PanelView Standard Operator Terminals PV300 Micro, PV300, PV550, PV600, PV900, PV1000, PV1400 User Manual
Important User Information Solid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1 available from your local Rockwell Automation sales office or online at http://www.ab.com/manuals/gi) describes some important differences between solid state equipment and hard-wired electromechanical devices.
Preface Objectives Read this preface to familiarize yourself with the rest of this manual. • • • • • • • • Contents of Manual 1 contents of this manual intended audience conventions used terminology installing PanelView terminals European Union Directive Compliance related publications technical support The following table gives an overview of this manual. Chapter Title Purpose 1 Terminal Overview Describes features of the PanelView terminals.
Preface 2 Chapter Title Purpose 12 Terminal Connections Describes connections for the Remote I/O, DH-485, DH+, RS-232, DF1, ControlNet, DeviceNet and EtherNet/IP versions of the PanelView terminals. Also shows how to connect a computer or printer to terminals with an RS-232 serial port. 13 Troubleshooting and Provides assistance in identifying and correcting common operating problems. Also gives procedures for routine maintenance.
Preface Related Publications 3 Refer to the extensive online help for the PanelBuilder32 Software or the following publications if necessary. Publication Description 2711-GR003 PanelBuilder32 Software Getting Results Manual 2711-QS003 PanelBuilder32 Quick Start Manual 2711-TD006 WinPFT File Transfer Utility 2711-6.3 PROFIBUS DP Communications for PanelView Terminals 2711-6.9 Modbus Communications for PanelView Terminals 1770-4.
Preface 4 What’s New The PanelView 1000 terminals have new AC and DC Power specifications. See Chapter 2 for updated specifications. Ethernet communications is now supported on the following PanelView terminals. • PanelView 550 • PanelView 600 • PanelView 900 (not supported on the monochrome versions) • PanelView 1000 • PanelView 1400 All of these terminals are available with an EtherNet/IP connector and RS-232 port for file transfers and/or printing.
Table of Contents Preface Objectives. . . . . . . . . . . . . . . . . . . . . . Contents of Manual . . . . . . . . . . . . . . . Intended Audience . . . . . . . . . . . . . . . Conventions . . . . . . . . . . . . . . . . . . . . Terminology . . . . . . . . . . . . . . . . . . . . Installing PanelView Terminals . . . . . . European Union Directive Compliance Related Publications . . . . . . . . . . . . . . Technical Support . . . . . . . . . . . . . . . . What’s New . . . . . . . . . . . . . . . . . . . .
Table of Contents 2 Configuring Presets . . . . . . . . . Viewing Terminal Information . Adjusting Screen Parameters . . Setting the Time and Date . . . . Setting up the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17 3-18 3-19 3-28 3-29 Chapter Objectives . . . . . . . . . . . . . . . . .
Table of Contents 3 Chapter 7 Installing the PV300 Terminal Chapter Objectives . . . . . . . . . Hazardous Locations . . . . . . . . Enclosures . . . . . . . . . . . . . . . Required Tools . . . . . . . . . . . . Mounting Dimensions . . . . . . . Cutout Dimensions . . . . . . . . . Clearances . . . . . . . . . . . . . . . Installing the PV300 in a Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents 4 Chapter 11 Installing the PV1400 Terminal Chapter Objectives . . . . . . . . . . Enclosures . . . . . . . . . . . . . . . . Required Tools . . . . . . . . . . . . . Mounting Dimensions . . . . . . . . Clearances . . . . . . . . . . . . . . . . Cutout Dimensions . . . . . . . . . . Installing the PV1400 in a Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents 5 Appendix B Messages, Codes and Self-Test Numbers Types of Terminal Messages . . . . General Terminal Messages . . . . . Terminal Codes. . . . . . . . . . . . . . Remote I/O Communication Loss. Self-test Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1 . B-2 .
Table of Contents 6 Publication 2711-UM014E-EN-P
Chapter 1 Terminal Overview Chapter Objectives This chapter gives an overview of the PanelView Operator Terminals. • intended uses • terminal types and features • applications • configuration mode • terminal messages • printing • accessories and replacement parts Intended Uses You can use the PanelView operator terminals for a wide variety of machine control and monitoring applications.
1-2 Terminal Overview Color and Grayscale Terminals Color terminals support a fixed palette of 32 standard EGA colors. Grayscale terminals support a fixed palette of 4 colors (shades of gray). All color in an application is defined when the application is created. Colors are not selectable at the terminal. PanelView 300 Monochrome Terminals The PanelView 300 terminal is only available with 24V dc input power.
Terminal Overview 1-3 PanelView 550 Monochrome Terminals The Touch Screen version of the PanelView 550 terminal is available only with 24V dc power. The L1 in the catalog number indicates DC power.
1-4 Terminal Overview PanelView 600 Color Terminals Operator Input Communication Port RIO DH-485 RS-232 (DH-485) DH+ DeviceNet ControlNet RS-232 (DF1) Ethernet x Printer Port RS-232 Catalog Number(1) x 2711-B6C1 x 2711-B6C2 x x x 2711-B6C5 x Touch Screen and Keypad x x x x x x x 2711-B6C8 x 2711-B6C9 x 2711-B6C10 x 2711-B6C15 x 2711-B6C16 x 2711-B6C20 x 2711-K6C1 x 2711-K6C2 x x x x x x x x x x 2711-K6C8 x 2711-K6C9 x 2711-K6C10 x 2711-K6C15 x 2711-K6C16
Terminal Overview 1-5 PanelView 900 Monochrome Terminals These terminals are no longer available for purchase.
1-6 Terminal Overview PanelView 900 Color Terminals These terminals are no longer available for purchase. Communication Port Operator Input RIO DH-485 RS-232 DH+ DeviceNet ControlNet RS-232 (DF1) Ethernet (DH-485) x x x x Touch Screen x x x x x x x Keypad x x x x x (1) Add L1 to the end of the catalog number for 24V dc power.
Terminal Overview 1-7 PanelView 1000 Color Terminals Operator Input Communication Port RIO DH-485 RS-232 (DH-485) DH+ DeviceNet ControlNet RS-232 (DF1) Ethernet x x x x Touch Screen x x x x x x x Keypad x x x x x (1) Printer Port RS-232 Catalog Number(1) x 2711-T10C1 x 2711-T10C3 x 2711-T10C8 x 2711-T10C9 x 2711-T10C10 x 2711-T10C15 x 2711-T10C16 x 2711-T10C20 x 2711-K10C1 x 2711-K10C3 x 2711-K10C8 x 2711-K10C9 x 2711-K10C10 x 2711-K10C15 x 2711-K10C16 x 27
1-8 Terminal Overview PanelView 1000 Grayscale Terminals Operator Input Communication Port RIO DH-485 RS-232 (DH-485) DH+ DeviceNet ControlNet RS-232 (DF1) Ethernet x x x x Touch Screen x x x x x x x Keypad x x x x x (1) Add L1 to the end of the catalog number for 24V dc power.
Terminal Overview 1-9 PanelView 1400 Color Terminals PanelView 1400 terminals will not be available after September 2005. Contact your local Rockwell Automation sales office or authorized distributor for suitable substitutes.
1-10 Terminal Overview PanelView 300 Micro Features This section defines features of the PanelView 300 Micro keypad terminal. PanelView 300 Micro Features (Front) 4 2 2 1 3 # Feature Description 1 Function Keys (F1 - F4) Use the function keys to initiate functions on the terminal display.
Terminal Overview PanelView 300 Features 1-11 This section defines features of the PanelView 300 keypad terminal. PanelView 300 Features (Front) 5 4 1 2 3 # Feature Description 1 Function Keys (F1 - F8) Use the function keys to initiate functions on the terminal display. These keys may have custom legends. 2 Cursor Keys Use the up or down cursor keys to move the cursor up or down in a list or to increment/decrement values.
1-12 Terminal Overview PanelView 300 Features (Back) DeviceNet with additional RS-232 Port 3 RS-232 (DH-485 or DF1) without additional RS-232 Port 4 5 10 12 9 or 11 2 DH-485 without RS-232 Port 6 1 8 7 7, 8, 9, 10, 11, 12 # Feature Description 1 Nameplate Label Provides product information. 2 Sealing Gasket Seals the front of the terminal to an enclosure or panel. 3 COMM LED (Green) Indicates when communications is occurring.
Terminal Overview PanelView 550 Features 1-13 This section defines features of the PanelView 550 terminals. PanelView 550 Features (Front) Keypad & Touch Screen Terminal Keypad Terminal Cell 16 Cell 1 3 4 5 6 Cell 113 1 Cell 128 2 Touch Screen Terminal Cell 1 Cell 16 5 6 Cell 113 Cell 128 # Feature Description 1 Function Keys (F1 - F10) On keypad terminals, use the function keys to initiate functions on the terminal display. These keys may have custom legends.
1-14 Terminal Overview PanelView 550 Keypad or Keypad & Touch Screen Terminals (Back) DH-485 without additional RS-232 Port 4 5 3 2 6 7 1 AC connector shown, DC connector looks different 11 10 8 9 DH-485 with additional RS-232 Port 19 10 11 RS-232 (DH-485) without additional RS-232 Port 12 RS-232 (DH-485) with additional RS-232 Port 19 Publication 2711-UM014E-EN-P 12 Backlight lamp behind access cover (Series G and earlier) Remote I/O, DF1, DH+, DeviceNet, ControlNet, Ethernet, with add
Terminal Overview 1-15 # Feature Description 1 Power Connection Terminals Connects to external power source. 2 Nameplate Label Provides product information. 3 Sealing Gasket Seals the front of the terminal to an enclosure or panel. 4 COMM LED (Green) Indicates when communications is occurring. 5 FAULT LED (Red) Indicates firmware or hardware faults. 6 Memory Card Slot Accepts a memory card which stores applications. 7 Access Cover Provides access to the replaceable backlight lamp.
1-16 Terminal Overview PanelView 550 Touch Screen Terminal Features (Back) DH-485 without additional RS-232 Port 5 4 6 3 2 7 1 11 DH-485 with RS-232 Port 10 9 8 Backlight lamp behind access cover (Series A only) 9 11 10 19 RS-232 (DH-485) without additional RS-232 Port Remote I/O, DF1, DH+, DeviceNet, ControlNet, Ethernet, with RS-232 Port 12 RS-232 (DH-485) with additional RS-232 Port 12 Publication 2711-UM014E-EN-P 19 19 13, 14, 15, 16, 17, or 18
Terminal Overview 1-17 # Feature Description 1 Power Connection Terminals Connects to external DC power source. 2 Sealing Gasket Seals the front of the terminal to an enclosure or panel. 3 FAULT LED (Red) Indicates firmware or hardware faults. 4 COMM LED (Green) Indicates when communications is occurring. 5 Nameplate Label Provides product information. 6 Memory Card Slot Accepts a memory card which stores applications. 7 Reset Button Resets the terminal.
1-18 Terminal Overview PanelView 600 Features This section defines features of the PanelView 600 terminals.
Terminal Overview # Feature Description 1 Function Keys (F1 - F10) Use the function keys on keypad terminals to initiate functions on the terminal display. These keys may have custom legends. 1-19 On the keypad & touch screen terminals, you can initiate functions using the function keys and/or touch screen objects. 2 Cursor Keys Use the cursor keys to move the cursor in displayed lists, to select a numeric entry object, or to enter configuration mode.
1-20 Terminal Overview PanelView 600 Keypad or Keypad & Touch Screen Terminal (Back) Remote I/O, DF1, DH+, DeviceNet, ControlNet, or Ethernet with additional RS-232 Port 4 10, 11, 12, 13, 14, or 15 16 DH-485 without additional RS-232 Port 3 2 7 8 1 7, 8, 9, 10 11, 12, 13, 14, 15, 16 6 DH-485 with additional RS-232 Port 16 7 8 RS-232 (DH-485) without additional RS-232 Port 9 Publication 2711-UM014E-EN-P 5 RS-232 (DH-485) with additional RS-232 Port 16 9
Terminal Overview 1-21 # Feature Description 1 Power Connection Terminals Connects to external power source. 2 Nameplate Label Provides product information. 3 Memory Card Slot Accepts a memory card which stores applications. 4 Sealing Gasket Seals the front of the terminal to an enclosure or panel. 5 FAULT LED (Red) Indicates firmware or hardware faults. 6 COMM LED (Green) Indicates when communications is occurring.
1-22 Terminal Overview PanelView 600 Touch-Screen Terminal Features (Back) Remote I/O, DF1, DH+, DeviceNet, ControlNet, or Ethernet with additional RS-232 Port 5 11, 12, 13, 14, 15, or 16 17 4 3 DH-485 without additional RS-232 Port 2 1 8 9 8, 9, 10, 11 12, 13, 14, 15, 16, 17 7 6 DH-485 with additonal RS-232 Port 17 8 9 RS-232 (DH-485) without additional RS-232 Port 10 Publication 2711-UM014E-EN-P RS-232 (DH-485) with additional RS-232 Port 17 10
Terminal Overview 1-23 # Feature Description 1 Power Connection Terminals Connects to external power source. 2 Nameplate Label Provides product information. 3 Fault LED (Red) Indicates firmware or hardware faults. 4 COMM LED (Green) Indicates when communications is occurring. 5 Sealing Gasket Seals the front of the terminal to an enclosure or panel. 6 Reset Button Resets the terminal. 7 Memory Card Slot Accepts a memory card which stores applications.
1-24 Terminal Overview PanelView 900(1)/1000 Features This section defines features of the PanelView 900 and 1000 terminals. PanelView 900/1000 Terminal Features (Front) Keypad Terminal Touch Screen Terminal Cell 1 4 5 6 Cell 24 3 Cell 361 1 Cell 384 2 (1) PanelView 900 terminals are no longer available. Conatct your local sales office or authorized Rockwell Distributor for suitable substitutes.
