Maintenance Interpret Status Indicators Chapter 13 On PanelView terminals (except PanelView 300 Micro), use the COMM and Fault Status indicators to isolate operating problems. The illustration below shows the location of these indicators on some terminals. See Chapter 1 for status indicator locations on other terminals.
Chapter 13 Troubleshooting and Maintenance Remote I/O Status Indications Status Indicator This pattern Indicates Comm(1) Solid Fill Normal operating state (no communication faults) No Fill Communication not functioning • Verify that baud rate and rack settings match the PLC settings • Verify proper terminal to controller connections • Verify that the PLC enables remote I/O communication Fault (1) Blinking No communication established. PLC is in program mode.
Troubleshooting and Maintenance Clean the Display Window Chapter 13 Follow these steps to clean the display window. ATTENTION Use of abrasive cleansers or solvents may damage the window. Do not scrub or use brushes. 1. Disconnect power from the terminal at the power source. 2. Use a clean sponge or a soft cloth to clean the display with a mild soap or detergent. 3. Dry the display with a chamois or moist cellulose sponge to avoid water spots.
Chapter 13 Troubleshooting and Maintenance Replace the Clock Module The real-time clock (RTC) module contains a lithium battery used only by the real-time clock. The battery is not used for application backup or input retention. The clock module has a typical life expectancy of seven years. TIP The real-time clock on the PanelView 300 Micro terminal is not replaceable. The clock module replacement kits for the PanelView terminals are listed on page 56 under Replacement Parts.
Appendix A Specifications PanelView 300 Micro Terminal Electrical DC Power Supply Voltage Limits Power Consumption 11…30V DC (24V nominal), Class 2 Power Supply 2.5 W maximum (0.105A @24V DC) Mechanical Enclosure NEMA Type 12/13, 4X (Indoor use only), IP54, IP65 Weight 284 g (10 oz.) Dimensions mm inches 133 (H) x 112 (W) x 48 (D) 5.23 (H) x 4.38 (W) x 1.87 (D) Installed Depth 35mm (1.39 in.
Appendix A Specifications Character Sizes (Pixel size = 0.48 x 0.48 mm) Size in Pixels width x height) Characters/Row Maximum Rows Dimensions in mm Width x Height 4x6 31 10 1.9 x 2.9 6x8 20 7 2.9 x 3.8 6 x 16 20 3 2.9 x 7.7 6 x 24 20 2 2.9 x 11.5 12 x 8 10 7 5.8 x 3.8 12 x 16 10 3 5.8 x 7.7 12 x 24 10 2 5.8 x 11.5 18 x 8 6 7 8.6 x 3.8 18 x 16 6 3 8.6 x 7.7 18 x 24 6 2 8.6 x 11.
Specifications Appendix A Display Type Liquid Crystal Display (LCD) with integral LED backlight (100,000 hour life) Size 73 mm (w) x 42 mm (h) 2.87 in. (w) x 1.67 in.
Appendix A Specifications PanelView 550 Terminals Electrical DC Power Supply Voltage Limits Power Consumption Supply Voltage Limits (touch screen only) Power Consumption (touch screen only) 18…30V DC (24V DC nominal) 18 W, max (0.75 A @ 24V DC) 18…32V DC (24V DC nominal) 18 W, max (0.
Specifications Appendix A Terminal Memory PV550 (Series E or later) or PV550T (Series A or later) Total Application Flash Memory 240K bytes (application screens) PV550 (Prior to Series E) Total Application Flash Memory 112K bytes (application screens) Environment Operating Temperature 0…55 ° C (32…131 ° F) Storage Temperature -20…70 ° C (-4…158 ° F) Relative Humidity (non-condensing) 5…95% at 0…30 ° C (32…86 ° F) 5…75% at 31… 40 ° C (88…104 ° F) 5…50% at 41…55 ° C (106…131 ° F) Heat Dissipation
Appendix A Specifications PanelView 600 Color Keypad and Touch Terminals Electrical AC Power Supply Voltage Limits Power Consumption 85…264V AC, 43…63 Hz 60 VA maximum DC Power Supply Voltage Limits Power Consumption 18…32V DC (24V DC nominal) 24 W max. (1.0A @ 24V DC) Mechanical Enclosure NEMA Type 12/13, 4X (Indoor use only), IP54, IP65 Status Indicators COMM Fault Green Red Weight 2 kg (4.4 lb) Dimensions mm in 192 (H) x 290 (W) x 116 (D) 7.55 (H) x 11.40 (W) x 4.
