Operation/Reference Guide AVS-SL-PR-0401-0601 Solecis Presentation Switcher 4x1 RGBHV, 6x1 SVID, 10x1 Stereo, CP S o l e ci s S w i t c h e r s L a s t Upda t e d: 10 /2 3 /20 0 8
AMX Limited Warranty and Disclaimer This Limited Warranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partner which include AMX Dealers, Distributors, VIP’s or other AMX authorized entity.
Safety Instructions Safety Instructions Overview Please read these instructions before using your Procon switcher. Failure to comply with these instructions could result in fire, electrical shock, personal injury, death, or damage to the equipment. Power Source Use only a three-wire grounding type source. The power source should not exceed 264VAC. Do not remove under any circumstances the ground wire. Power Cord Use only the cord shipped with the unit.
Safety Instructions AVS-SL-PR-0401-0601
Table of Contents Table of Contents Safety Instructions .............................................................................................. a Overview .................................................................................................................. a Power Source............................................................................................................ a Power Cord...................................................................................................
Table of Contents Mute ON ........................................................................................................................ 8 Mute OFF ....................................................................................................................... 8 Front Panel Disable ........................................................................................................ 8 Front Panel Enable .....................................................................................
Overview Overview The Solecis AVS-SL-PR-0401-0601 Presentation Switcher (FG1330-2011-01) combines switching of PC, computer, video and audio for presentation and conference rooms, home cinema, AV Rental Companies and any environment where a number of mixed source types need to be displayed. The AVS-SL-PR-0401-0601 features a total of ten inputs and a programmable serial output for controlling projectors, plasma displays and other display devices. FIG.
Overview AVS-SL-PR-0401-0601 Specifications (Cont.) Sync Output Level: TTL Impedance: 75 ohm Video Video Inputs: 6 YC or Composite Connector: Phono/RCA/Cinch 4Pin Din S-Video Level: Analogue Max Input: 1V P-P Impedance: 75 Ohm Bandwidth: 50MHz -3dB Return Loss: -30dB@1MHz, -22dB@5MHz Differential Phase Error: 0.05% Differential Gain Error: 0.
Connections Connections Typical Installation For Use With a Projector Connect the RGB, Video and Audio sources to the Input sockets on the rear panel of the unit. The RGB/Video inputs are 75 ohm terminated and the audio inputs 47Kohm terminated. The RGB/Video and audio outputs are fully 75 ohm and 600 ohm driven respectively for connection to long cable runs. It is imperative that the input sources are fully compatible with the display and sound devices.
Connections 4 AVS-SL-PR-0401-0601
Operation Operation Front Panel Source Selection To select a Source press the Button corresponding to the numbered Input. The button will illuminate. A PC input will be routed to the PC output sockets. A selected Video Input will also be routed to its respective Composite or S-Video output. If a PC input is selected then the last selected video input will remain on its respective output and vice versa. The Audio Channel will switch to the highlighted Input.
Operation Input mode only When the 2011 is powered up a mode command will be sent to a display on the first press of any Input select button. The command will either be RGB, Composite or S-Video depending on the button pressed. This will ensure a display device is set to the correct mode to display the input selected. Each time a different source type is selected then a mode command will be sent to the display device.
SET Commands SET Commands Input Switching The following command switches input sources. Byte 1 Byte 2 Byte 3 Byte 4 Byte 5(optional) (Header) (Address) (Video Input) (Audio Input) RGB Delay (see note) E8 00 to FF 00 to 0A 0 to OA 01 to FF The Audio Inputs can be switched independently from the Video.
SET Commands Attenuation (Changes Level on selected Input only) The Volume level increases 0.5db each time the following command is sent: Byte 1 Byte 2 Byte 3 (Header) (Address) (Increase) E8 00 to FF 0D The Volume level decreases 0.
GET Commands GET Commands Switch and Volume Status Feedback Transmit Byte 1 Byte 2 Byte 3 (Header) (Address) EF 00 to FF 80 Byte 2 Byte 3 Receive Byte 1 Byte 4 Byte 5 (Header) (Address) C8 00 to FF PC or Video Input Audio input Input volume level 0= Blank 1 to 4 = PC I/P 5 to 0A= Vid I/P The same string will be transmitted each time an input is selected.
GET Commands Identity Command Sending this command: Byte 1 Byte 2 Byte 3 Byte 4 F2 09 EA 80 The unit will return: Byte 1 Byte 2 6E 10 04 =2010 AVS-SL-PR-0401-0601
Device Manager Device Manager Overview This software can be used for configuring the 2011 to control external display devices. It is downloadable from our website www.procon.co.uk under support. Connection Connect the serial port of the PC as follows: PC (D9) 2011 Pin 5 gnd Pin 2 tx Pin 3 rx Run Device Manager. If the connection is correct the software will automatically detect the 2011. Click on the 2011 and a virtual panel will appear (FIG. 2): FIG.
Device Manager FIG. 4 Device Manager - Adding a Device to the Library The manufacturer's data sheet will be required. If the string needs to be transmitted more than once then select the number of times from the count drop-down list and set a suitable interval period. If the power on/off function is to be enabled then set a warm up/cool down time and click on Set/Enable. Finally click on Program Device to download the information. For operation see section on Display device serial output.
Device Manager AVS-SL-PR-0401-0601 13
10/08 ©2008 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX. AMX reserves the right to alter specifications without notice at any time. It’s Your World - Take Control™ 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 • 469.624.8000 • 469-624-7153 fax • 800.932.6993 technical support • www.amx.