Terminal Overview 1-25 # Feature Description 1 Function Keys (F1 - F16) Use the function keys on keypad terminals to initiate functions on the terminal display. These keys may have custom legends. 2 Cursor Keys Use the cursor keys to move the cursor in displayed lists, to select a numeric entry object or to enter configuration mode. 3 Numeric Entry Keys 0-9 Enters numeric values. . Enters a decimal point. - Enters a negative value. ← Clears entered digits or cancels the scratchpad.
1-26 Terminal Overview PanelView 900/1000 Terminal Features (Back) Remote I/O, DF1, DH+, DeviceNet, Ethernet, or ControlNet with additional RS-232 Port 4 Back View Touch Screen Terminal 3 11, 12, 13, 14, 15, or 16 17 5 2 DH-485 Version without additional RS-232 Port 6 1 8 9 8, 9, 10 11, 12, 13, 14, 15, 16, 17 7 DH-485 with additional RS-232 Port 4 17 Back View Keypad Terminal 9 8 3 RS-232 (DH-485) without additional RS-232 Port 5 2 6 10 1 RS-232 (DH-485) with additional RS-232 Port 17
Terminal Overview 1-27 # Feature Description 1 Power Connection Terminals Connects to external power source. 2 Nameplate Label Provides product information. 3 Reset Button Resets the terminal. 4 Sealing Gasket Seals the front of the terminal to an enclosure or panel. 5 Memory Card Slot Accepts a memory card which stores applications. 6 FAULT LED (Red) Indicates firmware or hardware faults. 7 COMM LED (Green) Indicates when communications is occurring.
1-28 Terminal Overview PanelView 1400 Features This section defines features of the PanelView 1400 terminals. PanelView 1400 terminals will not be available after September 2005. Contact your local Rockwell Automation sales office or authorized distributor for suitable substitutes.
Terminal Overview 1-29 # Feature Description 1 Function Keys (F1 - F21) Use the function keys on keypad terminals to initiate functions on the terminal display. These keys may have custom legends. 2 Cursor Keys Use the cursor keys to move the cursor in displayed lists, to select a numeric entry object, or to enter configuration mode. 3 Numeric Entry Keys 0-9 Enters numeric values. . Enters a decimal point. - Enters a negative value. ← Clears entered digits or cancels the scratchpad.
1-30 Terminal Overview PanelView 1400 Terminal Features (Back and Sides) Remote I/O, DF1, DH+, DeviceNet, ControlNet, or Ethernet with additional RS-232 Port 19 1 18 17 16 7, 8, 9 10, 11, 12 13, 14, 15, 16 2 10, 11, 12, 13, 14, or 15 DH-485 with additional RS-232 Port 6 5 4 3 Left Side 7 8 16 20 RS-232 (DH-485) with additional RS-232 Port Right Side 9 16 21 Publication 2711-UM014E-EN-P
Terminal Overview # 1 2 3 4 5 6 7 Feature Brightness Control Contrast Control Nameplate Label FAULT LED (Red) COMM LED (Green) Power Connection Terminals DH-485 Communication Port 8 DH-485 Programming Connector 9 RS-232 (DH-485) Communication Port 10 11 12 13 Remote I/O Port DH+ Communication Port DeviceNet Connector ControlNet Connector 14 RS-232 (DF1) Communication Port Ethernet Connector 15 16 17 18 19 20 21 RS-232 Printer/ File Transfer Port Memory Card Eject Button Memory Card Slot Sealin
1-32 Terminal Overview Applications PanelView terminals operate with custom designed applications. The first time you power on the terminal, (no application file loaded), the terminal displays the Configuration Mode menu. Chapter 3 describes the terminal functions you can configure from this menu. TIP Remote I/O terminals provide an out-of-box application for setting Remote I/O communication parameters. If an application is loaded, the terminal displays the application’s start-up screen.
Terminal Overview 1-33 Touch Screen Operation Applications for touch screen terminals are controlled by touching screen objects. Keypad Operation Applications for keypad terminals are controlled by pressing function keys that correspond to screen objects. Data is entered manually using the numeric entry keys. A function key legend kit is available for each terminal (except the 300 Micro) to create custom labels for the function keys. See the accessories at the end of this chapter.
1-34 Terminal Overview Configuration Mode Menu You can configure terminal functions from the Configuration Mode menu including: • • • • • • • • • select a language upload/download applications with a memory card set or display serial communication parameters select preset values obtain terminal and application information adjust screen parameters set time and date set printer parameters (for terminals with an RS-232 printer port) return to run mode Chapter 3 describes how to enter configuration mode an
Terminal Overview Alarm List 1-35 PanelView terminals support an Alarm List queue to store information on triggered alarms. The Alarm List stores a maximum of 100 alarms or as many as the terminal can hold in nonvolatile RAM. The number of alarms stored in the list is configured using the PanelBuilder32 software.
1-36 Terminal Overview Memory Cards and Retainer Catalog No. 300 550 600 900 1000 1400 Description 2711-NM11(1) x x x x x x 256K memory card for storing applications. 2711-NM13 x x x x x x 2M flash memory card for storing applications. 2711-NM14 x x x x x x 4M flash memory card for storing applications. 2711-NM15 x x x x x x 10M flash memory card for storing applications. 2711-NM216(1) x x x x x x 16M flash ATA card for storing applications and font files.
Terminal Overview Catalog No. Description 1761-CBL-AC00 3 meter (9.8 foot) cable connects an RS-232 terminal to an AIC+ (Port1) through a null modem adapter. 1761-CBL-AS03 3 meter (9.8 foot) cable connects a DH-485 terminal to an AIC+ (Port3). 1761-CBL-AS09 9.9 meter (29.5 foot) cable connects a DH-485 terminal to an AIC+ (Port3). 1761-CBL-AM00 45 cm (17.7 inch) cable with 2 mini DIN, right angle connectors. 1761-CBL-HM02 2 meter (6.5 foot) cable with 2 mini DIN, right angle connectors.
1-38 Terminal Overview RS-232 Cables Catalog No. Description 2711-NC13 5 meter (15 foot) connects an RS-232 terminal to the Channel 0 port of an SLC 5/03 controller or the RS-232 port of a computer or printer. 2711-NC14 10 meter (32 foot) cable connects an RS-232 terminal to the Channel 0 port of an SLC 5/03 controller or the RS-232 port of a computer or printer. 2711-NC21 5 meter (15 foot) connects an RS-232 terminal to a MicroLogix controller (except PV300 Micro).
Terminal Overview Replacement Parts 1-39 Backlight Lamps Catalog No. 550 2711-NL1 x 600 900 1000 Description Halogen backlight lamp for all PV550 terminals. Provides backlighting for LCD display. 2711-NL2 x 2711-NL3 Backlight for PV900 color terminal. x Backlight for PV600 color terminal. 2711-NL4 x 2711-NL5 x Backlight for PV1000 color terminal.
1-40 Terminal Overview Panel Mount Clips and Studs Catalog No. 600 900 1000 2711-NP1 2711-NP2 x x 1400 Description x 10 panel mount clips for PV1400 terminal. x 6 panel mount clips for PV600, PV900 or PV1000 terminals. 2711-NP3 x Optional panel mount studs (18) for PV1400 terminals. Remote I/O Connector Catalog No. 550 600 900 1000 1400 Description 22112-046-03 x x x x x Terminal block connector plugs into Remote I/O port of Remote I/O terminals.
Chapter 2 Applying Power and Resetting Terminal Chapter Objectives This chapter provides information on: • • • • Wiring and Safety Guidelines wiring and safety guidelines connecting AC or DC power resetting the terminal power-up sequence Use publication NFPA 70E, Electrical Safety Requirements for Employee Workplaces when wiring the PanelView terminals. In addition to the NFPA general guidelines: • connect the terminal to its own branch circuit.
2-2 Applying Power and Resetting Terminal Hazardous Location Considerations This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D; Class II, Division 2, Groups F and G; Class III; or non-hazardous locations only. The following WARNING statement applies to use in hazardous locations. WARNING EXPLOSION HAZARD • Substitution of components may impair suitability for Class I, Class II, Class III Division 2.
Applying Power and Resetting Terminal Connecting AC Power 2-3 Below are AC electrical ratings for the PanelView terminals. The PV550/PV600 touch screen only terminal is available only with DC power, not AC power.
2-4 Applying Power and Resetting Terminal PanelView 550 Terminal 120/240V ac, 3 Wire, 120/240V ac, 3 Wire, European Harmonized Color Code U.S. Color Code L1 L2N GND L1 L2N GND Black (Line) White (Neutral) Blue (Neutral) Green/Yellow (Protective Earth) Brown (Line) Green (Earth Ground) To Power Source To Power Source PanelView 900/1000 Terminal Power Terminal Block (fixed) 120/240V ac, 3 Wire, European Harmonized Color Code L1 L2N GND/PE 120/240V ac, 3 Wire, U.S.
Applying Power and Resetting Terminal Connecting DC Power 2-5 The L1 versions (Cat. No. 2711-K5A1L1, -T9C1L1) of the PV300, PV300 Micro, PV550, PV600, PV900, and PV1000 terminals connect to a 24V dc power source. The table below shows the electrical ratings for the DC versions of the terminals. Electronic circuitry and an internal fuse protect the terminals from reverse polarity and over-voltage conditions. Terminal Type Supply Voltage (24V dc nominal) Power Consumption PV300 Micro 11 to 30V dc 2.
2-6 Applying Power and Resetting Terminal DC Power Connections Connect the power source to the terminal at the 3-screw terminal block (PV300 Micro removable and PV600 Touch only, all others fixed). WARNING Explosion Hazard • Substitution of components may impair suitability for Class I, Class II, Class III, Division 2. • Do not replace components or disconnect equipment unless power has been switched off or the area is known to be non-hazardous.
Applying Power and Resetting Terminal 2-7 To connect power to the DC versions of the PanelView: 1. Secure the DC power wires to the terminal block screws. PanelView 300 Terminal PanelView 900/1000 Terminal PanelView 550/600 Terminal Power Terminal Block (fixed) Power Terminal Block (fixed) + - Note: In the PanelView 300, the Earth Ground and DC Negative wires are internally connected.
2-8 Applying Power and Resetting Terminal Resetting the Terminal Resetting the terminal re-initializes the PanelView terminal (same as cycling power). To reset the PV300, PV300 Micro, PV550 (keypad, keypad & touch) or the PV600 (keypad, keypad & touch): • Simultaneously press the Left arrow , Right arrow , and Enter ↵ keys. The terminal performs its powerup sequence. The sequence in which keys are pressed (while running an application), determines what appears after the reset.
Applying Power and Resetting Terminal Power-up Sequence 2-9 When resetting or applying power to a PanelView terminal, the terminal runs a series of self-tests. The initial display shows copyright information and the status of each self-test number. See Appendix B for a description of the self-test numbers. COPYRIGHT ALLEN-BRADLEY COMPANY 1999, ALL RIGHTS RESERVED VXX.
2-10 Applying Power and Resetting Terminal For Remote I/O Terminals An out-of-box application screen opens allowing you to set Remote I/O parameters for the terminal. This screen is only available for initial setup. Once an application is downloaded, the Remote I/O setup screen is erased. The table on the next page defines the Remote I/O Parameters.
Applying Power and Resetting Terminal Press this function key on: 550/600 900/1000/1400 F1 To set this RIO Parameter: Description Rack # Rack address of terminal on RIO network. 0 to 76 2-11 Options On PV550/600: Press ↵ to open the scratchpad. Enter the rack address and press ↵ again. On PV900/PV1000/PV1400: Press F1 to set the rack #, then use the up and down arrow keys to select an address.
2-12 Applying Power and Resetting Terminal Publication 2711-UM014E-EN-P
Chapter 3 Configuring the Terminal Chapter Objectives This chapter shows how to use the Configuration Mode menu to configure terminal settings and perform operations including how to: • • • • • • • • • Application Settings access the Configuration Mode menu select a language use a memory card configure communications (DH485, DH+, Remote I/O, ControlNet, DeviceNet, DF1, EtherNet/IP) configure presets view terminal information set the time and date adjust display parameters set up the printer Configura
3-2 Configuring the Terminal Accessing the Configuration Mode Menu The Configuration Mode menu appears on powerup if an application is not loaded or if the menu was last displayed prior to a reset or power down. To access Configuration Mode on keypad terminals: • If an application is running, simultaneously press the Left Right arrow keys on the terminal keypad. TIP and If the Left or Right arrow keys on the PanelView 300 Micro are assigned as function keys, you must use the GoTo Config.
Configuring the Terminal 3-3 Run Mode Runs the loaded application. Reset Video Resets the video to default settings. The reset video function is useful if the screen is set to non-viewable settings. Comm and Fault LED The 2 LEDs on the Configuration Mode menu indicate the operating state of the terminal. The operating states vary for each communication protocol (and the PV300 Micro). See Chapter 13.
3-4 Configuring the Terminal Using a Memory Card Select Memory Card from the Configuration Mode menu to transfer applications between a memory card and the terminal. The PanelView 300 Micro does not support a memory card. Chapter 4 describes the transfer procedure. Valid Card Inserted APPLICATIONS ON CARD \*.
Configuring the Terminal Configuring Communications 3-5 Select Communication Setup from the Configuration Mode menu to display or change the communication settings for your PanelView terminal. The screen that appears depends on the communication protocol of the terminal. DH-485 Communications The DH-485 screen lets you modify or display DH-485 settings for either a DH-485 or RS-232 PanelView terminal.
3-6 Configuring the Terminal Baud Steps through the baud rates with each key press: 1200, 2400, 9600, 19200. The selected baud rate takes effect immediately. Comm LED • solid fill - normal operating state • blinking - no communications established • no fill - hardware failure Fault LED • no fill - normal operating state • blinking - hardware is functioning but an application is not loaded or the current application is corrupted.
