User's Manual
Table Of Contents
- MVP-9000i 9" Modero® ViewPoint® Touch Panel with Intercom
- Introduction
- Accessories
- Configuring Communication
- Overview
- IR Communication
- Modero Setup and System Settings
- Wireless Settings - Wireless Access Overview
- Configuring Wireless Network Access
- Step 1: Configure the Device’s WiFi Settings
- Step 2: Configure the Card’s Wireless Security Settings
- Step 3: Choose a Master Connection Mode
- Ethernet Over USB
- Using G4 Web Control to Interact with a G4 Panel
- Using the NetLinx Master To Control the G4 Panel
- Setup Pages
- Protected Setup Pages
- Upgrading Firmware
- Programming
- Overview
- Animated Transitions
- Touch Gesture Recognition
- Page Commands
- Programming Numbers
- "^" Button Commands
- Text Effects Names
- Button Query Commands
- Panel Runtime Operations
- Input Commands
- Embedded codes
- Panel Setup Commands
- Dynamic Image Commands
- Intercom Commands
- SIP Commands
- ^PHN- AUTOANSWER
- ^PHN-CALL
- ^PHN-DECLINE
- ^PHN-INCOMING
- ^PHN- LINESTATE
- ^PHN- MSGWAITING
- ^PHN-PRIVACY
- ^PHN-REDIAL
- ^PHN- TRANSFERRED
- ^PHN-ANSWER
- ^PHN- AUTOANSWER
- ?PHN- AUTOANSWER
- ^PHN-CALL
- ^PHN-DTMF
- ^PHN-HANGUP
- ^PHN-HOLD
- ?PHN- LINESTATE
- ^PHN-PRIVACY
- ?PHN-PRIVACY
- ^PHN-REDIAL
- ^PHN- TRANSFER
- ^PHN-SETUP- DOMAIN
- ^PHN-SETUP- ENABLE
- ^PHN-SETUP- PASSWORD
- ^PHN-SETUP- PORT
- ^PHN-SETUP- PROXYADDR
- ^PHN-SETUP- STUNADDR
- ^PHN-SETUP- USERNAME
- Battery Life and Replacement
- Appendix A: Text Formatting
- Appendix B: Wireless Technology
- Appendix C: Troubleshooting
- Overview
- Panel Doesn’t Respond To Touches
- Battery Will Not Hold Or Take A Charge
- MVP-9000i Isn’t Appearing In The Online Tree Tab
- MVP Can’t Obtain a DHCP Address
- My AP Doesn’t Seem To Be Working
- NetLinx Studio Only Detects One Of My Connected Masters
- Can’t Connect To a NetLinx Master
- Only One Modero Panel In My System Shows Up
- Panel Behaves Strangely After Downloading A Panel File Or Firmware
- Overview
Battery Life and Replacement
188
MVP-9000i Modero® Wireless Touch Panel with Intercom
Remove the old battery
1.
Remove the two screws holding the battery case to the back cover. Carefully remove the battery from the
back cover. Please dispose of the battery in a proper fashion as required by municipal or federal
regulations
.
Installing the new battery
1.
Open the plastic bag containing the MVP-BP-9 kit, taking care not to use sharp instruments near the
battery itself.
2. Remove the protective film on the battery case. DO NOT install the battery without removing this film.
3. Attach the new battery to the back cover, either using the two screws used to hold the previous battery to
the cover or with the two replacement screws included with the MVP-BP-9 kit.
Reconnecting the battery to the device
1.
On the back cover, make sure that the battery connector wiring runs to the left.
2. Make sure to seat fully the battery plug to the connector in the device (FIG. 115). If fingers cannot be
used, use a clean, nonconductive stick or probe to seat the connectors.
3. Reattach the back of the device, engaging the ledge at the bottom of the device and using it to swing the
back down into place.
4. Insert the seven screws and replace the rubber feet atop the two upper screws, using the replacement
rubber feet included in the Battery Pack Kit. Replace the bottom label over the three bottom screws, using
the replacement label included in the Battery Pack Kit (FIG. 116).
5. Slide the IR emitter cover back into place over the emitter until it clicks.
Attach the residual voltage discharge adaptor (SAA5966-27-A) to the old battery and
allow any remaining charge to dissipate. Note that the adaptor may become warm to
the touch for up to 24 hours.
When reassembling the device, take especial care not to pinch or squeeze the
connector wiring or the battery. Do not force the back cover onto the device, as this
can damage the device.
FIG. 116 Rear of the MVP-9000i-WH
IR Emitter Cover
Rubber feet
Position of replacement label