Specifications Appendix A Character Sizes (Pixel size = 0.36 x 0.37 mm) PanelView 600 Color Touch Only Terminals Size in Pixels width x height) Characters/Row Maximum Rows Dimensions in mm Width x Height 6x9 52 25 2.9 x 5.9 8 x 16 39 14 2.9 x 5.9 8 x 24 39 9 2.9 x 8.9 16 x 24 19 9 5.8 x 8.9 24 x 32 13 7 8.6 x 11.8 32x 40 9 5 11.5 x 14.8 Electrical DC Power Supply Voltage Limits Power Consumption 18…32V DC (24V DC nominal) 24 W max (1.
Appendix A Specifications Terminal Memory Total Application Flash Memory 240K bytes (application screens) Environment Operating Temperature 0…50 ° C (32…122 ° F) Storage Temperature -25…70 ° C (-13…158 ° F) Relative Humidity (non-condensing) 5…95% at 0…40 ° C (32…104 ° F) Heat Dissipation 17 W (577 BTU/HR) Shock (operating/non-operating) 15 g/30 g Vibration (operating) 2 g up to 2,000 Hz Character Sizes (Pixel size = 0.35 x 0.
Specifications Appendix A Mechanical Enclosure NEMA Type 12/13, 4X (Indoor use only) IP54, IP65 Status Indicators COMM Fault Green Red Weight - PV900M Keypad Touch Screen 3.14 kg (4.4 lb) 2.91 kg (6.4 lb) Weight - PV900C Keypad Touch Screen 3.18 kg (7.0 lb) 2.95 kg (6.5 lb) Dimensions - PV900M/900C Keypad mm in 249 (H) x 406 (W) x 112 (D) 9.80 (H) x 15.97 (W) x 4.40 (D) Dimensions - PV900M/900C Touch Screen mm in 249 (H) x 336 (W) x 112 (D) 9.80 (H) x 13.24 (W) x 4.
Appendix A Specifications Terminal Memory PV900M (prior to Series E) Total Application Flash Memory 240K bytes (application screens) PV900M (Series E, firmware 3.
Specifications Appendix A Character Sizes PV900C (Pixel size = 0.27 x 0.27 mm) Publication 2711-UM014G-EN-P - September 2008 Size in Pixels width x height) Characters/Row Maximum Rows Dimensions in mm Width x Height 8 x 16 79 24 2.2 x 4.3 8 x 24 79 19 2.2 x 6.5 16 x 24 39 19 4.3 x 6.5 24 x 32 26 14 6.5 x 8.6 32x 40 19 11 8.6 x 10.
Appendix A Specifications PanelView 1000 Color & Grayscale Electrical AC Power - PV1000G and PV1000C Supply Voltage Limits Power Consumption 85…264V AC, 47…63 Hz 55 VA maximum DC Power - PV1000G and PV1000C Supply Voltage Limits Power Consumption 18…32 V DC (24V DC nominal) 24 W max (1.0A @ 24V DC) Mechanical Enclosure NEMA Type 12/13, 4X (Indoor use only) IP54, IP65 Status Indicators COMM Fault Green Red Weight - PV1000G and PV1000C Keypad Touch 3.06 kg (6.7 lb) 3.00 kg (6.
Specifications Appendix A Display Pixels 640 x 480 Touch Cells 384 (24 columns x 16 rows) Touch Cell Size 26 x 30 pixels Environment Operating Temperature 0…55 ° C (32…131 ° F) Storage Temperature -25…70 ° C (-13…158 ° F) Relative Humidity (non-condensing) 5…95% at 0…55 ° C (32…131 ° F) Heat Dissipation 39 W (132 BTU/HR) for Grayscale and Color Shock (operating/non-operating) 15 g/30 g Vibration (operating) 2 g up to 2,000 Hz Character Sizes PV1000G and 1000C (Pixel size = 0.33 x 0.
Appendix A Specifications Mechanical Dimensions - PV1400 Keypad mm inches 355 (H) x 483 (W) x 394 (D) 13.97 (H) x 19.0 (W) x 15.53 (D) Dimensions - PV1400 Touch Screen mm in 355 (H) x 441 (W) x 394 (D) 13.97 (H) x 17.37 (W) x 15.53 (D) Installed Depth 370 mm (14.58 in.) 400 mm (15.75 in.) with clearance to insert and remove memory card Terminal Memory Total Application Flash Memory 1008K bytes (application screens) Display Type Color CRT Size 255 x 191 mm (10.0 x 7.5 in.