Configuring the Terminal 3-7 DH+ Communications The DH+ screen lets you display or modify communication settings for the DH+ version of the PanelView terminals. IMPORTANT Settings downloaded with a DH+ application take priority over terminal settings and take effect immediately after the download. DH+ Node: 2 F1 Baud: 57.6 K F2 Comm LED Fault LED EXIT F16 Node Opens the numeric entry scratchpad. Enter the node address (0 - 77 octal) of the terminal on the DH+ link and press the Enter ↵ key.
3-8 Configuring the Terminal Remote I/O Communications The RIO Configuration screen lets you display communication settings for a Remote I/O terminal. Remote I/O settings are configured with the out-of-box application provided with the terminal or from the PanelBuilder32 software. RIO Configuration Rack Number: Rack Size: Starting Group: Pass-Through Enabled: Last Chassis: 3 Full 0,1 Yes Yes 115.2K Baud: No PLC Communication F3 EXIT F16 Settings are read only, except for baud rate.
Configuring the Terminal 3-9 ControlNet Communications The ControlNet screen lets you display communications settings for a ControlNet terminal. You are only allowed to change the Node Address and Interscan Delay settings. IMPORTANT Settings downloaded with a ControlNet application take priority over terminal settings and take effect immediately after the download.
3-10 Configuring the Terminal Comms Status Displays the current status of the communication card. Connected appears when the PanelView is connected to the network and operating properly. Channel Status Displays a value indicating the current status of channel A and B. The definition of each status condition follows the table. If multiple status conditions apply, the highest priority condition is displayed.
Configuring the Terminal 3-11 Restart Terminal Resets the PanelView terminal. A new node address takes affect after a reset. Exit Returns to the Configuration Mode menu. DeviceNet Communications The DeviceNet screen lets you display or modify communication settings for a DeviceNet terminal. IMPORTANT Settings downloaded with a DeviceNet application take priority over terminal settings and take effect immediately after the download.
3-12 Configuring the Terminal New Baud Step through the baud rates with each key press: 125K (default), 250K, 500K, AutoBaud, PGM. If you select AutoBaud, the terminal determines the baud rate on startup (provided there is sufficient network traffic). If you select PGM, the terminal uses the most recent baud rate stored on the communications card. The selected baud rate takes effect on reset. The maximum cable length is restricted at higher baud rates.
Configuring the Terminal 3-13 Output Size Displays the number of words (0 to 64) received by the PanelView in an I/O message. The default value is 0, which indicates no output data is exchanged with the scanner. This value is set by the downloaded application. Comm LED • solid fill - normal operating state • blinking - no communications established • no fill - hardware failure Exit Returns to the Configuration Mode menu.
3-14 Configuring the Terminal The DF1 port on the PLC-5 controllers allows a parity of Even or None parity with 8 Data Bits. For the SLC controllers, the parity is fixed at None and uses CRC error detection. Baud Rate Steps through the baud rates for the DF1 communications port with each key press: 1200, 2400, 4800, 9600, 19200. The initial default is 9600.The baud rate must match the baud rate of the target device. Error Detection Specifies the type of error checking performed on data.
Configuring the Terminal 3-15 EtherNet/IP Communications The EtherNet/IP screen lets you display or modify some of the EtherNet/IP communication settings for an Ethernet PanelView terminal. Additional parameters (Gateway Address, DNS Server and Domain Name, and Timeout values) are set in the Communications Setup dialog of the PanelBuilder32 software and downloaded with the application.
3-16 Configuring the Terminal IP Address A unique address identifying the PanelView node on the EtherNet/IP network. The IP address is formatted as four sets of decimal numbers with periods between them (10.0.0.1). The range of values for the first set of decimal numbers is 1 - 255, unless all fields are set to 0.0.0.0. The range of values for the last three sets of decimal numbers is 0 255. The default value is 0.0.0.0. A change is not effective until you reset the terminal.
Configuring the Terminal Configuring Presets 3-17 Select Preset Operations from the Configuration Mode menu to set the values of control objects after a reset or power cycle. You can set presets to: • values provided by the PanelView application or • last values entered from terminal prior to a reset or power down.
3-18 Configuring the Terminal Viewing Terminal Information Select Terminal Info from the Configuration Mode menu to display information about your terminal. This information may be needed when calling for technical support. TERMINAL INFO Boot: ############ Firmware: ############ Hardware: ####################################### Filename: ############ ############ Fontfile: ############ ############ Bytes Used Bytes Free EXIT F16 Boot Displays the boot code revision.
Configuring the Terminal Adjusting Screen Parameters 3-19 Select Screen Setup from the Configuration Mode menu to adjust settings of the terminal display. Changes take effect immediately. PanelView 300 Micro Screen Setup The PanelView 300 Micro backlight is always on and intensity is not adjustable. SCREEN SETUP F1 Contrast F2 Mode 6 Normal F3 MORE F4 EXIT SCREEN SAVER F1 Mode F2 Timeout F3 MORE Off 5 min.
3-20 Configuring the Terminal PanelView 300 Screen Setup SCREEN SETUP F1 Contrast F2 Mode F3 Reset Video SCREEN SAVER F1 Mode 6 Normal F7 MORE F2 Timeout F8 EXIT IMPORTANT F7 MORE Off 10 min. F8 EXIT Certain settings may make viewing the screen difficult. Do not exit this screen until viewing adjustments are acceptable. Contrast Increases or decreases the display contrast. The contrast settings range from 0 to 10.
Configuring the Terminal 3-21 PanelView 550 Screen Setup SCREEN SETUP Backlight Off F2 F7 Contrast 10 F3 Backlight Timeout 10 min. IMPORTANT F9 Reset Video F4 Video Mode Reverse EXIT F10 Certain settings may make viewing the screen difficult. Do not exit this screen until viewing adjustments are acceptable. Backlight Turns the backlight On, Off or to Timed mode. When set to Timed, the Backlight Timeout value determines when the backlight is turned off.
3-22 Configuring the Terminal PanelView 600/900/1000 Color - Screen Setup SCREEN SETUP Screen Saver Off Normal Intensity 100 F1 F2 SCREEN SETUP SCREEN SAVER Timed Reset Video F15 SCREEN SAVER Timeout Intensity 10 min. 0 F10 F9 F1 Timeout 10 min. F9 Intensity 0 F10 EXIT F16 Contrast 14 F2 Reset Video F15 color palette adjusts with contrast EXIT F16 PV600 color touch-screen only PV600/900/1000 color IMPORTANT Certain settings may make viewing the screen difficult.
Configuring the Terminal 3-23 PanelView 900 Monochrome - Screen Setup SCREEN SETUP SCREEN SAVER Mode Timed F3 Timeout 10 min. F4 Intensity 80 F5 Normal Intensity 80 F1 Video Mode Normal F2 Reset Video F15 IMPORTANT SCREEN CONDITIONER Mode Disabled F6 Hour Minute ## : 0# F8 F7 EXIT F16 Certain settings may make viewing the screen difficult. Do not exit this screen until viewing adjustments are acceptable.
3-24 Configuring the Terminal Screen Conditioner Mode Enables or disables the screen conditioner. This parameter sets a daily schedule for conditioning the display of a PV900 monochrome terminal to prevent image burn-in. The conditioning process takes approximately 30 minutes and will not start until the terminal is inactive and in screen saver mode. You can interrupt the screen saver or conditioner at any time by pressing a key or the touch screen.
Configuring the Terminal 3-25 PanelView 1000 Grayscale -Screen Setup SCREEN SETUP Screen Saver Video Mode Normal Off F2 F1 SCREEN SAVER Timeout Intensity 10 min. 0 F9 F10 IMPORTANT Reset Video F15 EXIT F16 Certain settings may make viewing the screen difficult. Do not exit this screen until viewing adjustments are acceptable. Video Mode Toggles between normal video (darker text/graphics on a light background) and reverse video (lighter text/graphics on a dark background).
3-26 Configuring the Terminal PanelView 1400 Color Setup SCREEN SAVER Mode Off F1 Timeout 5 min. F2 Intensity 100 SCREEN SETUP DEGAUSS Auto Enabled F4 Hour Minute ## : 0# F3 IMPORTANT F5 F6 Manual Degauss F7 Normal Intensity 100 F8 Reset Video F15 ALIGN TOUCH GRID Touch Screen only EXIT F16 Certain settings may make viewing the screen difficult. Do not exit this screen until viewing adjustments are acceptable. Screen Saver Mode Sets the screen saver to Timed or Off.
Configuring the Terminal 3-27 Manual Degauss Allows you to manually degauss the display. When you press [F7], the display is degaussed immediately. Normal Intensity Adjusts the intensity of the display with each key press: 25, 50, 75, 100. The new setting takes effect immediately. Reset Video Resets the display to normal video (default settings). On keypad terminals, the reset video [F15] key is also active on the Configuration Mode menu.
3-28 Configuring the Terminal Setting the Time and Date Select Date/Time from the Configuration Mode menu to reset the date and/or time. DATE/TIME Year #### Month #### Day #### F1 F2 F3 Hour #### Minute #### Second #### F9 F10 F11 MMM/DD/YYYY MHH:MM:SS PM EXIT F16 Setting the Time Use screen buttons (touch screens) or function keys to set the time.
Configuring the Terminal Setting up the Printer 3-29 Select Printer Setup from the Configuration Mode menu to set parameters for those terminals equipped with an RS-232 printer port. Any printer that supports the IBM enhanced character set can be connected to the RS-232 printer port.
3-30 Configuring the Terminal Top of Form Notifies the PanelView terminal the printer is at the top of a page. Manually adjust the printer to the top of the page before pressing the Top of Form button. The printer also uses the Perforation Skip Value (if defined in the Printer Setup of the PanelBuilder32 software) when the Top of Form button is pressed. On powerup, the terminal assumes the printer is at the top of a page.
Chapter 4 Using a Memory Card Chapter Objectives This chapter describes: • supported memory cards • using the memory card retainer • loading application from a memory card • loading application on a memory card • storing font files on a memory card • removing a memory card Supported Memory Cards Memory cards are available to transfer application files to/from a PanelView terminal with a memory card slot. The PanelView 300 Micro does not support a memory card. PanelView terminals running firmware 3.
4-2 Using a Memory Card Using the Memory Card Retainer A Memory Card Retainer (Catalog No. 2711-NMCC, -NMCD, -NMCE) is shipped with all PanelView terminals, except the PV300 Micro and the PV1400. It is required for: • UL508 installations • vibration/mechanical shock environments • CE certified installations • installations where the application uses a font file on a memory card, and the card must remain in the terminal during operation.
Using a Memory Card 4-3 The Memory Card Retainer protects against: • electrical shock from loose high voltage wires in an electrical enclosure per UL508 ATTENTION When permanently installing a memory card in an electrical enclosure, the memory card retainer must be used to avoid accidental contact of high voltage leads to metal surfaces on the card. Failure to use the retainer could result in physical injury or damage to the terminal.
4-4 Using a Memory Card Loading Application from a Memory Card The procedure below shows how to load an application on a memory card into the PanelView terminal. ATTENTION Explosion Hazard - Do not install or remove memory card unless power has been switched off or the area is known to be non-hazardous. To load an application from a memory card: 1. Insert the memory card in the card slot of the terminal. If the terminal does not have an application loaded, the Configuration Mode menu appears.
Using a Memory Card 4-5 4. Press Memory Card Listing, [F1] on keypad terminals, until the application file you want to load is displayed. 5. Press Restore From Card, [F2] on keypad terminals, to begin the transfer. Because this operation overwrites the current application in the terminal, you are prompted to abort or continue. Proceed with download? F1 - Abort| F2 - Continue The terminal displays the status of the transfer. In progress . . . 6.
4-6 Using a Memory Card Loading Application on a Memory Card The steps below show how to load an application in the terminal onto a memory card. ATTENTION Explosion Hazard - Do not install or remove memory card unless power has been switched off or the area is known to be non-hazardous. To transfer an application to a memory card: 1. Insert the memory card into the card slot of the terminal. 2.
Using a Memory Card 4-7 4. If necessary, press Erase/Format Card, [F4] key on keypad terminals, to format or erase a 2711-NM11, -12, -13, -14, -15 memory card. IMPORTANT Do not perform this operation on a 2711-NM2xx ATA card (where xx is size in megabytes). The card becomes inoperable. Because this operation erases all data on the memory card, you are prompted to abort or continue. Format erases entire card? F1 - Abort F2 - Continue 5.
4-8 Using a Memory Card Storing Font Files on a Memory Card Memory cards also store font files for languages used by PanelView applications. The font file contains the character set for the language. The memory card containing the font file must be inserted in the PanelView terminal while the application is running. The terminal uses the font file to display characters on the application screen.
Chapter 5 Running Applications Chapter Objectives This chapter describes operating procedures common to most applications: screen security alarms push button operation printing control lists time or date numeric entry controls message displays ASCII entry controls numeric data displays screen selectors bar graphs list indicators analog gauges multistate indicators Application Information The application designer is responsible for documenting the operation of an application.
5-2 Running Applications Screen Security Access to some application screens (including the terminal configuration screens) may be restricted. Secured screens require you to enter a password before the screen is displayed. It is the responsibility of the application designer to provide operators with required passwords. Other screens may allow an authorized operator to select and change the passwords of operators at the terminal.
Running Applications Control Lists 5-3 Control lists perform functions similar to push buttons. They can modify either individual bits or values at a controller address. Cursor indicates selected item Active selection is highlighted Vertical bar indicates active control list Active List Item Active item is highlighted. Active Control List Has a vertical indicator bar on the left side of the list. Only one control list or numeric entry cursor point can be active on a screen.
5-4 Running Applications Cursor Indicates the selected item. Move the cursor up or down the control list using the Up and Down arrow keys. Cursor operation is configured by the application designer. If the cursor is at the first or last item in a control list pressing the Up arrow (when at the top) or the Down arrow (when at the bottom) will either: • cause no movement of the cursor, or • move the cursor to the top or bottom of the list.
