Operation/Reference Guide NXD-500i 5" Modero® Wall/Flush Mount Touch Panel with Intercom Touch Panels L a s t R e v i s e d : 7 /2 / 2 0 1 2
AMX Limited Warranty and Disclaimer This Limited Warranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partner which include AMX Dealers, Distributors, VIP’s or other AMX authorized entity.
AMX Software License and Warranty Agreement • LICENSE GRANT. AMX grants to Licensee the non-exclusive right to use the AMX Software in the manner described in this License. The AMX Software is licensed, not sold. This license does not grant Licensee the right to create derivative works of the AMX Software. The AMX Software consists of generally available programming and development software, product documentation, sample applications, tools and utilities, and miscellaneous technical information.
Table of Contents Table of Contents Introduction ........................................................................................................1 Key Features ................................................................................................................... 1 NXD-500i Specifications .......................................................................................... 2 Front Bezel Button.........................................................................................
Table of Contents Step 1: Configure the Panel’s Wired IP Settings..................................................... 30 IP Settings section - Configuring a DHCP Address over Ethernet ................................. 30 IP Settings section - Configuring a Static IP Address over Ethernet.............................. 31 Step 2: Choose a Master Connection Mode Setting ............................................... 31 Step 3: Configure an Ethernet Connection Type ..........................................
Table of Contents Password Settings Page ................................................................................................ 63 Sensor Settings ............................................................................................................. 64 Making the most of the Light bargraph ........................................................................ 65 Making the most of the Motion Sensor feature ............................................................
Table of Contents Font Styles and ID Numbers.......................................................................................... 80 Border Styles and Programming Numbers .................................................................... 80 TPD4 Border Styles by Name ........................................................................................ 81 Telnet Commands ................................................................................................... 82 set motion beep.........
Table of Contents ^GSN......................................................................................................................................... 97 ^ICO.......................................................................................................................................... 98 ^JSB .......................................................................................................................................... 98 ^JSI ..................................................
Table of Contents @TKP....................................................................................................................................... TPAGEON ............................................................................................................................... TPAGEOFF.............................................................................................................................. @VKB .............................................................................
Table of Contents ^ICM-MUTEMIC ...................................................................................................................... 122 ^ICM-SPEAKERLEVEL ............................................................................................................. 122 Panel IR Commands .............................................................................................. 123 ^IRM.......................................................................................................
Table of Contents Special escape sequences ........................................................................................... 137 Appendix B - Complex Script Support ............................................................139 Overview ..............................................................................................................
Introduction Introduction The NXD-500i 5" Modero Wall/Flush Mount Touch Panel with Intercom (FG2261-02) is a widescreen fullcolor mini-touch panel with full sound and intercom capability. This panel includes a built-in microphone, speakers, a mini-USB port for programming and audio output, and one NetLinx-programmable button.
Introduction NXD-500i Specifications Product Specifications Dimensions (HWD): • NXD-500i (with faceplate): 4.15" x 5.59" x 1.97" (10.50 cm x 14.20 cm x 5 cm) • CB-TP5i Rough-In/Wallbox (optional): 4.27" x 5.14" x 3.40" (10.86 cm x 13.06 cm x 8.64 cm) Power Requirements: • PoE Powered - No local Power Supply needed. • Max power draw: 5.5W.
Introduction Product Specifications (Cont.) Side Panel Components: • Ethernet 10/100 port: • RJ-45 port for 10/100 Mbps communication. The Ethernet port automatically negotiates the connection speed (10 Mbps or 100 Mbps), and whether to use half duplex or full duplex mode. Power is supplied through Power Over Ethernet (PoE) • NXD-500i panels communicate with the NetLinx Master using the ICSP protocol over Ethernet.
Introduction Front Bezel Button The NXD-500i has only one button on the front of the device, in the center of the button trim ring. This button has several uses: Press the button once to start a previously programmed function, or to turn off the display if not previously programmed. Press and hold the button for 6 seconds to put the device into Setup Mode (please see the Setup Page section on page 47 for more information).
Installation Installation Overview While the NXD-500i is designed to fit into pre-existing NXD-CV5 touch panel sites, the actual installation differs from that of the NXD-CV5 is several significant ways. The NXD-500i can be installed either directly into the (optional) CB-TP5i Rough-In Box or another solid surface environment, using either solid surface screws or the included locking tabs for different mounting options. The NXD-500i is contained within a clear outer housing known as the backbox (FIG. 3).
Installation Removing the Faceplate In certain circumstances, the Faceplate must be removed and replaced with a new faceplate. Because the device is installed against a wall, the faceplate must be removed carefully to prevent the two top prongs on the underside of the Faceplate from being broken. To remove the faceplate: 1. Gently lift up on the faceplate from the bottom. Do NOT pull up from the sides or the top. 2.
Installation Pre-Wall Installation of the Rough-In Box The CB-TP5i Rough-In Box (FG038-11) is an optional metallic box that is secured onto a stud/beam in a pre-wall setting, where no walls are present. Installation procedures and configurations can vary, depending on the installation environment. This section describes the installation procedures for the most common installation scenarios.
Installation Installing the NXD-500i within a Rough-In Box The Rough-In Box must be mounted prior to continuing this section. Refer to the procedures in the Pre-Wall Installation of the Rough-In Box section on page 7 for detailed pre-wall installation instructions. Verify that all necessary cables have been threaded through the knockouts on the left of the Rough-In Box and the connections have been tested prior to installation of the NXD-500i. 1. Remove the Faceplate bezel (A in FIG.
Installation The maximum recommended torque to screw in the locking tabs on the back box is 5 IN-LB [56 N-CM]. Applying excessive torque while tightening the locking tab screws, such as with powered screwdrivers, can strip out the tabs or damage the back box. 6. Connect both connectors to their corresponding locations along the left side of the NXD-500i touch panel. 7. Test the incoming wiring by attaching the panel connections to their terminal locations and applying power via the PoE Injector.
Installation Refer to the diagram for detailed installation dimensions as shown in FIG. 7. Cutting out the surface slightly smaller than what is outlined in the installation drawings, in order to make any necessary cutout adjustments, is highly recommended. 1. Prepare the area by removing any screws or nails from the drywall before beginning the cutout process. 2. Cut out the surface for the back box. Refer to the dimensions in FIG. 7 for more information. FIG.