Specifications Appendix A Communication DH-485 Network Communication Rate Distance Maximum 1200, 2400, 9600, 19.2K 1219 m (4,000 ft) DH+ Network Communication Rate Distance Maximum 57.6K, 115.2K, 230.4K 3048 m (10,000 ft) RS-232 or DH-485 Point-to-Point Communication Rates Distance Maximum 1200, 2400, 9600, 19.2K 6.1 m (20 ft) Remote I/O Communication Rates Publication 2711-UM014G-EN-P - September 2008 57.6K, 2,800 m (10,000 ft) 115.
Appendix A Specifications Agency Certifications 300 Micro 300 550 600 900M 900C 1000G 1000C 1400 Emissions (Class A: Industrial) EN50081-2:1993 x x x x x x x x x Immunity (Industrial) EN61000-6-2:1999 x x(1) x(1) x(1) x(1) x(1) x(1) x(1) x(1) Immunity (Industrial) EN50082-2:1995(2) x x x x x x x x Programmable Controllers Equipment Requirements and Tests) EN61131 2:1995 x x x x x x x x x x(3) x x x x x x Low Voltage Directive (Safety Sections of EN6113
Appendix B Messages, Codes and Self-test Numbers This appendix lists: • terminal messages and codes that may appear during terminal operation. • description of self-test numbers. Types of Terminal Messages The terminals have different messages to display. Status Messages Indicate the terminal is performing an operation that may limit access to the terminal, such as an application download or a communication problem.
Appendix B Messages, Codes and Self-test Numbers General Terminal Messages Error Number Type Meaning A fault has 200-206, 300, occurred. Error = 318-321, 328, X 329, 331, 346, 347, 355, 356, 358, 367, 404, 411, 416, 417, 421-425, 447-449, 457, 459, 700, 1105, 1111, 1113, 1115, 1207-1211, 2002-2009, 2016, 2018, 2021, 2028 and 2029 Minor Fault or Terminal Fault A minor fault was detected that could Press any key to recover from a minor impact terminal operation or a fault.
Messages, Codes and Self-test Numbers Error Number Terminal Messages 315 Type Appendix B Meaning Recommended Action Unformatted card Reminder Memory card is unformatted, contains an unrecognizable format or is corrupt. Reformat the card or replace it with a new card if corrupt. Try again. 316 Write Protected Card A write command to the card failed because the card switch is in the protected mode. Select write mode by changing the switch on the top edge of the card. Try again.
Appendix B Messages, Codes and Self-test Numbers Error Number Terminal Messages Type Meaning Recommended Action 341 Proceed with download? Warning You pressed [F2], Restore From Card on the Memory Card configuration screen. Enter appropriate response: 0 or F1 to abort 0 or F1 -Abort 1 or F2 to continue 1 or F2 - Continue 342 The PVA File exists. Reminder / File Transfer Status You pressed [F3], Save To Card on the Memory Card configuration screen when the file exists on the card.
Messages, Codes and Self-test Numbers Appendix B Error Number Terminal Messages Type Meaning Recommended Action 436 Logic Controller has screen control Reminder You tried to change the application screen but it is configured for controller only access. No action required, controller will change screens as programmed. 634 Read Fail or Write Fail Status ControlLogix Tag or address does not exist or is the wrong data type. Check tag address. Check for data type mismatch.
Appendix B Messages, Codes and Self-test Numbers Error Number Terminal Messages Type Meaning Recommended Action 2011 Retained memory Reminder lost. Presets were loaded. The battery backed memory was invalid during startup. The system defaulted to preset values instead of the last states. No action necessary. Terminal reverts to defaults. 2012 Application file: Too many retained memory devices Terminal Fault The battery-backed RAM is too full to hold all devices requiring presets.
Messages, Codes and Self-test Numbers Appendix B ControlNet Terminal Messages See Terminal Codes for messages below Error Number Terminal Messages 634 Type Meaning Recommended Action PanelView offline Comm Warning PanelView is offline. Check connections 634 Write fail. Comm Warning PanelView is communicating with the Check / define data table address in controller. The data table address the controller. does not exist. 634 Write timeout.