Running Applications 5-5 Cursor - Piloted Control Lists On a piloted control list, some items are under controller operation only. In addition, some items may be designated as inactive. You cannot select controller items or inactive items. In both cases, the cursor is hollow when you select the item.
5-6 Running Applications Numeric Entry Cursor Point 34962 Cursor points appear as a box. A vertical line on the left side of the box appears when the cursor point is selected. Data is entered in a numeric entry scratchpad. Keypad Enable Button Enter Value 367 A keypad enable button appears like a standard push button. The data displayed in the button is the last value sent to the button’s tag address. When selected, a numeric entry scratchpad opens.
Running Applications 5-7 To enter a value using the keypad enable button: 1. Press the keypad enable button. The scratchpad opens. 2. Enter the value using the terminal keypad and press Enter ↵. To change an entry on a scratchpad: 1. Press the backspace ← key to delete one character at a time. 2. Enter a new value and press Enter ↵. To cancel a scratchpad: 1. Press the Backspace ← key to delete one character at a time.
5-8 Running Applications ASCII Entry Controls ASCII entry controls allow you to send an alphanumeric string (up to 128 characters) to a controller. Like numeric entry controls, the ASCII entry control can appear on a screen as a keypad enable button or a cursor point. When either object is activated, the ASCII scratchpad opens. The look of the scratchpad depends on the terminal.
Running Applications Controls Location Function >> F4 Function Keys Moves the cursor one character to the right in the Display Area. ESC 5 Function Keys Closes the scratchpad without making any changes. CTRL F6 Function Keys Clears the string in the Display Area. 5-9 ASCII Scratchpad - 300 Micro/300 Terminals The thumbwheel scratch pad allows an operator to enter values on terminals without a numeric keypad or touch screen by cycling through the available characters one position at a time.
5-10 Running Applications ASCII Scratchpad - 550/600 Touch Screen Terminals Character Keyboard Cursor Display Area Cursor Control Keys Controls To select characters from the Character Keyboard, press the cursor control keys to move the cursor over a character and then press the SEL key. The character is entered in the Display Area. This area scrolls so you can enter a string that is longer than the Display Area. All characters are sent to the controller even if not visible.
Running Applications 5-11 ASCII Scratchpad - 900/1000/1400 Touch Screen Terminals Display Area Character Keyboard Controls Select characters by touching the Character Keyboard on the screen. The character is entered in the Display Area. This area scrolls so you can enter a string that is longer than the Display Area. All characters are sent to the controller even if not visible. After entering the characters, press ↵ on the scratchpad to send the characters to the controller.
5-12 Running Applications ASCII Scratchpads in Other Languages The ASCII Scratchpad is available with character keyboards in: • • • • French German Italian Spanish If the PanelView terminal is configured for operation in one these languages, the ASCII scratchpad will display the appropriate Character Keyboard. The SHF control toggles between SHF/SHF2. In SHF mode, the Character Keyboard displays the shifted state characters (e.g., a to A, and 3 to #).
Running Applications Screen Selectors 5-13 The 2 types of screen selector controls are Screen List Selectors and Screen buttons. Screen List Selector Screen Controls Monitor Pump Status Vertical Bar indicates active list Valve Status Tank Control Tank Screen Goto Screen Button Previous Screen Return Screen Button Goto and Return screen buttons can have a variety of appearances such as unique inner text, fill pattern, border or shape. Return screen buttons display the previous screen.
5-14 Running Applications Cursor Operation Cursor operation is configured by the application designer.
Running Applications List Indicators 5-15 List indicators highlight an item from a list depending upon the status of either a bit or value at a controller address. List Indicator Mixer Speed Off Low Medium High Current status is highlighted Mixer On Mixer Off An indicator list may have a maximum of 255 entries. The list automatically scrolls to display the status of an item. List indicators do not have a cursor screen selector lists.
5-16 Running Applications Analog Gauges The analog gauge uses a rotating needle to display a process variable such as speed, temperature or pressure. The gauge consists of a circular scale with tick-marks, 1 to 4 needles, and a label with text or variable data. The circular scale is an integral part of the gauge but can be created separately. 80 100 120 60 140 Pressure 40 160 180 20 0 Numeric Data Displays 200 Numeric Data Displays may appear with or without supporting text.
Running Applications Time or Date 5-17 Time and date information can appear as a separate item or in some control/display objects (push buttons, multistate indicators, message displays or data displays). A time and date can appear with or without supporting text. The date can have a variety of formats.
5-18 Running Applications Alarms Applications that support alarms may contain: • Alarm Banner display that pops up when an alarm is triggered • Alarm buttons that enable the operator to act on an alarm (Print Alarm, Acknowledge Alarm, Clear Alarm, Acknowledge All) • Alarm List which stores information on triggered alarms (Print Alarm List or Clear Alarm List button) Alarm configurations are application dependent. Consult your application designer for details on how to handle alarms for your application.
Chapter 6 Installing the PV300 Micro Terminal Chapter Objectives This chapter shows how to install the PanelView 300 Micro terminal and covers: • hazardous locations • enclosures • required tools • mounting dimensions • clearances • cutout dimensions • installing the PV300 micro terminal in a panel Hazardous Location Considerations This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D or non-hazardous locations only.
6-2 Installing the PV300 Micro Terminal Enclosures Mount the PanelView 300 Micro terminal in a panel or enclosure to protect the internal circuitry. The terminal meets NEMA 12/13, 4X (indoor use), IP54 or IP65 ratings only when properly mounted in a panel or enclosure with the equivalent rating. Allow enough space within the enclosure for adequate ventilation. Consider heat produced by other devices in the enclosure.
Installing the PV300 Micro Terminal Cutout Dimensions 6-3 Use the full size template shipped with the PV300 Micro to mark the cutout dimensions. The figure below shows a reduced scale cutout. A full scale template is also available inside the back cover of this document. 4.42 in. (112 mm) 4.0 in. (102 mm) 0.178 in. (4.5 mm) Diameter 3.62 in. (92 mm) 2.12 in. (54 mm) Clearances Allow 51 mm (2.0 inches) of space on all sides of the terminal for adequate ventilation and maintenance.
6-4 Installing the PV300 Micro Terminal Installing Terminal in Panel To install the PV300 Micro in a panel: ATTENTION • Disconnect all electrical power from the panel before making cutout. • Make sure area around the panel cutout is clear. • Take precautions so that metal cuttings do not enter any components already installed in panel. • Failure to follow this warning may result in personal injury or damage to the panel components. 1.
Installing the PV300 Micro Terminal 6-5 5. Alternately tighten the self-locking nuts until the terminal is held firmly against the panel. Tighten the nuts to a torque of 10 inch-pounds. Do not overtighten. ATTENTION Mounting nuts must be tightened to a torque of 10 inch-pounds to provide a proper seal and to prevent potential damage to the terminal.
6-6 Installing the PV300 Micro Terminal Publication 2711-UM014E-EN-P
Chapter 7 Installing the PV300 Terminal Chapter Objectives This chapter shows how to install the PanelView 300 terminal and covers: • hazardous locations • enclosures • required tools • mounting dimensions • clearances • cutout dimensions • installing the PV300 terminal in a panel Hazardous Locations This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D; Class II, Division 2, Groups F and G; Class III Division 2; or non-hazardous locations only.
7-2 Installing the PV300 Terminal See the nameplate on terminal for hazardous locations certifications. ATTENTION In Class I, Class II, Class III Division 2 Hazardous locations, the PanelView terminal must be wired per the National Electric Code as it applies to hazardous locations. Peripheral equipment must also be suitable for the location in which it is installed. The PV300 terminals have an operating temperature code of T4 (maximum operating temperature of 135° C or 275° F).
Installing the PV300 Terminal Mounting Dimensions 7-3 The illustration below shows mounting dimensions for the PV300 keypad terminals. Top View 197 mm (7.76 in) 69mm (2.73 in) 82 mm (3.21 in) 140 mm (5.53 in) Cutout Dimensions Use the full size template shipped with the PV300 terminal to mark the cutout dimensions. Below is a reduce size cutout. 120 am 4.71 in) R 4.5 am via (0.178 in) 109 mm 4.29 in) 140 am 5.53 in) Recommended Panel 178 am 6.
7-4 Installing the PV300 Terminal Clearances When installing the PV300 terminal, allow space for mounting, air flow, maintenance, memory card and legend strip installation. Side, Top and Bottom Clearances Leave 64 mm (2.5 in) for Mounting and Air Flow Terminal Cutout Recommended Panel Leave 64 mm (2.5 in) for Mounting and Air Flow Back Clearance 134.6 mm (5.3 in) 69 mm (2.73 in) Memory Card Retainer Card Publication 2711-UM014E-EN-P 215.9 am (8.5 in) is required with card retainer. Allows 6mm (.
Installing the PV300 Terminal Installing the PV300 in a Panel 7-5 To install the PV300 terminal in a panel: ATTENTION • Disconnect all electrical power from the panel before making the cutout. • Make sure the area around the panel cutout is clear. • Do not allow metal cuttings to enter any components that may already be installed in the panel. • Failure to follow this warning may result in personal injury or damage to the panel components. 1.
7-6 Installing the PV300 Terminal 6. Install the self-locking nuts hand tight. Protective installation label Self-locking nuts (4 used, 6 provided) Mounting Studs (2 left, 2 right) 7. Alternately tighten the self-locking nuts until the terminal is held firmly against the panel. Tighten nuts to a torque of 10 inch-pounds. Do not over-tighten. ATTENTION Mounting nuts must be tightened to a torque of 10 inch-pounds to provide a proper seal and to prevent potential damage to the terminal.
Chapter 8 Installing the PV550 Terminal Chapter Objectives This chapter describes how to mount the PV550 terminal in a panel or enclosure including: • • • • • • • Hazardous Location Considerations hazardous locations enclosures required tools mounting dimensions clearances cutout dimensions installing the PV550 terminal in a panel This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D or non-hazardous locations only.
8-2 Installing the PV550 Terminal ATTENTION In Class I, Division 2 Hazardous locations, the PanelView 550 terminal must be wired per the National Electric Code as it applies to hazardous locations. Peripheral equipment must also be suitable for the location in which it is installed. The following PV550 terminals have an operating temperature code of T2 (maximum operating temperature of 300° C or 572° F).
Installing the PV550 Terminal Required Tools 8-3 Other than the tools required to make the PV550 panel cutout, the tools required for installation are: • 7 mm (M4) deep well socket wrench or nut driver • small slotted screwdriver • torque wrench (in / lbs) Mounting Dimensions The illustration below shows mounting dimensions for the PV550 terminals. PV550 Keypad, Keypad & Touch Screen Terminals Top View 167 mm (6.57 in) 106 mm (4.17 in) 86 mm (3.39 in) 266 mm (10.
8-4 Installing the PV550 Terminal Clearances When installing the PV550 terminal, allow space for mounting, air flow, maintenance, memory card and legend strip installation. PV550 Keypad, Keypad & Touch Screen Terminals PV550 Touch Screen Terminals Leave 25 mm (1.0 in) for Mounting and Air Flow Terminal Cutout Use full size template shipped with terminal Leave 25 mm (1.0 in) for Mounting and Air Flow Leave 38 mm (1.5 in) for Mounting, Air Flow and Wiring Connections Back Clearance 109 mm (4.
Installing the PV550 Terminal Cutout Dimensions 8-5 Use the full size template shipped with the PV550 terminal to mark the cutout dimensions. Below is a reduce size cutout. PV550 Keypad, Keypad & Touch Screen Terminals 243 mm (9.55 in) 191 mm (7.51 in) 25.9 mm (1.02 in) 3.3 mm (0.13 in) 150 mm (5.91 in) 106 mm (4.19 in) 85 mm (3.33 in) 4.8 mm dia (0.188 in) 3.3 mm (0.13 in) Front Recommended Panel Cutout Dimensions 144 mm (5.66 in) PV550 Touch Screen Terminals 165 mm (6.49 in) 4.8 mm dia. (0.
8-6 Installing the PV550 Terminal Installing the PV550 in a Panel To install the PV550 terminal in a panel: ATTENTION • Disconnect all electrical power from the panel before making the cutout. • Make sure the area around the panel cutout is clear. • Do not allow metal cuttings to enter any components that may already be installed in the panel. • Failure to follow this warning may result in personal injury or damage to the panel components. 1.
Installing the PV550 Terminal 8-7 PV550 Keypad, Keypad & Touch Screen Terminals Mounting Studs (3 Top, 3 Bottom) Protective installation label Self-locking nuts (6 used, 8 provided) PV550 Touch Screen Terminal Protective installation label Mounting Studs (2 Left, 2 Right) Self-locking nuts (4 used, 8 provided) 8. Alternately tighten the self-locking nuts until the terminal is held firmly against the panel. Tighten nuts to a torque of 10 inch-pounds. Do not over-tighten.
8-8 Installing the PV550 Terminal Publication 2711-UM014E-EN-P
Chapter 9 Installing the PV600 Terminal Chapter Objectives This chapter describes how to mount the PV600 terminal in a panel or enclosure including: • • • • • • • Hazardous Location Considerations hazardous locations enclosures required tools mounting dimensions cutout dimensions clearances installing the PV600 terminal in a panel This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D or non-hazardous locations only.
9-2 Installing the PV600 Terminal See the nameplate label on terminal for certifications on hazardous locations. ATTENTION In Class 1, Division 2 Hazardous locations, the PanelView terminal must be wired per the National Electric Code as it applies to hazardous locations. Peripheral equipment must also be suitable for the location in which it is installed. The PV600 terminals have an operating temperature code of T4 (maximum operating temperature of 135° C or 275° F).