Installation 4. Thread the incoming Ethernet and USB wiring from their terminal locations through the surface opening. Leave enough slack in the wiring to accommodate any re-positioning of the panel. 5. Connect both connectors to their corresponding locations along the left side of the NXD-500i touch panel. B A FIG. 8 Wall Mount panel (NXD-500i) installation view for drywall surfaces - top view 6.
Installation 10. The microphone cable is taped to the back box. Connect the microphone cable to its connector, making sure that the cable does not interfere with reattachment of the Faceplate. 11. Install the two Plastite screws attaching the NXD-500i to the back box (FIG. 5). 12. Place the Faceplate/Trim Ring assembly (A in FIG. 8) back onto the main NXD-500i unit (B in FIG. 8).
Installation Installing the NXD-500i into a Flat Surface using #4 screws Three #4 mounting screws (not included) are secured through circular holes located at the left and right sides of the NXD-500i. The most important thing to remember when mounting the NXD-500i is that the back box must be installed flush against the mounting surface. Refer to SP-2261-02 for detailed installation dimensions (reproduced in FIG. 9).
Installation 3. Remove the Faceplate/bezel (A in FIG. 10) from the main NXD-500i unit (B in FIG. 10) by gripping the faceplate and pulling up and out with gentle force. 4. Thread the incoming Ethernet and USB wiring from their terminal sources through the surface opening. Leave enough slack in the wiring to accommodate any re-positioning of the panel. 5. Connect all connectors to their corresponding locations along the left side of the un-powered NXD-500i touch panel.
Installation Installing an NXD-500i into a Rack Mount Kit (NXA-RK5) The NXA-RK5 is a 19" (48.26 cm) wide metal rack-mount (with black matte finish) measuring 3 rack units high. 1. Remove the Faceplate/Trim Ring assembly from the main NXD-500i unit. 2. Thread the incoming Ethernet and USB wiring from their terminal sources through the surface opening, leaving enough slack in the wiring to accommodate any re-positioning of the panel. 3.
Installation Wiring Guidelines for the NXD-500i Panel The NXD-500i panel utilizes the Power over Ethernet protocol, where it draws power directly from its Ethernet connection. Because of this, the panel has no need for standard power inputs or outputs. Ethernet/RJ-45 Port: Connections and Wiring FIG. 11 describes the blink activity for the Ethernet 10/100 Base-T RJ-45 connector and cable. The Ethernet cable is connected to the side of the Wall Mount panels.
NXD-500i Touch Panel Accessories NXD-500i Touch Panel Accessories Overview The PS-POE-AF (FG423-80) is a Power-over-Ethernet (PoE) power supply with integral DC Injector (FIG. 13). It provides DC power for one PoE-equipped device by "Injecting" DC power through the CAT5 ethernet cable. The PS-POE-AF supports the IEEE standard PoE pinout: Pins 4&5 Power (+) / Pins 7&8 Power (-). FIG.
NXD-500i Touch Panel Accessories Product Specifications PS-POE-AF Specifications Output Specifications Combined Line and Load Voltage Regulation Excluding Cord ±1% Ripple 1% Vp-p max. Transient Response • 0.5ms for 50% • Load Change Typical Protection • Foldback Overcurrent Protection • Short Circuit Protection Input Specifications AC Input Voltage Range 100-240VAC -10%, +6% Line Frequency 47-63Hz AC Input Current • 90VAC Input • 0.6A max.
NXD-500i Touch Panel Accessories PS-POE-AF Specifications (Cont.) Environmental Specifications Thermal Performance • • • • Operating Temperature 0° C to 40° C No Derating Convectional Cooling Non Vented Case Storage Temp -30° C to +85° C Relative Humidity Non-Condensing 5% to 95% Altitude 0-10,000 feet Pin Connections FIG.
NXD-500i Touch Panel Accessories 20 NXD-500i 5" Wall/Flush Mount Touch Panel with Intercom
Panel Calibration Panel Calibration Overview This section outlines the steps for calibrating the touch panel. Calibrating the panel before its initial use and after completing a firmware download is highly recommended. Modero panels are set up in the factory with specific demo touch panel pages. The first splash screen that appears indicates the panel is receiving power, beginning to load firmware, and preparing to display the default touch panel pages.
Panel Calibration If the calibration was improperly set and you cannot return to the Calibrate page through the panel’s firmware, this firmware page may be accessed via G4 WebControl, where you can navigate to the Protected Setup page and press the Calibrate button through a VNC window. This action causes the panel to go to the Calibrate page seen above, where the actual touch panel may be physically calibrated again using the above procedures.
Configuring Communication Configuring Communication Overview Communication between the Modero panel and the Master is done using either USB or ETHERNET (DHCP or Static IP). Ethernet communication can only be achieved via a direct Ethernet connection. Before commencing, verify that you are using the latest NetLinx Master and Modero panel firmware, and also verify you are using the latest versions of AMX’s NetLinx Studio and TPDesign4 applications. These are available at www.amx.com.
Configuring Communication Before continuing, open NetLinx Studio. This program assists in developing a System Number, Master IP/URL, and Master Port number. Refer to the NetLinx Master’s instruction manual for more information. 8. Obtain the System Number and Master IP Address from NetLinx Studio. This information must be specific for the system used with the configured Modero panel. 9. Press the Front Setup Access button for 4 seconds to open the Setup page. 10.
Configuring Communication Configuring and Using USB with a Virtual Master NetLinx Studio can be set up to run a Virtual Master where the PC acts as the Master by supplying its own IP Address for communication to the panel. The PC is first equipped with the USB driver, the panel is then configured for USB communication, and then Studio is configured to act as the Master.
Configuring Communication Step 3: Confirm and View Current AMX USB Device Connections The USB driver information can be confirmed via two different methods: Via the Control panel (previous steps 1 and 2) or Via the Unplug or Eject Hardware icon from the Taskbar. 1. Navigate to Start > Settings > Control Panel > and double-click the System icon to launch the System Properties dialog. 2. Select the Hardware tab and click on the Device Manager button to launch the Device Manager dialog.
Configuring Communication USB detection icon FIG. 20 USB Properties windows If a yellow exclamation point appears next to the AMX USB LAN LINK device (within the hardware devices section of the Unplug or Eject Hardware window), stop and close the USB operation. Reconnect the USB cable to the panel and repeat the setup procedures. Refer to the Troubleshooting section on page 129 for more detailed information.