Appendix B Messages, Codes and Self-test Numbers Remote I/O Terminal Messages Error Number Terminal Messages Type Meaning Recommended Action 661 Timeout - No Block Transfer Writes Comm Status The PLC is communicating with the terminal, but the PanelView is not receiving BTW requests required by the application. Check ladder logic for missing BTW instructions (instructions are not enabled) or addressing errors. Check for logic controller errors.
Messages, Codes and Self-test Numbers Appendix B DH+ Terminal Messages Error Number Terminal Messages Type 675 or 684 Required network Comm Status node(s) not found 676 or 685 File access error Comm Status Meaning Recommended Action The network is active, but the logic controller(s) are not located at the expected nodes. Verify that the logic controller(s) required by the application are at the expected node addresses and that the communication parameters are set properly. 1.
Appendix B Messages, Codes and Self-test Numbers DF1 Terminal Messages Error Number Terminal Messages 675 or 682 Meaning Recommended Action Required network Comm Status node(s) not found The network is active, but the logic controller(s) are not located at the expected nodes. Verify that the logic controller(s) required by the application are at the expected node addresses and that the communication parameters are set properly.
Messages, Codes and Self-test Numbers Appendix B DeviceNet Comm Status Code Indicates Recommended Action 1 No connections established. Occurs on power-up until a device connection is established on the network. Establish a connection over DeviceNet to the PanelView. 2 A connection is in the timed out state. Occurs when I/O polling stops after an I/O poll connection is running. Check that the network wiring and that the master device (scanner) is operational. 3 An peer tag cannot be obtained.
Appendix B Messages, Codes and Self-test Numbers Alert codes appear as a box in the middle of the screen. Error 636 appears in the upper left corner. Operation of the terminal continues. Alert messages can be cleared. DeviceNet Alert Codes Indicates Recommended Action 2 Unsupported DeviceNet Message received. The Network Access Object received a message that is not supported. Should not occur in normal operation. Clear the message. If problem re-occurs, contact technical support.
Messages, Codes and Self-test Numbers Appendix B DeviceNet Alert Codes Indicates Recommended Action 20 Autobaud Failure. The autobaud process failed to detect a valid baud rate within 10 seconds. Occurs if network traffic is nonexistent or intermittent. Start the terminal when network traffic exists or use a fixed baud rate. 23 Nonvolatile Objects have been reset. Nonvolatile storage of some objects required a full reset on powerup. Certain nonvolatile values will be reset to defaults.
Appendix B Messages, Codes and Self-test Numbers General Codes General Terminal Alert Code Alert Type Indicates Recommended Action 603 Critical fault File download error Reset the terminal. If problem occurs again, contact technical support. 9020 Critical fault An internal fault occurred. Reset the terminal. If problem occurs again, contact technical support. ControlNet Codes These errors appear at the top of the application screen or on the terminal’s configuration screen.
Messages, Codes and Self-test Numbers Appendix B These messages appear on the terminal screen as DC Error=xx. If you get an alert number that is not listed here, contact technical support. ControlNet Alert Codes Alert Type Indicates: Recommended Action 9000 Critical fault Interface startup failed. Contact technical support. 9003 Critical fault CIP S/N is not valid. Contact technical support. 9004 Critical fault Out of buffers. Contact technical support.
Appendix B Messages, Codes and Self-test Numbers Error Number Terminal Messages Type Meaning Recommended Action xx,xx,xx Communication Interface Fault Critical Fault A hardware problem was detected during power-up. If you ignore message and display the EtherNet/IP Communication Screen, the Comm Status displays “Comms hardware fault:” without an error number. The FW revision, serial number and EtherNet/IP address fields are displayed. Contact technical support to have unit repaired.
Messages, Codes and Self-test Numbers Appendix B Error Number Terminal Messages Type Meaning Recommended Action 16398 The Connection Originator is indicating it is in Program Mode Comm Warning The logic controller is offline (in Program Mode). The COMM Status indicator on the Configuration Mode menu is off. Place the logic controller in run mode to resume communication. 16399 A fatal CPU fault occurred Critical Fault A fatal CPU fault occurred. Contact technical support.