Installing the PV600 Terminal Mounting Dimensions 9-3 The illustration below shows mounting dimensions for the PV600 terminals. PV600 Keypad, Keypad & Touch Screen Terminals 6.9 mm (0.27 in) 192 mm (7.55 in) Top View 116 mm (4.57 in) 91 mm (3.60 in) 290 mm (11.40 in) PV600 Touch Screen Terminals Top View 152 mm (6.00 in) 79 mm (3.12 in) 96 mm (3.80 in) 185 mm (7.
9-4 Installing the PV600 Terminal Cutout Dimensions Use the full size template shipped with the PV600 terminal to mark the cutout dimensions. Below is a reduce size cutout. PV600 Keypad, Keypad & Touch Screen Terminals 167 mm (6.57 in) Recommended Panel Cut-out Dimensions 264 mm (10.39 PV600 Touch Screen Terminals 4.8 mm dia. (0.188 in) 98 mm (3.86 in) Publication 2711-UM014E-EN-P 165 mm (6.49 in) 158 mm (6.20 in) Recommended Panel Cut-out Dimensions R 1.8 mm (0.07 in) 125 mm (4.
Installing the PV600 Terminal Clearances 9-5 When installing the PV600 terminal, allow adequate space for mounting, air flow, maintenance, memory card and legend strip installation. PV600 Keypad and Keypad & Touch Screen Terminals Side, Top and Bottom Clearances 51 mm (2.0 in) for Mounting and Air Flow 25 mm (1.0 in) for Mounting and Air Flow 6.9 mm (0.27 in) Terminal Cutout - Front View Use full size template shipped with terminal Back Clearance 91 mm Memory Card Retainer Card 51 mm (2.
9-6 Installing the PV600 Terminal Installing the PV600 in a Panel To install the PV600 terminal in a panel: ATTENTION • Disconnect all electrical power from the panel before making the cutout. • Make sure the area around the panel cutout is clear. • Do not allow metal cuttings to enter any components that may already be installed in the panel. • Failure to follow this warning may result in personal injury or damage to the panel components. 1.
Installing the PV600 Terminal 9-7 5. Install the 4 mounting clips (2 on top, 2 on bottom). The ends of the clips slide into the slots on the terminal. Tighten the clip mounting screws by hand until the gasket seal contacts the mounting surface uniformly.
9-8 Installing the PV600 Terminal Publication 2711-UM014E-EN-P
Chapter 10 Installing the PV900/1000 Terminals Chapter Objectives This chapter describes how to mount the PV900 and PV1000 terminals in a panel or enclosure including: • • • • • • Hazardous Location Considerations hazardous locations and enclosures required tools mounting dimensions clearances cutout dimensions installing the PV900/PV1000 terminal in a panel This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D; Class II, Division 2, Groups F and G; Class III Division 2; or non-
10-2 Installing the PV900/1000 Terminals See the nameplate on terminal for hazardous locations certifications. ATTENTION In Class I, Class II, Class III Division 2 Hazardous locations, the PanelView 550 terminal must be wired per the National Electric Code as it applies to hazardous locations. Peripheral equipment must also be suitable for the location in which it is installed. The PV900/PV1000 terminals have an operating temperature code of T4 (maximum operating temperature of 135° C or 275° F).
Installing the PV900/1000 Terminals Mounting Dimensions 10-3 PV900 Terminals The illustrations below show mounting dimensions for the PV900 monochrome and color terminals. PV900 Touch Terminal Mounting Dimensions 6.9 mm (0.27 in) 249 mm (9.80 in) Top View 112 mm (4.40 in) 90 mm (3.54 in) 336 mm (13.24 in) PV900 Keypad Terminal Mounting Dimensions 6.9 mm (0.27 in) 249 mm (9.80 in) 90 mm (3.54 in) Top View 112 mm (4.40 in) 406 mm (15.
10-4 Installing the PV900/1000 Terminals PV1000 Terminals The illustrations below show the mounting dimensions for the PV1000 grayscale and color terminals. PV1000 Touch Terminal Mounting Dimensions 6.9 mm (0.27 in) 282 mm (11.11 in) Top View 112 mm (4.40 in) 90 mm (3.54 in) 370 mm (14.58 in) PV1000 Keypad Terminal Mounting Dimensions 6.9 mm (0.27 in) 282 mm (11.11 in) 423 mm (16.64 in) Publication 2711-UM014E-EN-P 90 mm (3.54 in) Top View 112 mm (4.
Installing the PV900/1000 Terminals Clearances 10-5 Allow adequate space for mounting, air flow, maintenance, memory card and legend strip installation. IMPORTANT If using a memory card and/or memory card retainer, allow a back clearance to load the card. Side, Top and Bottom Clearances Leave 51 mm (2.0 in) for Mounting and Air Flow Terminal Cutout - Front View Use full size template shipped with terminal Leave 51 mm (2.0 in) for Mounting and Air Flow Leave 51 mm (2.
10-6 Installing the PV900/1000 Terminals Cutout Dimensions Use the full size template shipped with the PV900 and PV1000 terminals to mark the cutout dimensions. The following illustrations show reduced cutouts for these terminals with dimensions. PV900 Panel Cutout Dimensions PV900 Touch Screen Terminals PV900 Keypad Terminals 224 mm (8.8 in) Recommended Panel Cut-out Dimensions 224 mm (8.8 in) 375 mm (14.75 in) Recommended Panel Cut-out Dimensions 305 mm (12.
Installing the PV900/1000 Terminals Installing the PV900/PV1000 in a Panel 10-7 To install the PV900/PV1000 terminal in a panel: ATTENTION • Disconnect all electrical power from the panel before making the cutout. • Make sure the area around the panel cutout is clear. • Do not allow metal cuttings to enter any components that may already be installed in the panel. • Failure to follow this warning may result in personal injury or damage to the panel components. 1.
10-8 Installing the PV900/1000 Terminals 5. Install the 6 mounting clips (2 on top, 2 on bottom, 1 on each side). The ends of the clips slide into the slots on the terminal. Tighten the clip mounting screws by hand until the gasket seal contacts the mounting surface uniformly. Protective installation labels Install 6 mounting clips: Top - left and right slots Bottom - left and right slots Sides - left and right 6. Alternately tighten the mounting clip screws to a torque of 10 inch-pounds.
Chapter 11 Installing the PV1400 Terminal Chapter Objectives This chapter describes how to mount the PV1400 terminal in a panel or enclosure including: • enclosures • recommended tools • mounting dimensions • clearances • cutout dimensions • installing the PV1400 terminal in a panel Enclosures The PV1400 terminal must be mounted in an environment that provides IEC-1131-2 Pollution degree 2 protection. Mount the PV1400 terminal in a panel or enclosure to protect the internal circuitry.
11-2 Installing the PV1400 Terminal Mounting Dimensions The illustrations below show mounting dimensions for the PV1400 terminals. PV1400 Touch Terminal Mounting Dimensions 3.3 mm (0.13 in) 355 mm (13.97 in) Top View 394 mm (15.53 in) 370 mm (14.58 in) 441 mm (17.37 in) PV1400 Keypad Terminal Mounting Dimensions 3.3 mm (0.13 in) 355 mm (13.97 in) 483 mm (19.0 in) Publication 2711-UM014E-EN-P 370 mm (14.58 in) Top View 394 mm (15.
Installing the PV1400 Terminal Clearances 11-3 Allow adequate space for mounting, air flow, maintenance, adjusting brightness/contrast, memory card and legend strip installation. IMPORTANT If using a memory card, allow a back clearance to load the card. Side, Top and Bottom Clearances Leave 51 mm (2.0 in) for Mounting and Air Flow Terminal Cutout - Front View Leave 51 mm (2.0 in) for Mounting Leave 51 mm (2.0 in) 3.3 mm (0.13 in) Back Clearance 370 mm (14.58 in) Approximately 400 mm (15.
11-4 Installing the PV1400 Terminal Cutout Dimensions Use the full size template provided with the terminal to mark cutout dimensions. The illustration below shows reduced size cutouts with dimensions. PV1400 Keypad Terminals 419 mm (16.50 in) 110 mm (4.35 in) 221 mm (8.70 in) 170 mm (6.70 in) 7/32 in (5.56 mm) Typical 18 Holes 140 mm (5.50 in) 38mm 1.50 in 305 mm (12.0 in) Ignore stud holes if mounting terminal using panel clips. 233 mm (9.16 in) PV1400 Touch Screen Terminals 391 mm 127 mm (5.
Installing the PV1400 Terminal Installing the PV1400 in a Panel 11-5 This section gives procedures for mounting a PV1400 using: • mounting clips (10 shipped with terminal, 10 required) • mounting studs (ordered separately, Catalog No. 2711-NP3) ATTENTION • Disconnect all electrical power from the panel before making the cutout. • Make sure the area around the panel cutout is clear. • Do not allow metal cuttings to enter any components that may already be installed in the panel.
11-6 Installing the PV1400 Terminal 5. Install the 10 mounting clips (3 on top, 3 on bottom, 2 on each side). The ends of the clips slide into slots on the terminal.Tighten the clip mounting screws hand tight. Install 10 Mounting Clips Keypad Version = Recommended Placement of Mounting Clips Touch Screen Version 6. Alternately tighten the mounting clip screws until the terminal is held firmly against the panel. Tighten mounting screws to a torque of 10 inch-pounds. Do not over-tighten.
Installing the PV1400 Terminal 11-7 To install the PV1400 terminal in a panel using mounting studs: 1. Cut an opening in the panel using the panel cutout shipped with the terminal. Carefully drill 5.56 mm (7/32 inch) holes for studs as indicated. 2. Install the mounting studs (Catalog No. 2711-NP3) using a 7/32-inch socket on the end of the stud. Turn stud clockwise and tighten to approximately 10-inch pounds (1.1 N•m).
11-8 Installing the PV1400 Terminal 5. Install the self-locking nuts hand tight. Tighten mounting nuts to a torque of 10 inch-pounds (1.1 N•m) to provide a proper seal and prevent potential damage to the terminal. Allen-Bradley assumes no responsibility for water or chemical damage to the terminal or other equipment within the enclosure because of improper installation. A properly installed terminal has a small gap between the bexel and enclosure. ATTENTION 6.
Chapter 12 Terminal Connections Chapter Objectives This chapter describes network and device connections for PanelView terminals.
12-2 Terminal Connections Cable Charts Refer to the following charts for a summary of PanelView terminal connections to controllers and network interface modules.
Terminal Connections 12-3 Cables: PanelView to Processor Protocol PanelView Standard Comm Port PLC-5, PLC-5C, PLC-5E CH0 (25-pin RS-232) (DF1) ControlLogix CH0 (9-pin RS-232) (DF1) MicroLogix 1000, 1200, 1500LSP CH0 (8-pin Mini DIN) (DF1 or DH-485) DF1 xxx16 xxx17 xxx18 RS-232 (DF1) Comm Port (8-pin Mini Din) PanelView 300 Micro 2711-xxx18 1761-CBL-AP00 (1.5ft/0.5m) 1761-CBL-PM02 (6.5ft/2m) 2711-CBL-PM05 (16ft/5m) 2711-CBL-PM10 (32ft/10m) (9-to-25 pin adapter required) 1761-CBL-AP00 (1.5ft/0.
12-4 Terminal Connections Cables: PanelView to Processor Protocol PanelView Standard Comm Port MicroLogix 1500LRP CH1 (9-pin RS-232) (DF1 or DH-485) CompactLogix CH0 (9-pin RS-232) (DF1 or DH-485) FlexLogix CH0 (9-pin RS-232) (DF1) DF1 xxx16 xxx17 xxx18 RS-232 (DF1) Comm Port (8-pin Mini Din) PanelView 300 Micro 2711-xxx18 1761-CBL-AP00 (1.5ft/0.5m) 1761-CBL-PM02 (6.5ft/2m) 2711-CBL-PM05 (16ft/5m) 2711-CBL-PM10 (32ft/10m) 1761-CBL-AP00 (1.5ft/0.5m) 1761-CBL-PM02 (6.
Terminal Connections 12-5 Runtime Communication Cables - to Network Interface Module Cables: PanelView to Interface Module Protocol PanelView Standard Comm Port 1747-AIC 1761-NET-AIC DF1 xxx16 xxx17 xxx18 RS-232 (DF1) Comm Port (8-pin Mini Din) PanelView 300 Micro 2711-xxx18 N/A 1761-CBL-AP00 (1.5ft/0.5m) 1761-CBL-PM02 (6.5ft/2m) 2711-CBL-PM05 (16ft/5m) 2711-CBL-PM10 (32ft/10m) 1761-CBL-AM00 (1.5ft/0.5m) 1761-CBL-HM02 (6.
12-6 Terminal Connections Application File Upload/Download (Direct) Cables PanelView Standard Type Cable to Personal Computer PanelView 300 Micro 2711-M3A18L1, -M3A19L1 1761-CBL-PM02 (6.
Terminal Connections Remote I/O Terminal Connections 12-7 This section describes connections for the Remote I/O PanelView terminals including: • Remote I/O port • supported controllers • making Remote I/O connections • Remote I/O Pass-Through Remote I/O Terminal Ports The Remote I/O versions of the PanelView terminal (catalog numbers ending in 1) have a Remote I/O port and an RS-232 port. Use the Remote I/O port to: • communicate with the Remote I/O scanner port on a PLC controller.
12-8 Terminal Connections Supported Controllers The Remote I/O terminal connects to any Allen-Bradley 1771 Remote I/O link. Applicable host controllers include almost all Allen-Bradley PLCs, computers, VME controllers, and DEC Q-Bus controllers with a Remote I/O scanner module. New PLC product releases that support 1771 Remote I/O will also work with PanelView.
Terminal Connections 12-9 Making Remote I/O Connections To connect a PanelView terminal to a Remote I/O scanner, use cable Catalog No. 1770-CD (equivalent to Belden 9463). The maximum cable length (link distance) is determined by the baud rate. • 2,800 meters (10,000 feet) for 57.6K baud • 1,400 meters (5,000 feet) for 115.2K baud • 700 meters (2,500 feet) for 230.4K See Programmable Controller Wiring and Grounding Guidelines (Publication 1770-4.1).
