User's Manual
Table Of Contents
- MVP-9000i 9" Modero® ViewPoint® Touch Panel with Intercom
- Introduction
- Accessories
- Configuring Communication
- Overview
- IR Communication
- Modero Setup and System Settings
- Wireless Settings - Wireless Access Overview
- Configuring Wireless Network Access
- Step 1: Configure the Device’s WiFi Settings
- Step 2: Configure the Card’s Wireless Security Settings
- Step 3: Choose a Master Connection Mode
- Ethernet Over USB
- Using G4 Web Control to Interact with a G4 Panel
- Using the NetLinx Master To Control the G4 Panel
- Setup Pages
- Protected Setup Pages
- Upgrading Firmware
- Programming
- Overview
- Animated Transitions
- Touch Gesture Recognition
- Page Commands
- Programming Numbers
- "^" Button Commands
- Text Effects Names
- Button Query Commands
- Panel Runtime Operations
- Input Commands
- Embedded codes
- Panel Setup Commands
- Dynamic Image Commands
- Intercom Commands
- SIP Commands
- ^PHN- AUTOANSWER
- ^PHN-CALL
- ^PHN-DECLINE
- ^PHN-INCOMING
- ^PHN- LINESTATE
- ^PHN- MSGWAITING
- ^PHN-PRIVACY
- ^PHN-REDIAL
- ^PHN- TRANSFERRED
- ^PHN-ANSWER
- ^PHN- AUTOANSWER
- ?PHN- AUTOANSWER
- ^PHN-CALL
- ^PHN-DTMF
- ^PHN-HANGUP
- ^PHN-HOLD
- ?PHN- LINESTATE
- ^PHN-PRIVACY
- ?PHN-PRIVACY
- ^PHN-REDIAL
- ^PHN- TRANSFER
- ^PHN-SETUP- DOMAIN
- ^PHN-SETUP- ENABLE
- ^PHN-SETUP- PASSWORD
- ^PHN-SETUP- PORT
- ^PHN-SETUP- PROXYADDR
- ^PHN-SETUP- STUNADDR
- ^PHN-SETUP- USERNAME
- Battery Life and Replacement
- Appendix A: Text Formatting
- Appendix B: Wireless Technology
- Appendix C: Troubleshooting
- Overview
- Panel Doesn’t Respond To Touches
- Battery Will Not Hold Or Take A Charge
- MVP-9000i Isn’t Appearing In The Online Tree Tab
- MVP Can’t Obtain a DHCP Address
- My AP Doesn’t Seem To Be Working
- NetLinx Studio Only Detects One Of My Connected Masters
- Can’t Connect To a NetLinx Master
- Only One Modero Panel In My System Shows Up
- Panel Behaves Strangely After Downloading A Panel File Or Firmware
- Overview
Battery Life and Replacement
185
MVP-9000i Modero® Wireless Touch Panel with Intercom
Power Management
Since the MVP-9000i is a battery-powered handheld device, power management is a necessary concern. Under
active use, the charge on the integral Lithium-Polymer battery can last for as long as five days. However, to
maximize usability and minimize the chances of the device becoming completely discharged at a critical
moment, the MVP-9000i should be kept in its charging cradle or wall station when not in use.
The MVP-9000i operates on four distinct power modes:
On - This is the normal power mode of the panel during operation. In this mode, all necessary
modules are powered up and their respective clocks are being driven appropriately. The device
remains online with the NetLinx Master and continues to appear in the online tree of NetLinx
Studio.
Sleep - This mode of operation can be selected through the Setup Pages and only controls the
backlight. In this case, the unit remains on all the time, and only the backlight will be turned off
after the user-selectable time of inactivity has elapsed. The device remains online with the NetLinx
Master and continues to be shown in the online tree of NetLinx Studio. The unit shall transfer to the
Awake mode after it detects a touch on the touchscreen or capacitive touch buttons. This mode uses
50 percent of the power required for the Awake mode.
Standby - In this mode, power to all components other than the touch screen is turned off after the
user selectable time of inactivity has elapsed. Device will turn back on by touching the screen. Re-
acquiring an AP connection may require up to 25 seconds.
Shutdown - The system enters this mode after a user selectable amount of inactivity time has
elapsed or if the battery level falls below 5 percent of its full charge. This is the absolute lowest
mode of operation, during which power to all peripherals and components is turned off. It is not
online with the NetLinx Master and will not appear in NetLinx Studio. The system remains in this
mode until the screen is touched, or external power is applied.
Proper Battery Maintenance
To insure maximum performance and reliability of the MVP-9000i, please insure that a full charge is
performed every 3 months if not used regularly. If a battery is left uncharged beyond this time frame, it may
result in premature battery lifespan degradation and will require replacement.
Standby Mode cannot be entered if a USB device or microSD card is connected to
the MVP-9000i.
In Standby Mode, the panel will go offline.
Power Modes for the MVP-9000i
Mode Power Use Time Available (With Full Battery Charge)
On 100% 5 hours
Sleep 50% 10 hours
Standby 15% 72 hours
Shutdown Less than 1% Up to one month