Configuring Communication 4. Click the Communications Settings button to open the Communications Settings dialog (FIG. 22). FIG. 22 Communications Settings dialog box 5. Click on the NetLinx Master radio button in the Platform Selection section to indicate that this is working as a NetLinx Master. 6. Click on the Virtual Master radio box from the Transport Connection Option section to configure the PC to communicate directly with a panel.
Configuring Communication 12. The USB icon will appear to the left of the Connection Status icon to signify an active USB connection (FIG. 24). USB icon FIG. 24 USB icon If the G4 panel does not appear, refer to the Troubleshooting section on page 129 for more information. Step 5: Confirm and View the current AMX USB device connections Use the CC-USB Type-A to Mini-B 5-wire programming cable (FG10-5965) to provide communication between the mini-USB Program port on the touch panel and the PC.
Configuring Communication Configuring a Wired Ethernet Connection It is necessary to tell the panel as to which Master it should be communicating. This "pointing to a Master" is done via the System Settings page, where the IP Address, System Number and Username/Password information assigned to the target Master is configured. Until those parameters are configured, your Connection Status icon will remain red, indicating that it has no current connection to a Master.
Configuring Communication IP Settings section - Configuring a Static IP Address over Ethernet 1. Select Protected Setup > System Settings located on the lower left to open the System Settings page. 2. Locate the IP Settings section of this page. Check with your System Administrator for a pre-reserved Static IP Address assigned to the panel. This address must be obtained before Static assignment of the panel continues. 3.
Configuring Communication Step 3: Configure an Ethernet Connection Type When using Ethernet as the selected communication method, the NetLinx Master must first be set up with either a Static IP or DHCP Address obtained from either NetLinx Studio or your System Administrator. Before beginning: 1. Verify that the panel has been configured to communicate through an Ethernet cable connected from the panel to a valid Ethernet Hub.
Configuring Communication 4. Click the Communications Settings button to open the Communications Settings dialog (FIG. 22). 5. Click on the NetLinx Master radio button from the Platform Selection section to indicate that you are working as a NetLinx Master. 6. Click on the Virtual Master radio box from the Transport Connection Option section to indicate you are wanting to configure the PC to communicate with a panel. All other fields will be greyed out because the Master’s UI is not being used. 7.
Configuring Communication Master Connection Section - NetLinx Master Ethernet IP Address - URL Mode In this mode, enter the System Number (zero for an unknown System Number) and the IP/URL of the Master (the Master Port Number is defaulted to 1319). 1. In the System Settings page, press the Mode field until the choice cycles to URL. By selecting URL, the System Number field becomes read-only (grey) because the panel pulls this value directly from the communicating target Master, virtual or not.
Configuring Communication Master Connection Section - NetLinx Master Ethernet IP Address - Auto Mode In this mode, enter the System Number of the NetLinx Master. This mode instructs the Modero to search for a Master that uses the same System Number (assigned within the Master Connection section) and resides on the same Subnet as itself. 1. In the System Settings page, press the Mode field until the choice cycles to the word Auto. 2.
Configuring Communication FIG. 28 G4 Web Control page 5. Press the Enable/Enabled button until it toggles to Enabled (light blue color). 6. The Network Interface Select field is read-only and displays the method of communication to the web. Verify the selection of the proper interface connection, as this field does not auto-detect the connection type being used (see below). Wired is used when a direct Ethernet connection is being used for communication to the web.
Configuring Communication 12. Within the keypad, enter a unique numeric value to be assigned to the port being used by the VNC Web Server and press Done when finished. The default value is 5900. The remaining fields within the G4 Web Control Settings section of this page are read-only and cannot be altered. 13.
Configuring Communication G4 panels Compatible devices field showing G4 WebControl links Compression Options FIG. 30 Manage WebControl Connections page (populated with compatible panels) 6. Click on the G4 panel name link associated with the target panel. A secondary web browser window appears on the screen (FIG. 31). FIG. 31 Web Control VNC installation and Password entry screens 7.
Configuring Communication The G4 Web Control application is sent by the panel to the computer that is used for communication. Once the application is installed, this popup will no longer appear. This popup will only appear if connecting to the target panel using a different computer. 8. In some cases, a Connection Details dialog (FIG. 32) may appear that requests a VNC Server IP Address. This is the IP address of the target touch panel, not the IP of the Master.
Configuring Communication 40 NXD-500i 5" Wall/Flush Mount Touch Panel with Intercom
Upgrading Modero Firmware Upgrading Modero Firmware Overview Before beginning the Upgrade process: Set up and configure your NetLinx Master. Refer to the particular NetLinx Master Instruction Manual for detailed setup procedures. Calibrate and prepare the communication pages on the panel for use. Refer to the Panel Calibration section on page 21. Refer to the NetLinx Studio version 2.x or higher Help file for more information on uploading files. Configure the panel for a direct connection.
Upgrading Modero Firmware Step 2: Prepare NetLinx Studio for communication via the USB port 1. Launch NetLinx Studio (default location is Start > Programs > AMX Control Disc > NetLinx Studio). 2. Select Settings > Master Communication Settings from the Main menu to open the Master Communication Settings dialog (FIG. 33). FIG. 33 Master Communication Settings dialog box 3. Click the Communications Settings button to open the Communications Settings dialog (FIG. 34). FIG.
Upgrading Modero Firmware FIG. 35 Virtual NetLinx Master Settings dialog 7. Enter the System number (default is 1). 8. Click OK three times to close the open dialogs, save the settings, and return to the main NetLinx Studio application. 9. Click the OnLine Tree tab in the Workspace window to view the devices on the Virtual System. The default System value is one. 10. Right-click on the Empty Device Tree/System entry and select Refresh System to re-populate the list.
Upgrading Modero Firmware Virtual Master firmware version and device number NetLinx Studio version number Current Modero panel firmware version and device number FIG. 36 NetLinx Workspace window (showing the panel connection via a Virtual NetLinx Master) The panel firmware is shown on the right of the listed panel. Download the latest firmware file from www.amx.com and then save the Kit file to your computer. 4.
Upgrading Modero Firmware 9. Click the Reboot Device checkbox. This causes the touch panel to reboot after the firmware update process is complete. The reboot of the panel can take up 30 seconds after the firmware process has finished. 10. Click Send to begin the transfer. The file transfer progress is indicated on the bottom-right of the dialog (B in FIG. 37). 11. As the panel is rebooting, temporarily unplug the USB connector on the panel until the panel has completely restarted. 12.