12-10 Terminal Connections Remote I/O Pass-Through using DH+ Remote I/O terminals allow the transfer of applications from a computer on the Allen-Bradley DH+ link to a PLC-5 or SLC-5/04 controller. The controller passes data to the PanelView terminal over the Remote I/O network. PLC-5 DH+ Computer Remote I/O Pass-Through Remote I/O Network PanelView To transfer an application using Remote I/O Pass-Through: 1. A Data Highway Plus Interface Module must be installed in the computer.
Terminal Connections DH+ Terminal Connections 12-11 This section describes connections for the DH+ PanelView terminals including: • DH+ ports • typical DH+ system configuration • making DH+ connections DH+ Terminal Ports The DH+ versions of the PanelView terminals (catalog numbers ending in 8) have a DH+ port and an RS-232 port. Use the DH+ port to: • communicate with a PLC-5 controller on the Allen-Bradley DH+ link via the processor’s DH+ port.
12-12 Terminal Connections Typical DH+ System Configuration For more information on the Allen-Bradley DH+ link, refer to: • 1785-5.7 Enhanced PLC-5 Programmable Controllers Installation Instructions • 1770-6.2.2 Data Highway/Data Highway Plus/Data Highway II/Data Highway 485 Cable Installation Manual.
Terminal Connections 12-13 Making DH+ Connections Use the Belden 9463 twin axial cable (1770-CD) to connect a DH+ PanelView terminal to the DH+ link. You can connect a DH+ link in 2 ways: • trunk line/drop line - from the drop line to the connector screw terminals on the DH+ connectors of the processor • daisy chain - to the connector screw terminals on the DH+ connectors on the processor Follow these guidelines when installing DH+ communication links.
12-14 Terminal Connections DH-485 Terminal Connections This section describes connections for the DH-485 PanelView terminals. • • • • • DH-485 terminal ports Connecting to a single SLC controller (Point-to-Point) Connecting to a DH-485 network Connecting a computer Connecting a Hand-held terminal TIP For PanelView 300 Micro terminals, refer to page 12-41. DH-485 Terminal Ports (RJ45) DH-485 PanelView terminals with catalog numbers ending in 2 have two DH-485 ports.
Terminal Connections 12-15 The DH-485 communications port and programming connector may appear in different locations on specific terminals. Identify the ports by their size and shape or by the port labels. DH-485 SLC Programming Port RS-232 Printer Port DH-485 Communications Port RS-232 Printer Port DH-485 Communications Port DH-485 SLC Programming Port Connecting to a Single SLC Controller (Point-to-Point) To connect a DH-485 terminal to a single SLC controller use one of these cables: • 0.
12-16 Terminal Connections The DH-485 connectors are not electrically isolated. If electrical isolation is required, use Link Couplers (Catalog No. 1747-AIC) as shown on next page. Electrical isolation using Link Couplers (Catalog No. 1747-AIC) is required where the distance between the PanelView terminal and the SLC is greater than 6.1 meters (20 feet).
Terminal Connections IMPORTANT 12-17 The DH-485 network cable requires proper shielding, grounding and termination. Refer to Data Highway / Data Highway Plus / Data Highway-485 Cable Installation Manual (Publication No. 1770-6.2.2). The illustration below shows how to connect a DH-485 terminal to a MicroLogix or SLC controller using the AIC+ Link Coupler (Catalog No. 1761-NET-AIC). AIC+ 1761-NET-AIC PanelView 1000 MicroLogix 1000, 1200, 1500LSP Cable Cat. No. 1761-CBL-AS03 Cat. No.
12-18 Terminal Connections Connecting a Computer On DH-485 terminals, PanelView applications are transferred: • through the DH-485 programming connector to the terminal. • through any node on a DH-485 network. To connect a computer to the PanelView terminal, you need: • a cable (same cables used to transfer applications from APS software to SLC) – 0.3 meter (1 foot) cable, Catalog No. 1747-C11 – 1.83 meter (6 foot) cable, Catalog No. 1747-C10 – 6.1 meter (20 foot) cable, Catalog No.
Terminal Connections 12-19 Connecting a Computer to DH-485 Connector Using a Power Supply PanelBuilder32 PanelView 1000 Wallmount Power Supply Cat. No. 1747-NP1 To DH-485 Programming Connector 25-pin to 9-pin Adapter (if required) Personal Computer Interface Converter (Cat. No. 1747-PIC) To DH-485 Communications Port Cable Cat. No. 1747-C10 Cat. No. 1747-C11 Cat. No.
12-20 Terminal Connections Connecting a Hand-Held Terminal To connect a Hand-Held Terminal (HHT) to the PanelView terminal, use cable Catalog No. 1747-C10. One end of the cable connects to the HHT connector and the other end connects to the DH-485 programming connector on the terminal. All power is supplied to the HHT through the cable. IMPORTANT The PanelView terminal must be connected to an SLC, DH-485 network or power supply. This connection provides power for the HHT. Hand-Held Terminal Catalog No.
Terminal Connections RS-232 (DH-485) Terminal Connections 12-21 This section describes connections for the RS-232 (DH-485) PanelView terminals including: • RS-232 ports • connecting to a SLC, CompactLogix, or MicroLogix Controller (point-to-point) • connecting to a MicroLogix Controller through the AIC+ module • connecting a computer • connecting to a DH-485 link Refer to page 12-41 for PanelView 300 Micro RS-232 connections RS-232 Terminal Ports RS-232 (DH-485) PanelView terminals with catalog numbers
12-22 Terminal Connections Connecting to an SLC, CompactLogix, MicroLogix (Point-to-Point) This section shows how to connect a CompactLogix, MicroLogix 1500LRP, or SLC controller (SLC-5/03, 5/04, or 5/05) to the RS-232 PanelView terminal for point-to-point (DH-485) communications. On terminals with two ports, use the RS-232 Communications Port. For the SLC, CompactLogix or MicroLogix 1500LRP controller, use one of these cables: • 5 meter (16.4 foot) Catalog No. 2711-NC13 • 10 meter (32.7 foot) Catalog No.
Terminal Connections 12-23 Connecting to a MicroLogix Controller through an AIC+ This section shows how to connect the RS-232 (DH-485) version of the PanelView terminal to a MicroLogix controller through an AIC+ Link Coupler. AIC+ Cat. No. 1761-NET-AIC MicroLogix 1000, 1200, 1500LSP Belden Cable 9842 Catalog No. 1761-CBL-HM02 1761-CBL-AM00 Catalog No. 1747-CP3 RS-232 Communication Cables Cable, Cat. No. 2711-NC13 Cable, Cat. No. 2711-NC14 Cable, Cat. No.
12-24 Terminal Connections Connecting a DH+ to DH-485 Pass-Through Link This section shows connections for transferring applications between a computer on the Allen-Bradley DH+ link and an RS-232 (DH-485) PanelView terminal, through an SLC 5/04 controller. The RS-232 (DH-485) Communications port on the terminal connects to the CH0 port of the controller using one of the cables listed below.
Terminal Connections RS-232 (DF1) Terminal Connections 12-25 This section describes connections for the RS-232 (DF1) versions of the PanelView terminal including: • • • • • compatible controllers RS-232 terminal ports connecting to a controller (point-to-point) using a modem connecting to a DeviceNet or EtherNet/IP network TIP For PanelView 300 Micro terminals, refer to page 12-41. Compatible Controllers The RS-232 (DF1) terminals support full duplex communications with the following controllers.
12-26 Terminal Connections RS-232 (DF1) Terminal Ports The RS-232 (DF1) PanelView terminals, with catalog numbers ending in 17, have a single RS-232 commuications port supporting DF1 (Full Duplex) communications port. PanelView terminals with catalog numbers ending in 16 also have an RS-232 printer/file transfer port. • Use the DF1 port to communicate with a logic controller using DF1 full duplex communications.
Terminal Connections 12-27 Connecting to a MicroLogix 1000 The following shows a point-to-point connection between the RS-232 (DF1) port of the PanelView terminal and a MicroLogix 1000. PanelView Cables: 2711-NC21 2711-NC22 PanelView MicroLogix 1000, 1200, 1500LSP AIC+ 1761-NET-AIC MicroLogix 1000 DF1 Port 1761-CBL-HM02 DF1 Port DF1 Port Use a direct connection when both the PanelView and MicroLogix use the same power supply. Otherwise, use the AIC for electrical isolation as shown to the right.
12-28 Terminal Connections Connecting to a CompactLogix or FlexLogix The following shows a point-to-point connection between the DF1 port of the PanelView and a CompactLogix or FlexLogix controller. CompactLogix PanelView DF1 Port DF1 Port FlexLogix 2711-NC13, -NC14 Cable DF1 Port Using a Modem Wire or radio modem communications is possible between a DF1 terminal and controller. Each modem must support full duplex communications.
Terminal Connections 12-29 Connecting to a DeviceNet or EtherNet/IP Network The following illustration shows a DF1 PanelView terminal connected to a single controller (MicroLogix, SLC or PLC) on: • a DeviceNet network via 1761-NET-DNI modules or • an EtherNet/IP network via 1761-NET-ENI modules MicroLogix 1000 1761-NET-DNI Module for DeviceNet 1761-NET-ENI Module for EtherNet/IP DF1 PanelView DF1 1761-CBL-HM02 or DeviceNet or EtherNet/IP SLC 5/03, 5/04, 5/05 1761-CBL-PM02 DF1 port 2711-NC22 or -NC22
12-30 Terminal Connections ControlNet Connections This section describes connections for the ControlNet PanelView terminals including: • • • • • ControlNet Protocol Compatible ControlNet Controllers ControlNet ports on the PanelView terminal Typical ControlNet network Making ControlNet connections Related Information For more information on ControlNet products, refer to the following publications. • ControlNet System Overview (Publication 1786-2.
Terminal Connections 12-31 Compatible ControlNet Controllers The ControlNet PanelView terminal communicates with a PLC-5C (using PCCC commands) or a ControlLogix processor (using CIP protocol) using unscheduled and scheduled messaging.
12-32 Terminal Connections Typical ControlNet Network Below is a typical ControlNet network with a PanelView terminal installed on a network drop.
Terminal Connections 12-33 Making ControlNet Connections Use the pinout information below to connect the PanelView to a ControlNet network. IMPORTANT Follow the ControlNet network layout and design as specified in the ControlNet Cable System Planning and Installation Manual (Publication 1786-6.2).
12-34 Terminal Connections NAP and Redundant Cables ControlNet cables, taps, connectors. Refer to the ControlNet Cable System Planning and Installation manual (Publication 1786-6.2.1) for descriptions of these components. For information on purchasing these items, refer to the Allen-Bradley ControlNet Cable System Component List (Publication AG-2.2).
Terminal Connections DeviceNet Terminal Connections 12-35 This section describes connections for the DeviceNet PanelView terminals including: • DeviceNet connectors • connections • typical DeviceNet network DeviceNet Terminal Ports The DeviceNet versions of the PanelView terminals (catalog numbers ending in 10) have a DeviceNet port and an RS-232 serial port. • Use the DeviceNet port to connect to devices on a DeviceNet network or transfer applications over a DeviceNet network.
12-36 Terminal Connections Making DeviceNet Connections Use one of the cables below to connect the DeviceNet version of the PanelView terminal to a DeviceNet network. Cable Publication No. DeviceNet Cable, 50 meters (164 feet) 1485C-P1A50 DeviceNet Cable, 100 meters (328 feet) 1485C-P1A150 DeviceNet Cable, 150 meters (492 feet) 1485C-P1A300 IMPORTANT DeviceNet Terminal Block 1 5 Publication 2711-UM014E-EN-P Refer to DeviceNet Cable System Planning and Installation manual (Publication 1485-6.
Terminal Connections 12-37 Typical DeviceNet Network Below is a typical DeviceNet network with PanelView terminals installed on 2 of the network drops. A DeviceNet network requires a 24V dc power supply. DeviceNet power consumption is 24mA - 90mA @24V dc. The PanelView terminal does not receive its power from the network. PLC-5 SLC 5/04 or DeviceNet Scanner Module (Cat. No. 1747-SDN) DeviceNet Scanner Module (Cat. No.
12-38 Terminal Connections EtherNet/IP Connections The EtherNet/IP PanelView terminal can communicate on an EtherNet TCP/IP network with the following devices: • PLC-5E or PLC-5 with 1761-NET-ENI or 1785-ENET module • SLC-5/05 or SLC with 1761-NET-ENI module • ControlLogix controller with 1756-ENET/B or 1761-NET-ENI module • MicroLogix, CompactLogix, or FlexLogix with 1761-NET-ENI module • another EtherNet/IP PanelView terminal • Any device that can process CIP messages The PanelView terminal supports ac
Terminal Connections 12-39 Ethernet Connector The Ethernet connector is an RJ45, 10/100Base-T connector. The pinout for the connector is shown below: Pin RJ45 Connector 8 1 Pin Pin Name 1 TD+ 2 TD- 3 RD+ 4 NC 5 NC 6 RD- 7 NC 8 NC When to use a straight-through and cross-over pin-out: • Direct point-to-point 10/100Base-T cables, with cross over pin-out (1-3, 2-6, 3-1, 6-2), connect the PanelView Ethernet port directly to another SLC 5/05 Ethernet port (or a computer 10/100Base-T port).
12-40 Terminal Connections Typical EtherNet/IP Configuration The following illustration shows a ControlLogix Controller (with 1756-ENET/B modules), a PLC-5E controller, SLC 5/05, a MicroLogix/CompactLogix/FlexLogix (with 1761-NET-ENI module), and an Ethernet PanelView terminal connected to an EtherNet/IP network. Note that each node has a unique IP address. MicroLogix, FlexLogix, or CompactLogix with 1761-NET-ENI Module PLC-5E Controller ControlLogix 5550 Controller SLC 5/05 10.0.0.
