User's Manual
Table Of Contents
- MVP-9000i9" Modero® ViewPoint®Touch Panel with Intercom
- Introduction
- Accessories
- Configuring Communication
- Overview
- IR Communication
- Modero Setup and System Settings
- Wireless Settings - Wireless Access Overview
- Configuring Wireless Network Access
- Step 1: Configure the Device’s WiFi Settings
- Step 2: Configure the Card’s Wireless Security Settings
- Step 3: Choose a Master Connection Mode
- Ethernet Over USB
- Using G4 Web Control to Interact with a G4 Panel
- Using the NetLinx Master To Control the G4 Panel
- Setup Pages
- Protected Setup Pages
- Upgrading Firmware
- Programming
- Overview
- Animated Transitions
- Touch Gesture Recognition
- Page Commands
- Programming Numbers
- "^" Button Commands
- Text Effects Names
- Button Query Commands
- Panel Runtime Operations
- Input Commands
- Embedded codes
- Panel Setup Commands
- Dynamic Image Commands
- Intercom Commands
- SIP Commands
- ^PHN- AUTOANSWER
- ^PHN-CALL
- ^PHN-INCOMING
- ^PHN- LINESTATE
- ^PHN- MSGWAITING
- ^PHN-PRIVACY
- ^PHN-REDIAL
- ^PHN- TRANSFERRED
- ^PHN-ANSWER
- ^PHN- AUTOANSWER
- ?PHN- AUTOANSWER
- ^PHN-CALL
- ^PHN-DTMF
- ^PHN-HANGUP
- ^PHN-HOLD
- ?PHN- LINESTATE
- ^PHN-PRIVACY
- ?PHN-PRIVACY
- ^PHN-REDIAL
- ^PHN- TRANSFER
- ^PHN-SETUP- DOMAIN
- ^PHN-SETUP- ENABLE
- ^PHN-SETUP- PASSWORD
- ^PHN-SETUP- PORT
- ^PHN-SETUP- PROXYADDR
- ^PHN-SETUP- STUNADDR
- ^PHN-SETUP- USERNAME
- Battery Life and Replacement
- Appendix A: Text Formatting
- Appendix B: Wireless Technology
- Appendix C: Troubleshooting
- Overview
- Panel Doesn’t Respond To Touches
- Battery Will Not Hold Or Take A Charge
- MVP-9000i Isn’t Appearing In The Online Tree Tab
- MVP Can’t Obtain a DHCP Address
- My WAP Doesn’t Seem To Be Working
- NetLinx Studio Only Detects One Of My Connected Masters
- Can’t Connect To a NetLinx Master
- Only One Modero Panel In My System Shows Up
- Panel Behaves Strangely After Downloading A Panel File Or Firmware
- Overview
Setup Pages
49
MVP-9000i Modero® Wireless Touch Panel with Intercom
Audio Page
The Audio page allows adjustment of volume levels and panel sounds settings (FIG. 49).
Features on this page include:
FIG. 49 Audio pages
Audio Page
Back: Saves all changes and returns to the previous page.
Connection Status icon: The icon in the upper-right corner of each Setup page provides a constant
visual indication of current connection status.
Note: a Lock appears on the icon if the panel is connected to a secured NetLinx
Master.
Button Sounds: • Activating the Hit On button plays a default sound when you touch an active
button. Touch the field a second time to switch the button to Hit Off, which
disables the sound.
• Activating Miss On button plays a default sound when you touch a non-active
button or any area outside of the active button. Touch the field a second time
to switch the button to Miss Off, which disables the sound.
•The Test button plays a test WAV/MP3 file over the panel’s internal speakers.
Intercom
Mic Level: Adjusts the volume level on the intercom’s microphone:
• Use the Up/Down buttons to adjust the microphone level (range = 0 - 100%).
Press the Mute On button to mute the microphone and press it again
(switching the button to Mute Off) to enable it.
Volume: Adjusts the volume level on the touch panel’s speaker:
• Use the Up/Down buttons to adjust the speaker level (range = 0 - 100%).
Press the Mute On button to mute the speaker and press it again (switching
the button to Mute Off) to enable it.
Master Volume: This section allows you to alter the current master volume level:
• Use the Up/Down buttons to adjust the volume level in one-percent
increments (range = 0 - 100%).
• The Master Volume readout indicates the current volume level. Press the Up/
Down buttons to adjust the volume level in one-percent increments (range =
0 - 100%).
• The Mute On button toggles the Mute feature. Press it again to switch it to
Mute Off.