Upgrading Modero Firmware 46 NXD-500i 5" Wall/Flush Mount Touch Panel with Intercom
Setup Pages and Descriptions Setup Pages and Descriptions Overview This section describes the Setup and Protected Settings pages and their specific functional elements. Setup Navigation Buttons The Setup Navigation Buttons (FIG. 38) appear on the left of the panel screen when the Setup page is currently active. Press to access the Protected Setup page for panel calibration and to access security release passwords and connection settings.
Setup Pages and Descriptions Setup Page Exit: Returns to the Main touch panel page. In this case, the previous page is the default Main page. Wired icon: The icon to the left of the Connection Status Icon displays that the current connection to the Master is Wired (image of three networked computers). Connection Status icon: This visual display of the connection status allows the user to have a current update of the panel’s connection status regardless of what page is currently active.
Setup Pages and Descriptions Information Pressing and holding the Information button provides a menu to select either the Panel Information page or the Panel Information page (FIG. 40). Select either option to access that page. FIG. 40 Information menu Panel Information Page The Project Information page displays the TPDesign4 (TPD4) project file properties currently loaded on the selected Modero panel (FIG. 41).
Setup Pages and Descriptions Project Information Page (Cont.) AMX IR Ports: Displays the AMX 38 kHz IR channel port used by the IR receiver on the panel. • This information is pulled by the panel from AMX IR Receivers section of the TPD4 Project Properties > IR Emitters & Receivers tab. • For IR reception, this is the port that reports a push on for the corresponding IR code. • IR receivers and transmitters on G4 panels share the device address number of the panel.
Setup Pages and Descriptions Panel Information Page (Cont.) High Channel: Displays the high channel (channel count) value for the panel. High Level: Displays the high level (level count) value being used by the panel. Serial Number: Displays the specific serial number value assigned to the panel. Setup Pages Version: Displays the type and version of the Setup pages being used by the panel. Screen Width: Displays the pixel width being used to display the incoming signal on the Modero panel.
Setup Pages and Descriptions The elements of the Time & Date Settings page are as follows: Time & Date Settings Page Back: Returns to the previously active touch panel page without saving changes. Wired icon: The icon to the left of the Connection Status Icon displays that the current connection to the Master is Wired (image of three networked computers).
Setup Pages and Descriptions Audio Settings Page Back: Saves the changes and returns to the previously active touch panel page. Wired icon: The icon to the left of the Connection Status Icon displays that the current connection to the Master is Wired (image of three networked computers). Connection Status icon: This visual display of the connection status allows the user to have a current visual update of the panel’s connection status, regardless of what page is currently active.
Setup Pages and Descriptions Protected Setup Navigation Buttons The Protected Setup navigation buttons (FIG. 45) appear on the left of the panel screen when the Protected Setup page is currently active. Press to access the System Settings page to configure communication settings for the NetLinx Master and the panel. Press to access the Calibrate page to calibrate the panel.
Setup Pages and Descriptions Protected Setup Page (Cont.) Options: Allows selection of various touch panel features: • The Function Show button enables the display of the channel port and channel code in the top left corner of the button, the level port and level code in the bottom left corner, and the address port and address code in the bottom right corner (see FIG. 48 for an example of the function locations). • Use the Page Tracking button to toggle page tracking.
Setup Pages and Descriptions Channel Code Number Channel Port Channel Code Number Channel Port 3,132 2,8 Slider Address Port Button Level Port 7,10 4,9 3,50 Channel Code Number Level Port Address Code Number Address Port 1,8 Channel Code Number Address Code Number FIG. 48 Button/slider Function Show example Security Settings The Security button on the Protected Setup page has three settings: Standard, Secure, and DoD. Pressing the button opens the Panel Security Setting popup window (FIG.
Setup Pages and Descriptions A transition from one security mode to another will reset the Protected/Web Control/ remote login password to the default value for the current security mode (please refer to the default passwords above). A transition to Secure or DoD mode will disable G4 Web Control. Although the security password features are immediate, a reboot must occur for all the new security mode features to fully take effect.
Setup Pages and Descriptions System Settings Page (Cont.) IP Settings: (Cont.) Primary DNS: Sets the address of the primary DNS server used for host name lookups. • DNS (Domain Name System) is software that lets users locate computers on a local network or the Internet (TCP/IP network) by host and domain. The DNS server maintains a database of host names for its domain and their corresponding IP Addresses. Secondary DNS: Sets a secondary DNS value to the panel.
Setup Pages and Descriptions Calibrate Page The Calibrate page (FIG. 51) allows you to calibrate the touch panel for maximum sensitivity. Press and hold the Front Setup Access button for 6 seconds to access the Calibrate page. Press the crosshairs to calibrate the panel and return to the last active firmware page. FIG. 51 Calibrate page If the calibration was improperly set and the Calibrate page cannot be reached through the panel’s firmware, this firmware page may be accessed via G4 Web Control.
Setup Pages and Descriptions G4 Web Control Settings Page Back: Saves the changes and returns to the previously active touch panel page. Wired icon: The icon to the left of the Connection Status Icon displays that the current connection to the Master is Wired (image of three networked computers). Connection Status icon: This visual display of the connection status allows the user to have a current visual update of the panel’s connection status regardless of what page is currently active.
Setup Pages and Descriptions Refer to the Using G4 Web Control to Interact with a G4 Panel section on page 35 for more detailed instructions on how to use the G4 Web Control page with the new web-based NetLinx Security application. Other Settings Holding down the Other Settings button provides a menu to select the Image Caching page, the Password Settings page, the Sensor Settings page, or the SIP Settings page (FIG. 54). Select either option to access that page. FIG.
Setup Pages and Descriptions The elements of this page are as follows: Cache Settings Page Back: Saves all changes and returns to the previous page. Wired icon: The icon to the left of the Connection Status Icon displays that the current connection to the Master is Wired (image of three networked computers). Connection Status icon: The icon in the upper-right corner of each Setup page shows online/offline state of the panel to the master. • Bright red - disconnected • Bright green - connected.
Setup Pages and Descriptions Setting the image cache In the Protected Setup page: 1. Press the Cache button in the Other Settings popup menu. This opens the Cache Settings page. 2. Set the cache expiration in the field Flash/RAM Cache Expires. The Up and Down arrows increment through the available time frames. 3. Press the Enable button to turn on image caching. The button is illuminated when enabled. Flash memory may be allocated for image caching, but RAM cache is always enabled.