Terminal Connections PanelView 300 Micro Terminal Connections 12-41 This section describes how to connect the PanelView 300 Micro terminal.
12-42 Terminal Connections Connecting to an SLC, PLC-5, ControlLogix, MicroLogix 1500LRP, CompactLogix, or FlexLogix Directly connect the PanelView 300 Micro terminal to an SLC, PLC-5 ControlLogix, MicroLogix 1500LRP, CompactLogix, or FlexLogix processor using the following cables. Use DH-485 (SLC only) or DF1 protocols for communications.
Terminal Connections 12-43 Connecting to an Advanced Interface Converter DH-485 versions of the PanelView 300 Micro can operate on a DH-485 network through an Advanced Interface Converter (AIC+) module. Use the following cables. AIC+ PanelView 300 Micro 1761-CBL-PM02, 2711-CBL-PMxx (to Port 1 of AIC+) 1761-CBL-HM02, 2711-CBL-HMxx (to Port 2 of AIC+) 1761-CBL-AP00 1761-CBL-AM00 RS-232 Communications Port (to Port 1) (to Port 2) 1 2 Cable, Catalog No. 1761-CBL-AM00, Series C (.5 m, 1.
12-44 Terminal Connections Connecting to a Personal Computer (Application File Transfers) Transfer applications between a computer and PV300 Micro terminal using one of the following cables. TIP Applications for the PanelView 300 Micro terminal are developed using PanelBuilder32 Software (Catalog No. 2711-ND3, V3.60 or later). PanelView 300 Micro Personal Computer (Running PanelBuilder32) 1761-CBL-PM02 2711-CBL-PM05 2711-CBL-PM10 RS-232 Communications Port 1 2 Cable, Catalog No.
Terminal Connections 12-45 PanelBuilder32 Software Supports the direct transfer of application files from PanelBuilder32 using an RS-232 link. Windows PanelView File Transfer (WinPFT) Utility Supports the direct transfer of PanelBuilder32 application files from WinPFT over an RS-232 link. The WinPFT utility is included with the PanelBuilder32 Software. RSLinx software may be required to transfer applications to the terminal for DH-485 and DF1 protocols.
12-46 Terminal Connections Connecting a Computer or Printer to the Terminal Most of the PanelView terminals have an RS-232 serial port to: • download/upload applications over a serial link • and/or connect a printer that supports the IBM enhanced character set PanelView terminals that don’t have an additional RS-232 Printer Port include the 300 Micro, the 300 (except for DeviceNet), and the -xxA2/ -xxA5 versions of the 550/600 and 900 monochrome terminals.
Chapter 13 Troubleshooting and Maintenance Chapter Objectives This chapter tells how to isolate and correct common operating problems and perform routine maintenance tasks. • • • • • • equipment required using troubleshooting chart LED indicators cleaning display window replacing clock module replacing backlight TIP The PanelView 300 Micro has no internal components that are user accessible. The rear cover is not removable, do not attempt to remove the cover.
13-2 Troubleshooting and Maintenance Problem Terminal does not power up. Probable Cause(s) 1. Improper connection to power source. Corrective Action(s) 1. Verify wiring and connections to power source. 2. Incorrect input voltage level. 3. DC power wires reversed (DC terminals only). 4. Power terminal block not fully seated (PV300 terminals only). 2. Verify correct voltage is present at power terminals. 3. Make sure DC power positive and negative are connected to the proper terminals. 4.
Troubleshooting and Maintenance Problem No communications with computer. Probable Cause(s) 1. Communications (COMM) fault. 2. No SLC, network, or power supply connection at terminal’s DH-485 port. 3. Baud rates not set correctly. 4. Terminal node and maximum node numbers are not set correctly. 13-3 Corrective Action(s) 1. Check status of COMM LED. Verify cable connections using cable diagrams in Chapter 10. 2. Personal Computer Interface Converter (PIC) receives power from DH-485 connection.
13-4 Troubleshooting and Maintenance Problem Screen objects do not function.(1) Probable Cause(s) 1. Terminal not communicating with controller. 2. Terminal in screen saver mode. Corrective Action(s) 1. Check status of COMM LED. See problem ’No communications with SLC or PLC controller’ for more information. 2. Access Screen Setup from the terminal Configuration Mode to check if terminal is in Screen Saver Mode. Application file name appears as ******* on Terminal Info screen. 1.
Troubleshooting and Maintenance Indicators 13-5 On PanelView terminals (except PanelView 300 Micro), use the COMM and Fault LED indicators to isolate operating problems. The illustration below shows the location of these indicators on some terminals. See chapter 1 for LED locations on other terminals..
13-6 Troubleshooting and Maintenance Remote I/O LED Indications LED (1) Comm This pattern: Indicates: Solid Fill Normal operating state (no communication faults) No Fill Communications not functioning • Verify that baud rate and rack settings match the PLC settings • Verify proper terminal to controller connections • Verify that the PLC enables Remote I/O communications Fault (1) Blinking No communications established. PLC is in program mode.
Troubleshooting and Maintenance Cleaning the Display Window 13-7 To clean the display window: ATTENTION Use of abrasive cleansers or solvents may damage the window. Do not scrub or use brushes. 1. Disconnect power from the terminal at the power source. 2. Use a clean sponge or a soft cloth to clean the display with a mild soap or detergent. 3. Dry the display with a chamois or moist cellulose sponge to avoid water spots.
13-8 Troubleshooting and Maintenance Replacing the Clock Module The Real-Time Clock (RTC) module contains a lithium battery used only by the real-time clock. The battery is not used for application backup or input retention. The clock module has a typical life expectancy of 7 years. TIP The real-time clock on the PanelView 300 Micro terminal is not replaceable. The clock module replacement kits for the PanelView terminals are listed in Chapter 1 under Replacement Parts.
Appendix A Specifications PanelView 300 Micro Electrical DC Power Supply Voltage Limits Power Consumption 11 to 30V dc (24V nominal), Class 2 Power Supply 2.5W maximum (0.105A @24Vdc) Mechanical Enclosure NEMA Type 12/13, 4X (Indoor use only), IP54, IP65 Weight 284 grams (10 oz.) Dimensions mm Inches 133 (H) x 112 (W) x 48 (D) 5.23 (H) x 4.38 (W) x 1.87 (D) Installed Depth 35mm (1.
A-2 Specifications Character Sizes (Pixel size = 0.48 x 0.48 mm) Size in Pixels width x height) Characters/Row Maximum Rows Dimensions in mm Width x Height 4x6 31 10 1.9 x 2.9 6x8 20 7 2.9 x 3.8 6 x 16 20 3 2.9 x 7.7 6 x 24 20 2 2.9 x 11.5 12 x 8 10 7 5.8 x 3.8 12 x 16 10 3 5.8 x 7.7 12 x 24 10 2 5.8 x 11.5 18 x 8 6 7 8.6 x 3.8 18 x 16 6 3 8.6 x 7.7 18 x 24 6 2 8.6 x 11.
Specifications A-3 Environment Operating Temperature 0 to 55° C (32 to 131° F) Storage Temperature -25 to 85° C (-4 to 188° F) Relative Humidity (non-condensing) 5 to 95% at 0 to 55° C (32 to 131° F) Heat Dissipation 6 Watts (13 BTU/HR) Shock (operating/non-operating) 15G/30G Vibration (operating) 2G up to 2,000 Hz Character Sizes (Pixel size = 0.48 x 0.48 mm) Size in Pixels width x height) Characters/Row Maximum Rows Dimensions in mm Width x Height 4x6 31 10 1.9 x 2.9 6x8 20 7 2.
A-4 Specifications PanelView 550 Electrical DC Power Supply Voltage Limits Power Consumption Supply Voltage Limits (touch screen only) Power Consumption (touch screen only) 18 to 30V dc (24V dc nominal) 18 Watts, max. (0.75A @ 24V dc) 18 to 32V dc (24V dc nominal) 18 Watts, max. (0.
Specifications A-5 Environment Operating Temperature 0 to 55° C (32 to 131° F) Storage Temperature -20 to 70° C (-4 to 158° F) Relative Humidity (non-condensing) 5 to 95% at 0 to 30° C (32 to 86° F) 5 to 75% at 31 to 40° C (88 to 104° F) 5 to 50% at 41 to 55° C (106 to 131° F) Heat Dissipation 20 Watts (69 BTU/HR) for AC Power or DC Power Shock (operating/non-operating) 30G/50G Vibration (operating) 2G up to 2,000 Hz Character Sizes (Pixel size = 0.47 x 0.
A-6 Specifications PanelView 600 Color Keypad & Touch Electrical AC Power Supply Voltage Limits Power Consumption 85 to 264V ac, 43 to 63 Hz 60 VA maximum DC Power Supply Voltage Limits Power Consumption 18 to 32V dc (24V dc nominal) 24 Watts max. (1.0A @ 24V dc) Mechanical Enclosure NEMA Type 12/13, 4X (Indoor use only), IP54, IP65 LED Indicators COMM Fault Green Red Weight 2 kg (4.4 lbs) Dimensions mm inches 192 (H) x 290 (W) x 116 (D) 7.55 (H) x 11.40 (W) x 4.
Specifications A-7 Character Sizes (Pixel size = 0.36 x 0.37 mm) PanelView 600 Color Touch Only Size in Pixels width x height) Characters/Row Maximum Rows Dimensions in mm Width x Height 6x9 52 25 2.9 x 5.9 8 x 16 39 14 2.9 x 5.9 8 x 24 39 9 2.9 x 8.9 16 x 24 19 9 5.8 x 8.9 24 x 32 13 7 8.6 x 11.8 32x 40 9 5 11.5 x 14.8 Electrical DC Power Supply Voltage Limits Power Consumption 18 to 32V dc (24V dc nominal) 24 Watts max. (1.
A-8 Specifications Environment Operating Temperature 0 to 50° C (32 to 122° F) Storage Temperature -25 to 70° C (-13 to 158° F) Relative Humidity (non-condensing) 5 to 95% at 0 to 40° C (32 to 104° F) Heat Dissipation 17 Watts (577 BTU/HR) Shock (operating/non-operating) 15G/30G Vibration (operating) 2G up to 2,000 Hz Character Sizes (Pixel size = 0.35 x 0.
Specifications A-9 Mechanical Dimensions - PV900M/900C Keypad mm inches 249 (H) x 406 (W) x 112 (D) 9.80 (H) x 15.97 (W) x 4.40 (D) Dimensions - PV900M/900C Touch Screen mm inches 249 (H) x 336 (W) x 112 (D) 9.80 (H) x 13.24 (W) x 4.40 (D) Installed Depth - PV900M 97 mm (3.81 inches) 129 mm (5.06 inches) with memory card retainer 220 mm (8.65 inches) with memory card retainer and clearance to insert and remove memory card Installed Depth - PV900C 99 mm (3.89 inches) 131 mm (5.
A-10 Specifications Environment PV900C Operating Temperature 0 to 55° C (32 to 131° F) Storage Temperature -25 to 70° C (-13 to 158° F) Relative Humidity (non-condensing) 5 to 95% at 0 to 55° C (32 to 131° F) Heat Dissipation 39 Watts (133 BTU/HR) Shock (operating/non-operating) 15G/30G Vibration (operating) 1G up to 2,000 Hz Character Sizes PV900M (Pixel size = 0.33 x 0.33 mm) Size in Pixels width x height) Characters/Row Maximum Rows Dimensions in mm Width x Height 8 x 16 79 24 2.
Specifications PanelView 1000 Color & Grayscale A-11 Electrical AC Power - PV1000G and PV1000C Supply Voltage Limits Power Consumption 85 to 264V ac, 47 to 63 Hz 55 VA maximum DC Power - PV1000G and PV1000C Supply Voltage Limits Power Consumption 18 to 32 V dc (24V dc nominal) 24 Watts max. (1.0A @ 24V dc) Mechanical Enclosure NEMA Type 12/13, 4X (Indoor use only) IP54, IP65 LED Indicators COMM Fault Green Red Weight - PV1000G and PV1000C Keypad Touch 3.06 kg (6.7 lbs) 3.00 kg (6.
A-12 Specifications Environment Operating Temperature 0 to 55° C (32 to 131° F) Storage Temperature -25 to 70° C (-13 to 158° F) Relative Humidity (non-condensing) 5 to 95% at 0 to 55° C (32 to 131° F) Heat Dissipation 39 Watts (132 BTU/HR) for Grayscale and Color Shock (operating/non-operating) 15G/30G Vibration (operating) 2G up to 2,000 Hz Character Sizes PV1000G and 1000C (Pixel size = 0.33 x 0.
Specifications A-13 Display Type Color CRT Size 255 x 191 mm (10.0 x 7.5 in.
A-14 Specifications Communications DH-485 Network Baud Rate Distance Maximum 1200, 2400, 9600, 19.2K 1219 meters (4,000 feet) DH+ Network Baud Rate Distance Maximum 57.6K, 115.2K, 230.4K 3048 meters (10,000 feet) RS-232 or DH-485 Point-to-Point Baud Rates Distance Maximum 1200, 2400, 9600, 19.2K 6.1 meters (20 feet) Remote I/O Baud Rates Publication 2711-UM014E-EN-P 57.6K, 2,800 meters (10,000 feet) 115.
