User's Manual
Table Of Contents
- MVP-9000i 9" Modero® ViewPoint® Touch Panel with Intercom
- Introduction
- Accessories
- Configuring Communication
- Overview
- IR Communication
- Modero Setup and System Settings
- Wireless Settings - Wireless Access Overview
- Configuring Wireless Network Access
- Step 1: Configure the Device’s WiFi Settings
- Step 2: Configure the Card’s Wireless Security Settings
- Step 3: Choose a Master Connection Mode
- Ethernet Over USB
- Using G4 Web Control to Interact with a G4 Panel
- Using the NetLinx Master To Control the G4 Panel
- Setup Pages
- Protected Setup Pages
- Upgrading Firmware
- Programming
- Overview
- Animated Transitions
- Touch Gesture Recognition
- Page Commands
- Programming Numbers
- "^" Button Commands
- Text Effects Names
- Button Query Commands
- Panel Runtime Operations
- Input Commands
- Embedded codes
- Panel Setup Commands
- Dynamic Image Commands
- Intercom Commands
- SIP Commands
- ^PHN- AUTOANSWER
- ^PHN-CALL
- ^PHN-DECLINE
- ^PHN-INCOMING
- ^PHN- LINESTATE
- ^PHN- MSGWAITING
- ^PHN-PRIVACY
- ^PHN-REDIAL
- ^PHN- TRANSFERRED
- ^PHN-ANSWER
- ^PHN- AUTOANSWER
- ?PHN- AUTOANSWER
- ^PHN-CALL
- ^PHN-DTMF
- ^PHN-HANGUP
- ^PHN-HOLD
- ?PHN- LINESTATE
- ^PHN-PRIVACY
- ?PHN-PRIVACY
- ^PHN-REDIAL
- ^PHN- TRANSFER
- ^PHN-SETUP- DOMAIN
- ^PHN-SETUP- ENABLE
- ^PHN-SETUP- PASSWORD
- ^PHN-SETUP- PORT
- ^PHN-SETUP- PROXYADDR
- ^PHN-SETUP- STUNADDR
- ^PHN-SETUP- USERNAME
- Battery Life and Replacement
- Appendix A: Text Formatting
- Appendix B: Wireless Technology
- Appendix C: Troubleshooting
- Overview
- Panel Doesn’t Respond To Touches
- Battery Will Not Hold Or Take A Charge
- MVP-9000i Isn’t Appearing In The Online Tree Tab
- MVP Can’t Obtain a DHCP Address
- My AP Doesn’t Seem To Be Working
- NetLinx Studio Only Detects One Of My Connected Masters
- Can’t Connect To a NetLinx Master
- Only One Modero Panel In My System Shows Up
- Panel Behaves Strangely After Downloading A Panel File Or Firmware
- Overview
Battery Life and Replacement
186
MVP-9000i Modero® Wireless Touch Panel with Intercom
Battery Replacement
The touch panel's battery is intended to last the life of the device, but in cases where the battery has reached its
effective end of life, it may be replaced.
READ THESE INSTRUCTIONS FIRST!
To minimize the risk of damage to the battery during installation, all replacement batteries come in a protective
metal cover (FIG. 111). This cover cannot be removed from the battery.
Replacing the Battery
Before replacing the battery, download and install the latest firmware for the MVP-9000i. This firmware is
available at www.amx.com.
To remove an old battery and replace it:
1. Remove the battery from its packaging, remove the protective film from the battery, and inspect it for any
damage or distortion. If the battery shows evidence of damage, contact AMX for replacement and proper
disposal information.
2. Place the device face-down on a surface that will not scratch the unit and gently pry up the IR emitter
cover. This will usually be easier to do from the left side of the cover (FIG. 112)
.
3. Once the IR emitter cover is free on one side, carefully lift up away from the device to loosen and remove
the IR emitter cover.
FIG. 111 Lithium-Polymer battery for the MVP-9000i
IMPORTANT: Prior to battery removal, run the device until the battery is completely
discharged. Do NOT discharge the battery before installing the latest MVP-9000i
firmware, available at www.amx.com.
FIG. 112 IR emitter cover removal
Screw slot
Pry up on IR emitter cover
Do NOT use tools of any sort in the screw slot, as this can damage the tab on the
back cover underneath the slot.