Setup Pages and Descriptions Password Settings Page (Cont.) In Panel Password Change: Accesses the alphanumeric values associated to particular password sets. The PASSWORD 1, 2, 3, 4 and 5 (protected) buttons open a keyboard to enter alphanumeric values associated to the selected password group. Note: Clearing Password #5 removes the need to enter a password before accessing the Protected Setup page. Sensor Settings The Sensor Settings page (FIG.
Setup Pages and Descriptions Sensor Settings (Cont.) Motion Sensor: Provides the following fields: • The Motion Detection field displays a reactive button that changes color (illuminates) when motion is detected by the Modero panel’s front motion sensor. • The Motion Sensor Port field indicates the port used to report the motion sensor channel back to the NetLinx Master (set in TPD4) (read-only).
Setup Pages and Descriptions SIP Settings Page The options on the SIP Settings page (FIG. 58) enable you to establish network settings for using your touch panel as an IP phone. With a CSG SIP Communications Gateway (FG2182-01, -02, -03), you can use your touch panel to make and receive local, long distance, and international phone calls, and have access to phone features like call waiting, caller ID, call forwarding, call queuing, and voice mail.
Setup Pages and Descriptions SIP Settings Page (Cont.) Proxy Address: This option enables you to enter the IP address or DNS name of the proxy server that you want to use to register. Port Number: The option displays the port you use to connect to the proxy server. The standard SIP port is 5060, but some providers use different ports. STUN Address: This option enables you to enter the IP address or DNS name of the Simple Traversal of UDP through NATs (STUN) server. This field is optional.
Setup Pages and Descriptions Tools The Tools button provides a menu to select either the Panel Connection Logs Page section on page 68, the Panel Statistics Page section on page 69, or the Connection Utility section on page 71. Select any of the options to access that page. FIG. 59 Tools popup menu Panel Connection Logs Page The options on the Panel Connection Logs page allows viewing and tracking of the connection history for the panel (FIG. 60). FIG.
Setup Pages and Descriptions Panel Connection Page (Cont.) Connection Status icon: The icon in the upper-right corner of each Setup page shows online/offline state of the panel to the master. • Bright red - disconnected • Bright green - connected. Blinks when a blink message is received to dark green every 5 seconds for half a second then go back to bright green. • Bright yellow - panel missed a blink message from the master. It will remain yellow for 3 missed blink messages and then turn red.
Setup Pages and Descriptions Panel Statistics Page Back: Saves all changes and returns to the previous page. Wired icon: The icon to the left of the Connection Status Icon displays that the current connection to the Master is Wired (image of three networked computers). Connection Status icon: The icon in the upper-right corner of each Setup page shows online/offline state of the panel to the master. • Bright red - disconnected • Bright green - connected.
Setup Pages and Descriptions Connection Utility The options on the Connection Utility popup window allow you to verify connection information and statistics for the panel (FIG. 62). FIG. 62 Connection Utility popup window Connection Utility Window Close: Closes the Connection Utility popup. Wired icon: The icon to the left of the Connection Status Icon displays that the current connection to the Master is Wired (image of three networked computers).
Setup Pages and Descriptions 72 NXD-500i 5" Wall/Flush Mount Touch Panel with Intercom
Programming Programming Overview The NXD-500i may be programmed, using the commands in this section, to perform a wide variety of operations using Send_Commands and variable text commands. A device must first be defined in the NetLinx programming language with values for the Device: Port: System In all programming examples - Panel is used in place of these values and represents all Modero panels).
Programming Page Commands (Cont.) @DPG Delete a specific popup page from specified popup group if it exists. Syntax: "'@DPG-;'" Variable: popup page name = 1 - 50 ASCII characters. Name of the popup page. popup group name = 1 - 50 ASCII characters. Name of the popup group. Example: SEND_COMMAND Panel,"'@DPG-Popup1;Group1'" Deletes the popup page ’Popup1’ from the popup group ’Group1’. @PDR Set the popup location reset flag.
Programming Page Commands (Cont.) @PPA Close all popups on a specified page. • If the page name is empty, the current page is used. • This command works in the same way as the ’Clear Page’ command in TPDesign4. Syntax: "'@PPA-'" Variable: page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On. Example: SEND_COMMAND Panel,"'@PPA-Page1'" Close all popups on Page1. @PPF Deactivate a specific popup page on either a specified page or the current page.
Programming Page Commands (Cont.) @PPM Set the modality of a specific popup page to Modal or NonModal. A Modal popup page, when active, only allows use of the buttons and features on that popup page. All other buttons on the panel page are inactivated. Syntax: "'@PPM-;'" Variables: popup page name = 1 - 50 ASCII characters. Name of the popup page. mode = NONMODAL converts a previously Modal popup page to a NonModal. MODAL converts a previously NonModal popup page to Modal.
Programming Page Commands (Cont.) @PSE Set the show effect for the specified popup page to the named show effect. Syntax: "'@PSE-;'" Variable: popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On. show effect name = Refers to the popup effect name being used. Example: SEND_COMMAND Panel,"'@PSE-Popup1;Slide from Left'" Sets the Popup1 show effect name to ’Slide from Left’. @PSP Set the show effect position.
Programming Page Commands (Cont.) PPOG Toggle a specific popup page on either a specified page or the current page. • Toggling refers to the activating/deactivating (On/Off) of a popup page. • If the page name is empty, the current page is used (see example 2). • This command works in the same way as the ’Toggle Popup’ command in TPDesign4. Syntax: "'PPOG-;'" Variable: popup page name = 1 - 50 ASCII characters. Name of the popup page. page name = 1 - 50 ASCII characters.
Programming Programming Numbers for Colors, Fonts, and Borders Colors can be used to set the colors on buttons, sliders, and pages. The lowest color number represents the lightest color-specific display and the highest number represents the darkest display. For example, 0 represents light red, and 5 is dark red. RGB Triplets and Names For Basic 88 Colors RGB Values for all 88 Basic Colors Index No. Name Red Green Blue Index No.
Programming Font Styles and ID Numbers Font styles can be used to program the text fonts on buttons, sliders, and pages. The following chart shows the default font type and their respective ID numbers generated by TPDesign4.
Programming TPD4 Border Styles by Name The TPDesign4 Touch Panel Design program has pre-set border styles that are user-selectable. The following number values may not be used for programming purposes when changing border styles. TPD4 border styles may ONLY be changed by using the name. TPD4 Border Styles by Name No. Border styles No.