Specifications A-15 Agency Certifications 300 Micro 300 550 600 900M 900C 1000G 1000C 1400 Emissions (Class A: Industrial) EN50081-2:1993 x x x x x x x x x Immunity (Industrial) EN61000-6-2:1999 x x(1) x(1) x(1) x(1) x(1) x(1) x(1) x(1) Immunity (Industrial) EN50082-2:1995(2) x x x x x x x x Programmable Controllers Equipment Requirements and Tests) EN61131 2:1995 x x x x x x x x x x(3) x x x x x x Low Voltage Directive (Safety Sections of EN61131-2) U
A-16 Specifications Publication 2711-UM014E-EN-P
Appendix B Messages, Codes and Self-Test Numbers This appendix lists: • terminal messages and codes that may appear during terminal operation • description of self-test numbers Types of Terminal Messages Status Messages Indicate the terminal is performing an operation that may limit access to the terminal, such as an application download or a communication problem. The message disappears when the terminal completes the operation or when the condition is satisfied.
B-2 Messages, Codes and Self-Test Numbers General Terminal Messages Error Number Terminal Messages Type Meaning Recommended Action 200-206, 300, 318-321, 328, 329, 331, 346, 347, 355, 356, 358, 367, 404, 411, 416, 417, 421-425, 447-449, 457, 459, 700, 1105, 1111, 1113, 1115, 1207-1211, 2002-2009, 2016, 2018, 2021, 2028 and 2029 A fault has occurred. Error = X Minor Fault or Terminal Fault A minor fault was detected that could impact terminal operation or a terminal fault was detected.
Messages, Codes and Self-Test Numbers B-3 Error Number Terminal Messages Type Meaning Recommended Action 325 Unformatted card Reminder Memory card is unformatted, contains an unrecognizable format or is corrupt. Reformat the card or replace it with a new card. Try again. 326 No Card Inserted Reminder You tried to transfer data to/from a memory card but there is no card in the card slot. Install a memory card and try again.
B-4 Messages, Codes and Self-Test Numbers Error Number Terminal Messages Type Meaning Recommended Action 393 File not supported Reminder/File Transfer Status File is incompatible with the communication protocol of the terminal. In PanelBuilder32, select the Setup tab on the Application Settings dialog and make sure the protocol matches your terminal. 394 File not supported Reminder/File Transfer Status File is incompatible with the terminal’s firmware.
Messages, Codes and Self-Test Numbers B-5 Error Number Terminal Messages Type Meaning Recommended Action 1127 Password changed Reminder Password change is effective. You must use new password for security access. 2005 Application file: Insufficient RAM Terminal Fault Application file may be too large. Try again. If possible, reduce the size of the application. 2007 - 2010 Application file contains errors Terminal Fault Application contains incompatible data.
B-6 Messages, Codes and Self-Test Numbers ControlNet Terminal Messages See Terminal Codes for messages below Error Number Terminal Messages Type Meaning Recommended Action 634 PanelView offline Comm Warning PanelView is offline. Check connections 634 Write fail. Comm Warning PanelView is communicating with the controller. The data table address does not exist. Check / define data table address in the controller. 634 Write timeout.
Messages, Codes and Self-Test Numbers B-7 Remote I/O Terminal Messages Error Number Terminal Messages Type Meaning Recommended Action 661 Timeout - No Block Transfer Writes Comm Status The PLC is communicating with the terminal, but the PanelView is not receiving BTW requests required by the application. Check ladder logic for missing BTW instructions (instructions are not enabled) or addressing errors. Check for logic controller errors.
B-8 Messages, Codes and Self-Test Numbers DH+ Terminal Messages Error Number Terminal Messages Type Meaning Recommended Action 675 or 684 Required network node(s) not found Comm Status The network is active, but the logic controller(s) are not located at the expected nodes. Verify that the logic controller(s) required by the application are at the expected node addresses and that the communication parameters are set properly. 676 or 685 File access error Comm Status 1.
Messages, Codes and Self-Test Numbers B-9 DF1 Terminal Messages Error Number Terminal Messages Type Meaning Recommended Action 675 or 682 Required network node(s) not found Comm Status The network is active, but the logic controller(s) are not located at the expected nodes. Verify that the logic controller(s) required by the application are at the expected node addresses and that the communication parameters are set properly.
B-10 Messages, Codes and Self-Test Numbers DeviceNet Comm Status Code Indicates: Recommended Action 5 Message Overrun. Message traffic from the PanelView is being generated quicker than it is possible to send the data. Occurs with large I/O sizes when Change-Of-State is being used and state changes are occurring very quickly or if polling too fast. Slow down I/O polling or the state changes generating Change-of-State I/O messages. Use Cyclic I/O at a fast heartbeat rate rather than Change-of-State.
Messages, Codes and Self-Test Numbers B-11 DeviceNet Alert Codes Indicates: Recommended Action 12 Invalid ASA Number (0x00000000 or 0xFFFFFFFF). Occurs if the flash memory is corrupt or an invalid ASA number was programmed. Clear the message. The message occurs each time the terminal is reset. The terminal operates normally but you should correct the problem. Contact technical support. 14 Get Next Scan Item Failed in peer mode. Should not occur in normal operation. Clear the message.
B-12 Messages, Codes and Self-Test Numbers General Codes General Terminal Alert Code Alert Type Indicates: Recommended Action 603 Critical fault File download error Reset the terminal. If problem occurs again, contact technical support. 9020 Critical fault An internal fault occurred. Reset the terminal. If problem occurs again, contact technical support. ControlNet Codes These errors appear at the top of the application screen or on the terminal’s configuration screen.
Messages, Codes and Self-Test Numbers B-13 These messages appear on the terminal screen as DC Error=xx. If you get an alert number that is not listed here, contact technical support. ControlNet Alert Codes Alert Type Indicates: Recommended Action 9000 Critical fault Interface startup failed. Contact technical support. 9003 Critical fault CIP S/N is not valid. Contact technical support. 9004 Critical fault Out of buffers. Contact technical support.
B-14 Messages, Codes and Self-Test Numbers Error Number Terminal Messages Type Meaning Recommended Action 16388 CIP S/N is not valid Critical fault. DC incorrectly configured. Contact technical support. 16389 Out of buffers Critical fault. No buffers are available for read or write operations. Contact technical support.
Messages, Codes and Self-Test Numbers B-15 Error Number Terminal Messages Type Meaning Recommended Action 16410 Too many clients attempted to connect to server Critical Fault Internal error has occurred. Contact technical support. 16411 XS-WD creation error Critical Fault Internal error has occurred. Contact technical support. 16412 XS-WD start error Critical Fault Internal error has occurred. Contact technical support.
B-16 Messages, Codes and Self-Test Numbers Remote I/O Communication Loss When communication fails on a Remote I/O network: • Object states are maintained and the message "No PLC Communication" is displayed on the screen. • If Block Transfers are defined for the application, but no BTR or BTW instructions are received, another message appears when the Block Transfer Timeout occurs. These messages continue to display until communications is established.
Messages, Codes and Self-Test Numbers Test Number Indicates 25 Firmware not compatible with boot code 26 Firmware not compatible with hardware 30 Watchdog test 31 Stuck key test 32 Real time clock test 33 LCD RAM failed 34 Performed CRC extended firmware check TIP B-17 You may not see all of these test numbers during a powerup. If a test fails, the terminal displays: ERROR! FEHLER! ERREUR! ERRORE! The following test numbers appear only if a problem occurs.
B-18 Messages, Codes and Self-Test Numbers Publication 2711-UM014E-EN-P
Appendix C European Union Directive Compliance If the PanelView Operator Terminals are installed within the European Union or EEA regions and have the CE mark, the following regulations apply.
C-2 European Union Directive Compliance Intended Use of Product According to these Standards, the factor which determines, for EMC purposes, whether a product is deemed to be "Industrial" rather than "Residential, commercial or light industrial", is given in clause 1 of EN50081-2 as follows: Apparatus covered by this standard is not intended for connection to a public mains network supplied from a high- or medium-voltage transformer dedicated for the supply of an installation feeding a manufacturing or si
Glossary adapter ControlNet device which responds to scanner messages (also called slave device). address 1) A character string that uniquely identifies a memory location. 2) A character string that uniquely identifies the physical location of an input or output circuit. application In the context of PanelBuilder32, an application is a logical arrangement of screens which replace the functions of a control panel and consist of push buttons, data entry objects, control lists and indicators.
Glossary 2 controller A unit, such as a programmable controller or relay panel, that controls machine or process elements. cursor keys Up, down, left, right arrows on the terminal keypad. These keys are used to move a selection cursor or the active object indicator bar. DF1 Allen-Bradley communication protocol based on an ANSI X3.28-1976 specification. download See upload/download. DH-485 link Data Highway 485 link. An Allen-Bradley token-passing carrier-band link for a local area network.
Glossary 3 EMI Electromagnetic Interference. Any electromagnetic disturbance that interrupts, obstructs, or otherwise impairs the performance of electronic equipment. EPROM Erasable Programmable Read-only Memory. A PROM that can be erased, usually with ultraviolet light, then re-programmed with electrical signals. As with all PROMs, it is nonvolatile random-access memory. EEPROM (flash) Electrically-Erasable PROM. A type of PROM that can be erased and re-programmed by electrical signals.
Glossary 4 keeper The network controller of a ControlNet network. keypad Set of 14 keys (numeric 0-9, decimal point, backspace, minus, and enter) to the right of the display on keypad terminals. These keys are used to enter data. LED Light-Emitting Diode. Memory Card A storage medium which can store a PanelView application and/or a font file. MicroLogix An Allen-Bradley programmable controller.
Glossary 5 PanelBuilder32 software A Windows program used to develop applications which run in PanelView terminals. PanelView terminal An Allen-Bradley keypad or touch screen terminal providing the operator interface to the logic controller when an application is executing. PC 1) Personal Computer. 2) Programmable Controller. 3) Printed Circuit. PCCC Acronym for Programmable Controller Communication Commands.
Glossary 6 remote I/O 1) I/O connected to a processor across a serial link. With a serial link, remote I/O can be located long distances from the processor. remote I/O link A serial link for carrying I/O data between a PLC or SLC processor/scanner and remote I/O adapters. repeater Two-port component that receives and transmits all data from one segment to another. restore To load an application from a memory (PC) card.
Glossary 7 screen 1) the viewing surface on which data is displayed. 2) The visual image on a screen. segment Trunk-cable sections connected through taps with terminators at each end and no repeaters. SLC An Allen-Bradley programmable controller with a name that has the prefix SLC. SMAX Highest ControlNet node address which can communicate during the scheduled portion of the network update interval. subnet mask A 32 value forming the PanelView terminal’s subnet mask.
Glossary 8 unscheduled messages Messages that are sent on an as needed basis. Unscheduled messages are sent during the unscheduled portion of the network update interval. UMAX Highest ControlNet node address which can communicate during the unscheduled portion of the network update interval. upload/download Commonly referred to the reading/writing across a link relatively large blocks of data from one device to another.
Index A AC power connecting 2-3 electrical ratings 2-3 accessories antiglare overlay 1-36 backlight lamp 1-39 cables 1-36–1-38 file transfer utility 1-37 function key legend kits 1-35 memory card retainer 1-36 memory cards 1-36 mounting clips 1-40 mounting studs 1-40 real time clock 1-39 wallmount power supply 1-37 alarms content 5-18 description 1-35 antiglare overlay 1-36 application files running 1-32 settings 3-1 ASCII entry controls description 5-8 entering data 5-8–5-11 scratchpad in other languages 5
2 Index DC power connecting 2-5–2-6 electrical ratings 2-5 declarations of conformity C-2 DeviceNet communications active baud rate 3-12 active node 3-11 available terminals 1-2–1-9 connecting a computer 12-46 connecting a printer 12-46 DeviceNet ports 12-35 input size 3-12 LED indicators 3-13 making connections 12-36 output size 3-13 DF1 communications available terminals 1-2–1-9 baud rate 3-14 Comm LED 3-14 compatible controllers 12-25 configuration screen 3-13 connecting to a CompactLogix 12-28 connect
Index clearances 10-5 cutout dimensions 10-6 enclosures 10-2 mounting dimensions 10-4 panel installation 10-7 required tools 10-2 Installing the PanelView 1400 clip mounting 11-5 cutout dimensions 11-4 enclosures 11-1 mounting dimensions 11-2 required tools 11-1 stud mounting 11-7 Installing the PanelView 300 clearances 7-4 cutout dimensions 7-3 enclosures 7-2 mounting dimensions 7-2 panel installation 7-5 required tools 7-2 Installing the PanelView 300 Micro clearances 6-3 cutout dimensions 6-3 enclosures
4 Index scratchpad 5-6 P PanelView 1000 connecting AC power 2-3 connecting DC power 2-5 features 1-24 installation 10-1 resetting 2-8 screen adjustments 3-22 screen saver 3-22 specifications A-11 PanelView 1400 aligning the touch grid 3-27 connecting AC power 2-3 features 1-28 installation 11-1 resetting 2-8 screen adjustments 3-26 specifications A-12 PanelView 300 connecting DC power 2-5 features 1-10, 1-11 resetting 2-8 specifications A-1 PanelView 300 Micro connecting to AIC+ 12-43 connecting to DNI 1
Index configuration screen 3-8 connecting a computer 12-46 connecting a printer 12-46 connecting to a Remote I/O scanner 12-9 last chassis 2-11, 3-8 out-of-box application 2-10 Pass-Through 2-11, 3-8 rack number 2-11, 3-8 rack size 2-11, 3-8 Remote I/O port 12-7 RS-232 port 12-7 starting module group 2-11 supported controllers 12-8 resetting PanelView 1000 2-8 PanelView 1400 2-8 PanelView 300 2-8 PanelView 300 Micro 2-8 PanelView 550 2-8 PanelView 600 2-8 PanelView 900 2-8 RS-232 (DH-485) communications a
6 Index Publication 2711-UM014E-EN-P
Index 7 Publication 2711-UM014E-EN-P
8 Index Publication 2711-UM014E-EN-P
Rockwell Automation Support Rockwell Automation provides technical information on the web to assist you in using its products. At http://support.rockwellautomation.com, you can find technical manuals, a knowledge base of FAQs, technical and application notes, sample code and links to software service packs, and a MySupport feature that you can customize to make the best use of these tools.