Appendix B Messages, Codes and Self-test Numbers Error Number Terminal Messages Type Meaning Recommended Action 16417 DHCP/BootP Enable failed Communication Warning The DHCP/BootP Enable server failed to allocate an IP address, subnet mask and gateway address to the PanelView terminal Check DHCP/BootP Enable server on your network. 16418 Invalid IP Address Communication or Subnet Mask Warning The IP address or the subnet mask of the PanelView terminal is not valid.
Messages, Codes and Self-test Numbers Remote I/O Communication Loss Appendix B When communication fails on a remote I/O network: • Object states are maintained and the message No PLC Communication is displayed on the screen. • If Block Transfers are defined for the application, but no BTR or BTW instructions are received, another message appears when the Block Transfer Timeout occurs. These messages continue to display until communication is established.
Appendix B Messages, Codes and Self-test Numbers Test Number Indicates 25 Firmware not compatible with boot code 26 Firmware not compatible with hardware 30 Watchdog test 31 Stuck key test 32 Real time clock test 33 LCD RAM failed 34 Performed CRC extended firmware check TIP You may not see all of these test numbers during a powerup. If a test fails, the terminal displays: ERROR! FEHLER! ERREUR! ERRORE! The following test numbers appear only if a problem occurs.
Appendix C European Union Directive Compliance If the PanelView Operator Terminals are installed within the European Union or EEA regions and have the CE mark, the following regulations apply.
Appendix C European Union Directive Compliance Intended Use of Product According to these Standards, the factor which determines, for EMC purposes, whether a product is deemed to be Industrial rather than Residential, commercial or light industrial, is given in clause 1 of EN50081-2 as follows: Apparatus covered by this standard is not intended for connection to a public mains network supplied from a high- or medium-voltage transformer dedicated for the supply of an installation feeding a manufacturing or
European Union Directive Compliance Appendix C Battery Replacement and Disposal The terminal contains a lithium battery, which is intended to be replaced during the life of the product. At the end of its life, the used battery should be collected separately from any unsorted municipal waste and recycled. The Micro 300 terminal contains a lithium battery, which is permanently connected and should only be removed or replaced by trained professionals.
Appendix C 272 European Union Directive Compliance Publication 2711-UM014G-EN-P - September 2008
Glossary adapter ControlNet device that responds to scanner messages (also called slave device). address 1) A character string that uniquely identifies a memory location. 2) A character string that uniquely identifies the physical location of an input or output circuit. application In the context of PanelBuilder32 software, an application is a logical arrangement of screens that replace the functions of a control panel and consist of push buttons, data entry objects, control lists, and indicators.
Glossary controller A unit, such as a programmable controller or relay panel, that controls machine or process elements. cursor keys Up, down, left, right arrows on the terminal keypad. These keys are used to move a selection cursor or the active object indicator bar. DF1 Allen-Bradley communication protocol based on an ANSI X3.28-1976 specification. download See upload/download. DH-485 link Data Highway 485 link. An Allen-Bradley token-passing carrier-band link for a local area network.
Glossary EPROM Erasable programmable read-only memory. A PROM that can be erased, usually with ultraviolet light, then re-programmed with electrical signals. As with all PROMs, it is nonvolatile random-access memory. EEPROM (flash) Electrically-erasable programmable read-only memory. A type of PROM that can be erased and re-programmed by electrical signals. As with all PROMs, it is nonvolatile random-access memory. Used by the PanelView terminals to store applications.
Glossary keypad Set of 14 keys (numeric 0-9, decimal point, backspace, minus, and enter) to the right of the display on keypad terminals. These keys are used to enter data. LED Light-emitting diode. See status indicator. Memory Card A storage medium that can store a PanelView application and/or a font file. MicroLogix An Allen-Bradley programmable controller.
Glossary PanelView terminal An Allen-Bradley keypad or touch screen terminal providing the operator interface to the logic controller when an application is executing. PC 1) Personal Computer. 2) Programmable Controller. 3) Printed Circuit. PCCC Acronym for Programmable Controller Communication Commands. PGM (Program) PGM setting means the baud rate is set via an explicit message request over the network by another device (typically a configuration tool, such as a PC or DeviceView).
Glossary remote I/O link A serial link for carrying I/O data between a PLC or SLC processor/scanner and remote I/O adapters. repeater Two-port component that receives and transmits all data from one segment to another. restore To load an application from a memory (PC) card. RS-232 An EIA standard that specifies electrical, mechanical, and functional characteristics for serial binary communication circuits in a point-to-point link.