Programming TPD4 Border Styles by Name (Cont.
Programming Telnet Commands (Cont.) cal light This command initiates a light sensor calibration routine. This routine takes 30 seconds to complete. During this routine, the firmware will record the maximum light value detected and use this value as the normal light level in which the panel will be operating. This will enable the panel's "auto-brightness" feature to operate correctly.
Programming "^" Button Commands (Cont.) ^BAT Append non-unicode text. Syntax: "'^BAT-,
Programming "^" Button Commands (Cont.) ^BCF Set the fill color to the specified color. Only if the specified fill color is not the same as the current color. Note: Colors can be set by Color Numbers, Color name, R,G,B,alpha colors (RRGGBBAA) and R, G & B colors values (RRGGBB). Refer to theRGB Values for all 88 Basic Colors table on page 79. Syntax: "'^BCF-,
Programming "^" Button Commands (Cont.) ^BDO Determines what order each layer of the button is drawn. Syntax: "'^BDO-,
Programming "^" Button Commands (Cont.) ^BMC Button copy command. Copy attributes of the source button to all the destination buttons. Note that the source is a single button state. Each state must be copied as a separate command. The section represents what attributes will be copied. All codes are 2 char pairs that can be separated by comma, space, percent or just ran together.
Programming "^" Button Commands (Cont.) ^BMF Set any/all button parameters by sending embedded codes and data. Syntax: "'^BMF-,
Programming "^" Button Commands (Cont.) ^BMF (Cont.) ’%GI’ = Set the bargraph invert/noninvert or joystick coordinate (0,1,2,3). See the ^GIV command on page 96 for more information. ’%GU’ = Set the bargraph ramp up time in intervals of 1/10 second. ’%GD’ = Set the bargraph ramp down time in 1/10 second. ’%GG = Set the bargraph drag increment. Refer to the ^GDI command on page 96 for more information.
Programming "^" Button Commands (Cont.) ^BMI Mask image is used to crop a borderless button to a non-square shape. This is typically used with a bitmap. Syntax: "'^BMI-,
Programming "^" Button Commands (Cont.) ^BMP Assign a picture to those buttons with a defined address range. Syntax: "'^BMP-,
Programming "^" Button Commands (Cont.) ^BOP Set the button opacity. The button opacity can be specified as a decimal between 0 - 255, where zero (0) is invisible and 255 is opaque, or as a HEX code, as used in the color commands by preceding the HEX code with the # sign. In this case, #00 becomes invisible and #FF becomes opaque. If the opacity is set to zero (0), this does not make the button inactive, only invisible.
Programming "^" Button Commands (Cont.) ^BRD Set the border of a button state/states.Only if the specified border is not the same as the current border. The border names are available through the TPDesign4 border-name drop-down list. Syntax: "'^BRD-,
Programming "^" Button Commands (Cont.) ^BVL Log-On/Log-Off the computer control connection. Syntax: "'^BVL-,'" Variable: variable text address range = 1 - 4000. connection = 0 (Log-Off connection) and 1 (Log-On connection). Example: SEND_COMMAND Panel,"'^BVL-500,0'" Logs-off the computer control connection of the button. ^BVN Set the computer control remote host for the specified address.
Programming "^" Button Commands (Cont.) ^CPF Clear all page flips from a button. Syntax: "'^CPF-'" Variable: variable text address range = 1 - 4000. Example: SEND_COMMAND Panel,"'^CPF-500'" Clears all page flips from the button. ^DPF Delete page flips from button if it already exists. Syntax: "'^DFP-,,'" Variable: variable text address range = 1 - 4000.
Programming "^" Button Commands (Cont.) ^GDI Change the bargraph drag increment. Syntax: "'^GDI-,'" Variable: variable text address range = 1 - 4000. bargraph drag increment = The default drag increment is 256. Example: SEND_COMMAND Panel,"'^GDI-7,128'" Sets the bargraph with variable text 7 to a drag increment of 128. ^GIV Invert the joystick axis to move the origin to another corner.
Programming "^" Button Commands (Cont.) ^GRU Change the bargraph ramp-up time in 1/10th of a second. Syntax: "'^GRU-,'" Variable: variable text address range = 1 - 4000. bargraph ramp up time = In 1/10th of a second intervals. Example: SEND_COMMAND Panel,"'^GRU-500,100'" Changes the bargraph ramp up time to 10 seconds. ^GSC Change the bargraph slider color or joystick cursor color.
Programming "^" Button Commands (Cont.) ^ICO Set the icon to a button. Syntax: "'^ICO-,
Programming "^" Button Commands (Cont.) ^JST Set text alignment using a numeric keypad layout for those buttons with a defined address range. The alignment of 0 is followed by ',,'. The left and top coordinates are relative to the upper left corner of the button. Syntax: "'^JST-,
Programming "^" Button Commands (Cont.) ^TEC Set the text effect color for the specified addresses/states to the specified color. The Text Effect is specified by name and can be found in TPD4. Note: Colors can be set by Color Numbers, Color name, R,G,B,alpha colors (RRGGBBAA) and R, G & B colors values (RRGGBB). Refer to the RGB Values for all 88 Basic Colors table on page 79. Syntax: "'^TEC-,
Programming "^" Button Commands (Cont.) ^UNI Set Unicode text. For the ^UNI command (%UN and ^BMF command), the Unicode text is sent as ASCII-HEX nibbles. Syntax: "'^UNI-,
Programming Button Query Commands Button Query commands reply with a custom event. Each button/state combination has one custom event. Each query is assigned a unique custom event type.
Programming These fields are populated differently for each query command. The text length (String Encode) field is not used in any command. Button Query Commands ?BCB Get the current border color. Syntax: "'?BCB-,
Programming Button Query Commands (Cont.) ?BCT Get the current text color. Syntax: "'?BCT-,
Programming Button Query Commands (Cont.) ?BOP Get the overall button opacity. Syntax: "'?BOP-,
Programming Button Query Commands (Cont.) ?BWW Get the current word wrap flag status. Syntax: "'?BWW-,
Programming Button Query Commands (Cont.) ?ICO Get the current icon index. Syntax: "'?ICO-,
Programming Button Query Commands (Cont.) ?JSI Get the current icon justification. Syntax: "'?JSI-,
Programming Button Query Commands (Cont.) ?TEC Get the current text effect color. Syntax: "'?TEC-,
Programming Button Query Commands (Cont.) ?TXT Get the current text information. Syntax: "'?TXT-,
Programming Panel Runtime Operation Commands (Cont.) @AKB Pop up the keyboard icon and initialize the text string to that specified. Keyboard string is set to null on power up and is stored until power is lost. The Prompt Text is optional. Syntax: "'@AKB-;'" Variables: initial text = 1 - 50 ASCII characters. prompt text = 1 - 50 ASCII characters.
