User's Manual
Table Of Contents
- MVP-9000i9" Modero® ViewPoint®Touch Panel with Intercom
- Introduction
- Accessories
- Configuring Communication
- Overview
- IR Communication
- Modero Setup and System Settings
- Wireless Settings - Wireless Access Overview
- Configuring Wireless Network Access
- Step 1: Configure the Device’s WiFi Settings
- Step 2: Configure the Card’s Wireless Security Settings
- Step 3: Choose a Master Connection Mode
- Ethernet Over USB
- Using G4 Web Control to Interact with a G4 Panel
- Using the NetLinx Master To Control the G4 Panel
- Setup Pages
- Protected Setup Pages
- Upgrading Firmware
- Programming
- Overview
- Animated Transitions
- Touch Gesture Recognition
- Page Commands
- Programming Numbers
- "^" Button Commands
- Text Effects Names
- Button Query Commands
- Panel Runtime Operations
- Input Commands
- Embedded codes
- Panel Setup Commands
- Dynamic Image Commands
- Intercom Commands
- SIP Commands
- ^PHN- AUTOANSWER
- ^PHN-CALL
- ^PHN-INCOMING
- ^PHN- LINESTATE
- ^PHN- MSGWAITING
- ^PHN-PRIVACY
- ^PHN-REDIAL
- ^PHN- TRANSFERRED
- ^PHN-ANSWER
- ^PHN- AUTOANSWER
- ?PHN- AUTOANSWER
- ^PHN-CALL
- ^PHN-DTMF
- ^PHN-HANGUP
- ^PHN-HOLD
- ?PHN- LINESTATE
- ^PHN-PRIVACY
- ?PHN-PRIVACY
- ^PHN-REDIAL
- ^PHN- TRANSFER
- ^PHN-SETUP- DOMAIN
- ^PHN-SETUP- ENABLE
- ^PHN-SETUP- PASSWORD
- ^PHN-SETUP- PORT
- ^PHN-SETUP- PROXYADDR
- ^PHN-SETUP- STUNADDR
- ^PHN-SETUP- USERNAME
- Battery Life and Replacement
- Appendix A: Text Formatting
- Appendix B: Wireless Technology
- Appendix C: Troubleshooting
- Overview
- Panel Doesn’t Respond To Touches
- Battery Will Not Hold Or Take A Charge
- MVP-9000i Isn’t Appearing In The Online Tree Tab
- MVP Can’t Obtain a DHCP Address
- My WAP Doesn’t Seem To Be Working
- NetLinx Studio Only Detects One Of My Connected Masters
- Can’t Connect To a NetLinx Master
- Only One Modero Panel In My System Shows Up
- Panel Behaves Strangely After Downloading A Panel File Or Firmware
- Overview
Accessories
19
MVP-9000i Modero® Wireless Touch Panel with Intercom
6. Cut out the opening for the MVP-WDS-9 where the wall has been placed over the Rough-In Box. Cutting
out the surface slightly smaller than what is outlined in the installation drawings, so that you can make
any necessary cutout adjustments, is very highly recommended.
Other MVP-WDS-9 installations
The Wall-Mounted Docking Station is designed to be installed in various different locations, such as into the
face of a wooden podium or the top of a table. Depending upon the ability to wire it to a power source, Wall-
Mounted Docking Stations may be installed on vertical or horizontal surfaces composed of such materials as
wood, brick, and glass.
Installing a Wall-Mounted Docking Station into a solid wall thicker than a standard thickness of sheetrock is
possible, but requires special preparation. If installing into a solid wall of concrete or rock, a recess must be
chiselled or cut out to match the size of the device. The box is sized 8.375 inches (21.27cm) long and 5.75
inches (14.60cm) high, so the hole should be at least 1/4” (0.64cm) smaller in these dimensions. To facilitate
the full range of movement of the device’s components, the recess must be at least 2.69 inches (6.83cm) deep.
Ensure that the power cable has been installed in the wall and is accessible by the
installer before chiseling out the recess.
Instead of using the lockdown wings to secure the Plastic Back Box, standard
concrete screws may be inserted through the screw holes after removing the
lockdown wings.
However, drill the concrete screw holes into the wall before setting the screws into the
box, as excessive torque applied to the screws will damage the box.
To avoid this, the box may be installed with adhesive. Test an unobtrusive spot on the
back of the box with a sample of the adhesive to check for any adverse reactions
before installing the device.