Glossary segment Trunk-cable sections connected through taps with terminators at each end and no repeaters. SLC An Allen-Bradley programmable controller with a name that has the prefix SLC. SMAX Highest ControlNet node address that can communicate during the scheduled portion of the network update interval. status indicator An LED that indicates Comm or Fault status. subnet mask A 32-bit value forming the PanelView terminal’s subnet mask.
Glossary UMAX Highest ControlNet node address that can communicate during the unscheduled portion of the network update interval. upload/download Commonly referred to the reading/writing across a link relatively large blocks of data from one device to another. Whether it is considered an upload or download may depend upon whether it is a read or write and upon which device initiates the transaction. When data is transferred to a programming device, it is considered an upload.
Index A ac power connecting 61 electrical ratings 61 accessories antiglare overlay 53 backlight lamp 56 cables 53-55 file transfer utility 54 function key legend kits 52 memory card retainer 52 memory cards 52 mounting clips 57 mounting studs 57 real time clock 56 wallmount power supply 54 alarms content 131 description 51 antiglare overlay 53 application files running 48 settings 71 ASCII entry controls description 121 entering data 121-124 scratchpad in other languages 125 scratchpads 121-124 audience 15
Index dc power connecting 63-?? electrical ratings 63 declarations of conformity 270 DeviceNet communication active baud rate 83 active node 82 available terminals 18-25 connecting a computer 223 connecting a printer 223 DeviceNet ports 212 input size 84 making connections 213 output size 84 status indicators 84 DF1 communication available terminals 18-25 baud rate 85 Comm status indicator 86 compatible controllers 203 configuration screen 84 connecting to a CompactLogix 205 connecting to a DeviceNet or Et
Index installing the PanelView 1000 clearances 165 cutout dimensions 166 enclosures 162 mounting dimensions 164 panel installation 167 required tools 162 installing the PanelView 1400 clip mounting 173 cutout dimensions 172 enclosures 169 mounting dimensions 170 required tools 169 stud mounting 175 installing the PanelView 300 clearances 142 cutout dimensions 141 enclosures 140 mounting dimensions 140 panel installation 143 required tools 140 installing the PanelView 300 Micro clearances 135 cutout dimensi
Index P PanelView 1000 connecting AC power 61 connecting dc power 63 features 40, 163, 169 installation 161 resetting 66 screen adjustments 94 screen saver 94 specifications 244 PanelView 1400 aligning the touch grid 100 connecting AC power 61 features 44 installation 169 resetting 66 screen adjustments 98 specifications 245 PanelView 300 connecting dc power 63 features 26, 27 resetting 66 specifications 233 PanelView 300 Micro connecting to AIC+ 220 connecting to DNI 220 connecting to MicroLogix 218 conne
Index connecting to a remote I/O scanner 187 last chassis 69, 79 out-of-box application 68 pass-through 69, 78 rack number 69, 78 rack size 69, 78 remote I/O port 185 RS-232 port 185 starting module group 69 supported controllers 186 resetting PanelView 1000 66 PanelView 1400 66 PanelView 300 66 PanelView 300 Micro 66 PanelView 550 66 PanelView 600 66 PanelView 900 66 RS-232 (DH-485) communication available terminals 19-25 CompactLogix connection 200 connecting a computer 223 connecting a printer 223 conne
Index 286 Publication 2711-UM014G-EN-P - September 2008
How Are We Doing? Your comments on our technical publications will help us serve you better in the future. Thank you for taking the time to provide us feedback. You can complete this form and mail (or fax) it back to us or email us at RADocumentComments@ra.rockwell.com. Pub. Title/Type PanelView Standard Operator Terminals Cat. No. PV300 Micro, PV300, PV550, PV600, PV900, PV1000, PV1400 Pub. No. 2711-UM014G-EN-P Pub. Date September 2008 Part No. PN 14527 Please complete the sections below.
Fax: 440-646-3525 Email: RADocumentComments@ra.rockwell.
PLEASE FASTEN HERE (DO NOT STAPLE) Other Comments PLEASE FOLD HERE NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES BUSINESS REPLY MAIL FIRST-CLASS MAIL PERMIT NO.
Rockwell Automation Support Rockwell Automation provides technical information on the Web to assist you in using its products. At http://support.rockwellautomation.com, you can find technical manuals, a knowledge base of FAQs, technical and application notes, sample code and links to software service packs, and a MySupport feature that you can customize to make the best use of these tools.