Programming Panel Runtime Operation Commands (Cont.) @AKR Remove the Keyboard/Keypad. Remove keyboard or keypad that was displayed using 'AKEYB', 'AKEYP', 'PKEYP', @AKB, @AKP, @PKP, @EKP, or @TKP commands. Syntax: "'@AKR'" Example: SEND COMMAND Panel,"'@AKR'" Removes the Keyboard/Keypad. BEEP Output a beep. Syntax: "'BEEP'" Example: SEND COMMAND Panel,"'BEEP'" Outputs a beep. BRIT Set the panel brightness. Syntax: "'BRIT-'" Variable: brightness level = 0 - 100.
Programming Panel Runtime Operation Commands (Cont.) PKEYP Present a private keypad. Pops up the keypad icon and initializes the text string to that specified. Keypad displays a '*' instead of the numbers typed. The Prompt Text is optional. Syntax: "'PKEYP-'" Variables: initial text = 1 - 50 ASCII characters. Example: SEND COMMAND Panel,"'PKEYP-123456789'" Pops up the Keypad and initializes the text string '123456789' in '*'. @PKP Present a private keypad.
Programming Panel Runtime Operation Commands (Cont.) @TKP Present a telephone keypad. Pops up the keypad icon and initializes the text string to that specified. The Prompt Text is optional. Syntax: "'@TKP-;'" Variables: initial text = 1 - 50 ASCII characters. prompt text = 1 - 50 ASCII characters. Example: SEND COMMAND Panel,"'@TKP-999.222.1211;Enter Phone Number'" Pops-up the Keypad and initializes the text string '999.222.1211' with prompt text 'Enter Phone Number'.
Programming Input Commands These Send Commands are case insensitive. Input Commands ^CAL Put panel in calibration mode. Syntax: "'^CAL'" Example: SEND COMMAND Panel,"'^CAL'" Puts the panel in calibration mode. ^KPS Set the keyboard passthru. Syntax: "'^KPS-'" Variable: pass data: = Disables the keyboard. 0 = Pass data to G4 application (default). This can be used with VPC or text areas. 1 - 4 = Not used. 5 = Sends out data to the Master.
Programming Embedded codes The following is a list of G4-compatible embedded codes: Embedded Codes 116 Decimal numbers Hexidecimal values Virtual keystroke 8 ($08) Backspace 13 ($0D) Enter 27 ($1B) ESC 128 ($80) CTRL key down 129 ($81) ALT key down 130 ($82) Shift key down 131 ($83) F1 132 ($84) F2 133 ($85) F3 134 ($86) F4 135 ($87) F5 136 ($88) F6 137 ($89) F7 138 ($8A) F8 139 ($8B) F9 140 ($8C) F10 141 ($8D) F11 142 ($8E) F12 143 ($8F) Num Lock
Programming Panel Setup Commands These commands are case insensitive. Panel Setup Commands @PWD Set the page flip password. Note: @PWD sets the level 1 password only. Syntax: "'@PWD-'" Variables: page flip password = 1 - 50 ASCII characters. Example: SEND COMMAND Panel,"'@PWD-Main'" Sets the page flip password to 'Main'. ^PWD Set the page flip password. Password level is required and must be 1 - 4.
Programming Dynamic Image Commands The following table describes Dynamic Image Commands. Dynamic Image Commands ^BBR Set the bitmap of a button to use a particular resource. Syntax: "'^BBR-,
Programming Dynamic Image Commands (Cont.) ^RMF Modify an existing resource. This command modifies any and all resource parameters by sending embedded codes and data. Since the embedded codes are preceded by a '%' character, any '%' character contained in the URL must be escaped with a second '%' character (see example). The file name field (indicated by a %F embedded code) may contain special escape sequences as shown in the ^RAF, ^RMF - Embedded Codes section on page 119.
Programming ^RAF, ^RMF - Embedded Codes (Cont.) Parameter Embedded Code Description refresh ’%R ’ The number of seconds between refreshes in which the resource is downloaded again. Refreshing a resource causes the button displaying that resource to refresh also. newest ’%N <0-1>’ The default value is 0 (only download the resource once). Set the newest file. A value of 1 means that only the most recent file matching the pattern is downloaded.
Programming Intercom Commands The following is a list of Intercom Commands: Intercom Commands ^MODEL? Sets model name. If the panel supports intercom hardware it will respond with its model name as shown in the response below. Older hardware or newer hardware that has intercom support disabled with not respond to this command. Syntax: SEND_COMMAND ,"'^MODEL?'" Variables: None.
Programming Intercom Commands (Cont.) ^ICE' Intercom end - this command terminates an intercom call/connection. Syntax: SEND_COMMAND ,"'^ICE'" Variables: None. Example: SEND_COMMAND TP1,"'^ICE'" SEND_COMMAND TP2,"'^ICE'" Terminates an intercom call between two panels. ^ICM-TALK See ^ICM section on page 121. Syntax: SEND_COMMAND ,"'^ICM-TALK'" Variables: None. Example: SEND_COMMAND TP1,"'^ICM-TALK'" ^ICM-LISTEN See ^ICM section on page 121.
Programming Panel IR Commands These commands are used to transmit and receive IR signals from the panel. Each panel has up to 4 transmit ports specifically defined as IR output ports: AMX 38K AMX 455K User 1 User 2 The ^IRM command allows the command itself to specify the port number. IRM is needed because commands programmed on the panel itself can only be sent to a single port number. The ^IRS command is needed to enable the received AMX 38K or 455k.
Programming SIP Commands The following table lists and describes SIP commands that are generated from the touch panel. SIP Commands ^PHN-AUTOANSWER Provides the state of the auto-answer feature. Syntax: "'^PHN-AUTOANSWER, '" Variable: state = 0 or 1 (off or on) Example: SEND_COMMAND Panel,"'^PHN-AUTOANSWER, 1'" ^PHN-CALL Provides call progress notification for a call. Syntax: "'^PHN-CALL, , '" Variables: status = CONNECTED, DISCONNECTED, TRYING, RINGING, or HOLD.
