User's Manual
Table Of Contents
- MVP-9000i9" Modero® ViewPoint®Touch Panel with Intercom
- Introduction
- Accessories
- Configuring Communication
- Overview
- IR Communication
- Modero Setup and System Settings
- Wireless Settings - Wireless Access Overview
- Configuring Wireless Network Access
- Step 1: Configure the Device’s WiFi Settings
- Step 2: Configure the Card’s Wireless Security Settings
- Step 3: Choose a Master Connection Mode
- Ethernet Over USB
- Using G4 Web Control to Interact with a G4 Panel
- Using the NetLinx Master To Control the G4 Panel
- Setup Pages
- Protected Setup Pages
- Upgrading Firmware
- Programming
- Overview
- Animated Transitions
- Touch Gesture Recognition
- Page Commands
- Programming Numbers
- "^" Button Commands
- Text Effects Names
- Button Query Commands
- Panel Runtime Operations
- Input Commands
- Embedded codes
- Panel Setup Commands
- Dynamic Image Commands
- Intercom Commands
- SIP Commands
- ^PHN- AUTOANSWER
- ^PHN-CALL
- ^PHN-INCOMING
- ^PHN- LINESTATE
- ^PHN- MSGWAITING
- ^PHN-PRIVACY
- ^PHN-REDIAL
- ^PHN- TRANSFERRED
- ^PHN-ANSWER
- ^PHN- AUTOANSWER
- ?PHN- AUTOANSWER
- ^PHN-CALL
- ^PHN-DTMF
- ^PHN-HANGUP
- ^PHN-HOLD
- ?PHN- LINESTATE
- ^PHN-PRIVACY
- ?PHN-PRIVACY
- ^PHN-REDIAL
- ^PHN- TRANSFER
- ^PHN-SETUP- DOMAIN
- ^PHN-SETUP- ENABLE
- ^PHN-SETUP- PASSWORD
- ^PHN-SETUP- PORT
- ^PHN-SETUP- PROXYADDR
- ^PHN-SETUP- STUNADDR
- ^PHN-SETUP- USERNAME
- Battery Life and Replacement
- Appendix A: Text Formatting
- Appendix B: Wireless Technology
- Appendix C: Troubleshooting
- Overview
- Panel Doesn’t Respond To Touches
- Battery Will Not Hold Or Take A Charge
- MVP-9000i Isn’t Appearing In The Online Tree Tab
- MVP Can’t Obtain a DHCP Address
- My WAP Doesn’t Seem To Be Working
- NetLinx Studio Only Detects One Of My Connected Masters
- Can’t Connect To a NetLinx Master
- Only One Modero Panel In My System Shows Up
- Panel Behaves Strangely After Downloading A Panel File Or Firmware
- Overview
Accessories
11
MVP-9000i Modero® Wireless Touch Panel with Intercom
Recharging
To recharge the MVP-9000i, slide the device into the Table Docking Station cradle bottom-first and make sure
the device is fully seated in the Docking Station. The charger pins in the bottom of the cradle (FIG. 7) must be
in contact with the connector on the bottom of the MVP-9000i for it to start recharging. The MVP panel will
stop recharging automatically once the battery has achieved its maximum charge.
Using the USB ports
The MVP-TDS-9 has two USB ports on the left of the device behind the Docking Station cradle (FIG. 7).
These ports may be used for transferring files to the MVP-9000i, as well as ports for USB-powered
accessories.
Cleaning the MVP-TDS-9
You should clean the MVP-TDS-9 Table Docking Station after each day’s use to maintain the device’s
appearance. Always use a clean cotton cloth and a spray bottle containing water or a non-ammonia-based
cleaner, as alcohol-based cleaners can damage the device. Do not directly spray the device: instead, spray the
cloth to prevent moisture from collecting on the charger pins. Do NOT use an abrasive of any type to clean the
Table Docking Station, as this may permanently damage or remove the device’s finish.
FIG. 7 MVP-TDS-9-GW Table Docking Station - Rear
Charger pins
Docking Station cradle
Locking groove
USB ports (2)