User's Manual
Table Of Contents
- MVP-9000i9" Modero® ViewPoint®Touch Panel with Intercom
- Introduction
- Accessories
- Configuring Communication
- Overview
- IR Communication
- Modero Setup and System Settings
- Wireless Settings - Wireless Access Overview
- Configuring Wireless Network Access
- Step 1: Configure the Device’s WiFi Settings
- Step 2: Configure the Card’s Wireless Security Settings
- Step 3: Choose a Master Connection Mode
- Ethernet Over USB
- Using G4 Web Control to Interact with a G4 Panel
- Using the NetLinx Master To Control the G4 Panel
- Setup Pages
- Protected Setup Pages
- Upgrading Firmware
- Programming
- Overview
- Animated Transitions
- Touch Gesture Recognition
- Page Commands
- Programming Numbers
- "^" Button Commands
- Text Effects Names
- Button Query Commands
- Panel Runtime Operations
- Input Commands
- Embedded codes
- Panel Setup Commands
- Dynamic Image Commands
- Intercom Commands
- SIP Commands
- ^PHN- AUTOANSWER
- ^PHN-CALL
- ^PHN-INCOMING
- ^PHN- LINESTATE
- ^PHN- MSGWAITING
- ^PHN-PRIVACY
- ^PHN-REDIAL
- ^PHN- TRANSFERRED
- ^PHN-ANSWER
- ^PHN- AUTOANSWER
- ?PHN- AUTOANSWER
- ^PHN-CALL
- ^PHN-DTMF
- ^PHN-HANGUP
- ^PHN-HOLD
- ?PHN- LINESTATE
- ^PHN-PRIVACY
- ?PHN-PRIVACY
- ^PHN-REDIAL
- ^PHN- TRANSFER
- ^PHN-SETUP- DOMAIN
- ^PHN-SETUP- ENABLE
- ^PHN-SETUP- PASSWORD
- ^PHN-SETUP- PORT
- ^PHN-SETUP- PROXYADDR
- ^PHN-SETUP- STUNADDR
- ^PHN-SETUP- USERNAME
- Battery Life and Replacement
- Appendix A: Text Formatting
- Appendix B: Wireless Technology
- Appendix C: Troubleshooting
- Overview
- Panel Doesn’t Respond To Touches
- Battery Will Not Hold Or Take A Charge
- MVP-9000i Isn’t Appearing In The Online Tree Tab
- MVP Can’t Obtain a DHCP Address
- My WAP Doesn’t Seem To Be Working
- NetLinx Studio Only Detects One Of My Connected Masters
- Can’t Connect To a NetLinx Master
- Only One Modero Panel In My System Shows Up
- Panel Behaves Strangely After Downloading A Panel File Or Firmware
- Overview
Programming
163
MVP-9000i Modero® Wireless Touch Panel with Intercom
The following table lists and describes SIP commands that are sent to the touch panel to manage calls.
SIP Commands (Cont.)
^PHN-PRIVACY
Indicates the state
of the privacy fea-
ture.
Syntax:
"'^PHN-PRIVACY, <state>'"
Variable:
state = 0 (Disable) or 1 (Enable)
new message count = The number of new messages.
old message count = The number of old messages.
new urgent message count = The number of new messages marked urgent.
old urgent message count = The number of old messages marked urgent.
Example:
SEND_COMMAND Panel,"'^PHN-PRIVACY, 0’"
^PHN-REDIAL
Indicates the
panel is redialing
the number.
Syntax:
"'^PHN-REDIAL, <number>'"
Variable:
number = The phone number to dial.
Example:
SEND_COMMAND Panel,"'^PHN-REDIAL, 2125551000’"
^PHN-
TRANSFERRED
Indicates a call
has been trans-
ferred.
Syntax:
"'^PHN-TRANSFERRED'"
Example:
SEND_COMMAND Panel,"'^PHN-TRANSFERRED’"
SIP Commands
^PHN-ANSWER
Answers the call.
Syntax:
"'^PHN-ANSWER, <connection id>'"
Variable:
connection id = The identifying number of the connection
Example:
SEND_COMMAND Panel,"'^PHN-ANSWER, 1'"
^PHN-
AUTOANSWER
Enables or
disables the auto-
answer
feature of the
phone.
Enables (1) or disables (0) the auto-answer feature on the phone.
Syntax:
"’^PHN-AUTOANSWER, <state>’"
Variable:
state = 0 (Disable) or 1 (Enable)
Example:
SEND_COMMAND Panel,"'^PHN-AUTOANSWER, 1'"
Enables the auto-answer feature.
?PHN-
AUTOANSWER
Queries the state
of the auto-
answer feature.
The panel responds with the ^PHN-AUTOANSWER, <state> message.
Syntax:
"’?PHN-AUTOANSWER’"
Example:
SEND_COMMAND Panel,"'?PHN-AUTOANSWER'"
^PHN-CALL
Calls the
provided number.
Syntax:
"’^PHN-CALL, <number>’"
Variable:
number = The provided phone number
Example:
SEND_COMMAND Panel,"'^PHN-CALL, 2125551000'"