Programming SIP Commands (Cont.) ^PHN-LINESTATE Indicates the current state of each of the available connections used to manage calls. Syntax: "'^PHN-LINESTATE, , , , ,...'" Variables: connection id = The identifying number of the connection.
Programming The following table lists and describes SIP commands that are sent to the touch panel to manage calls. SIP Commands ^PHN-ANSWER Answers the call. Syntax: "'^PHN-ANSWER, '" Variable: connection id = The identifying number of the connection Example: SEND_COMMAND Panel,"'^PHN-ANSWER, 1'" ^PHN-AUTOANSWER Enables (1) or disables (0) the auto-answer feature on the phone.
Programming SIP Commands (Cont.) ?PHN-LINESTATE Queries the state of each of the connections used by the SIP device. The panel responds with the ^PHN-LINESTATE message. Syntax: "’?PHN-LINESTATE’" Example: SEND_COMMAND Panel,"'?PHN-LINESTATE'" ^PHN-PRIVACY Enables or disables the privacy feature on the phone (do not disturb). Syntax: "’^PHN-PRIVACY, ’" Variable: state = 0 (Disable) or 1 (Enable) Example: SEND_COMMAND Panel,"'^PHN-PRIVACY, 1'" Enables the privacy feature.
Programming SIP Commands (Cont.) ^PHN-SETUP-PASSWORD Sets the user password for the proxy server. Syntax: "’^PHN-SETUP-PASSWORD,’" Variable: password = The password for the user name Example: SEND_COMMAND Panel,"’^PHN-SETUP-PASSWORD,6003’" ^PHN-SETUP-PORT Sets the port number for the proxy server. Syntax: "’^PHN-SETUP-PORT,’" Variable: port = The port for the proxy server Example: SEND_COMMAND Panel,"’^PHN-SETUP-PORT,5060’" ^PHN-SETUP-PROXYADDR Sets the IP address for the proxy server.
Troubleshooting Troubleshooting Overview This section describes the solutions to possible hardware/firmware issues that could arise during the common operation of a Modero touch panel. Troubleshooting Information Symptom Solution My USB drivers has a yellow exclamation point and doesn’t appear to be working. The USB driver was incorrectly installed and should be re-installed: • Power up the panel without the USB cable connected to the panel. • Plug in the USB cable into the G4 panel.
Troubleshooting Troubleshooting Information (Cont.) Symptom Solution My Modero panel can’t obtain a DHCP Address In requesting a DHCP Address, the DHCP Server can take up to a few minutes to provide the address. • Verify that an active Ethernet connection is attached to the rear of the Modero before beginning these procedures. • Select Diagnostics > Network Address from the Main menu and verify the System number.
Troubleshooting Troubleshooting Information (Cont.) Symptom Solution The left border of the graphics has a crawling, dashed line. • On some units at some resolutions, wavy lines may appear across the entire screen. This has been seen on middle resolutions and is referred to as the "Mid Range Fallout" problem. • This is due to the graphics controller settings in the firmware. • Update to the latest v2.XX.XX firmware. Visit the www.amx.
Troubleshooting Troubleshooting Information (Cont.) Symptom Solution After downloading a panel file or firmware to a G4 device, the panel behaves strangely. Symptoms include: • Having to repeat the download. • Inability to make further downloads to the panel. May get "directory" errors, "graphics hierarchy" errors, etc.… indicating problems with the Flash memory. • Panel will not boot, or gets stuck on "AMX" splash screen.
Appendix A - Text Formatting Codes Appendix A - Text Formatting Codes Text Formatting Codes for Bargraphs/Joysticks Text formatting codes for bargraphs provide a mechanism to allow a portion of a bargraphs text to be provided dynamically generated information about the current status of the level (multistate and traditional). These codes would be entered into the text field along with any other text.
Appendix A - Text Formatting Codes Text Area Input Masking Text Area Input Masking can be used to limit the allowed/correct characters that are entered into a text area. For example, in working with a zip code, a user could limit the entry to a max length of only 5 characters but, with input masking, these could be limited to 5 mandatory numerical digits and 4 optional numerical digits. A possible use for this feature is to enter information into form fields.
Appendix A - Text Formatting Codes Input mask ranges These ranges allow a user to specify the minimum and maximum numeric value for a field. Only one range is allowed per field. Using a range implies a numeric entry ONLY. Input Mask Ranges Character Meaning [ Start range ] End range | Range Separator An example from the above table: [0|255] This allows a user to enter a value from 0 to 255.
Appendix A - Text Formatting Codes When data overflows from a numerical field, the overflow value is added to the previous field on the chain if the overflow character was specified. In the above example, if the overflow flag was set, the first example will place the "1" into the previous logical field and the second example will place "12" in the previous logical field.
Appendix A - Text Formatting Codes Special escape sequences The system has only a limited knowledge of URL formats in that it transparently passes the URL information onto the server for translation. A user can then pass any parameters to server side programs such as CGI scripts or active server pages. However, the system will parse the URL looking for special escape codes. When it finds an escape code, it replaces that code with a particular piece of panel, button, or state information.
Appendix A - Text Formatting Codes 138 NXD-500i 5" Wall/Flush Mount Touch Panel with Intercom
Appendix B - Complex Script Support Appendix B - Complex Script Support Overview In many cases, a user needs a touch panel user interface that utilizes a font applicable to the area for which its use is intended, and to accomplish this without needing to resort to images of properly formed text. This includes proper rendering of right-to-left languages such as, but not limited to, Arabic, Hebrew, Thai and Devangari (FIG. 63). Both the NXD-500i and TPDesign4 (v3.
Appendix B - Complex Script Support Some languages, notably Hindi and Tamil, are not supported by coded pages. These languages will display “???” for characters entered via the language bar, even if the selected font supports the language. Text in these languages can still be pasted via the clipboard or via the Alt- method. For more information on TPDesign4 and its complex script support, please refer to the TPDesign4 (v3.0 or higher) Operation Reference Guide, available at www.amx.com.
Appendix B - Complex Script Support NXD-500i 5" Wall/Flush Mount Touch Panel with Intercom 141
7/12 ©2012 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX. AMX reserves the right to alter specifications without notice at any time. It’s Your World - Take Control™ 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 • 469.624.8000 • 469-624-7153 fax • 800.932.6993 technical support • www.amx.
