Specifications

Quick Start Guide
MVP-8400 8.4" Modero ViewPoint Touch Panel
Overview
The AMX MVP-8400 panel (FG5965-05) uses an internal wireless compact flash card
to communicate with a NetLinx Master via an off-the-shelf 802.11b/g Wireless Access
Point. The MVP-8400 units utilizes a 8.4" Color Active LCD to display a 800 x 600 pixel
image using over 256 K colors, and features programmable firmware that can be
upgraded via either the wireless card or the mini-USB port.
The MVP-8400 also features nine programmable external pushbuttons and two sets of
display LEDs. These panels are configured to operate on a standard 802.11b/g
wireless network. On the 4 available IR channels, this panel utilizes both AMX IR
frequencies (38 KHz or 455 KHz) and 2 additional user-defined IR libraries.
For detailed installation, configuration, programming, file transfer, and operating
instructions refer to the MVP-7500/8400 Modero ViewPoint Touch Panels operation/
reference guide, available on-line at www.amx.com.
Specifications
Connections and Wiring
The PS4.4 Power Supply (with barrel connector) provides power to the MVP-8400
either directly (via the power connector located on the lower right-side of the panel) or
indirectly (by routing incoming power through the Docking Station’s MVP Interface
Connector).
• Once the MVP is connected to a docking station; charging priority is first given to
any MVP-BP battery packs found within the MVP-8400 and then to any other
batteries inserted into the docking station’s battery charging compartments.
WARNING: Although firmware upgrades can be done over wireless Ethernet; it is
strongly recommended that firmware KIT files be transferred over a direct USB
connection and only when the panel is connected to a power supply. If battery power
or wireless connection fails during a firmware upgrade, the panel flash file system may
become corrupted.
Setup Pages
The panel is equipped with setup pages that allow you to set and configure various
features on the panel. Consult the MVP-7500/8400 Modero ViewPoint Touch Panels
Operation/Reference guide for detailed information on the Setup pages.
Accessing The Protected Setup Page
1. Press down and hold both the bottom, left pushbutton and down on the direc-
tional pad (indicated in FIG. 1) simultaneously for 3-5 seconds. This opens the
Setup page.
2. Press Protected Setup button on the Setup page. This opens a keypad for
password entry.
3. Enter the panel password into the keypad (default is 1988) and select Done to
access the Protected Setup page.
Setting the Panel’s Device Number
In the Protected Setup page:
1. Press the Device Number field to open the Device Number keypad.
Enter a unique Device Number assignment for the panel, and press Done
to return to the Protected Setup page.
2. Press Reboot to reboot the panel, and apply the new Device Number.
FIG. 1
MVP-8400 Touch Panel component locations
MVP-8400 (FG5965-05) Specifications
Dimensions (HWD): 7.17" x 10.47" x 1.34" (18.20 cm x 26.60 cm x 3.40 cm)
Power Requirement
(without charging):
Panel with batteries fully charged or with no batteries:
• Constant current draw: 1.2 A @ 12 VDC
• Startup current draw: 1.8 A @ 12 VDC
• If panel is mounted onto a TDS or WDS, add 0.1 A to the
above figures.
Power Requirement
(while charging):
Panel while charging batteries:
• Constant current draw: 3.2 A @ 12 VDC
• Startup current draw: 3.8 A @ 12 VDC
• If panel is mounted onto a TDS or WDS, add 0.1 A to the
above figures.
Minimum power
supply required:
PS4.4 Power Supply (FG423-45)
- All MVP models are shipped with this power supply.
Power Modes: • ON: Panel is fully functional.
• STANDBY: Panel uses low power, the LCD/backlight is
shutdown, LEDs still function. Panel resumes the ON
mode in ~ 1 second.
• OFF: On-board programs not running, touch screen still
powered, LED not functional. Panel resumes the ON
mode in ~ 30 seconds.
Certifications: • FCC Part 15 Class B and CE
Battery Duration: • Eight hours of normal use (25% On state, 25% Standby,
and 50% Off).
• Four hours of continuous use (continuous On state).
The MVP-8400 ships with two MVP-BP batteries. You must
use both batteries to obtain the duration times given above.
Memory: • 64 MB SDRAM
• 64 MB Compact Flash (upgradable to 1 GB) - factory
programmed
Weight: • Panel (no batteries): 1.85 lbs (0.84 kg)
• Panel with one battery: 2.25 lbs (1.02 kg)
Docking station interface connector
Power connector
Directional pad w/center select button
Mini-USB
Stylus
Pushbuttons (4)
C
C
connector
Speaker Speaker
MVP-8400 Specifications (Cont.)
Screen Properties: • Screen resolution: 800 x 600 pixels (HV) @ 60 Hz frame
frequency
• Aspect ratio: 4 x 3
• Brightness (luminance): 180 cd/m2
• Channel transparency: 8-bit Alpha blending
• Contrast ratio: 350:1
• Display colors: 256K colors (18-bit color depth)
• Dot/pixel pitch: 0.21 mm
• Panel type: TFT Color Active-Matrix
Viewing Angle: • Vertical: + 60° (up from center) and - 40° (down from
center)
Operating/Storage
Environments:
• Operating Temperature: 0° C (32° F) to 40° C (104° F)
• Operating Humidity: 20% - 85% RH
• Storage Temperature: -20° C (-4° F) to 60° C (140° F)
• Storage Humidity: 5% - 85% RH
Included
Accessories:
• Wireless Interface Compact Flash card (CF Type 1)
(pre-installed into MVP)
• PS4.4 Power Supply (FG423-44)
• Stylus (pre-installed onto the left side of the unit)
• Two MVP-BP Power Packs (FG5965-20)
Other AMX
Equipment:
• CB-MVPWDS Conduit Box (FG037-10)
• CC-USB Type A to mini-B programming cable (FG10-5965)
• MVP-BP battery (FG5965-20)
• MVP-KS Kickstand (FG5965-12)
• MVP-STYLUS three pack (FG5965-30)
• MVP-TDS Table Top Docking Station (FG5965-10)
• MVP-WDS Wall Docking Station - Black (FG5965-11)
• MVP-WDS Wall Docking Station - Silver (FG5965-21)
• MVP-WDS-SK Silver Conversion Kit (FG5965-22)
• Upgrade Compact Flash (pre-programmed with firmware):
NXA-84CF128M 128 MB compact flash card (FG2116-50)
NXA-84CF256M 256 MB compact flash card (FG2116-51)
NXA-84CF512M 512 MB compact flash card (FG2116-52)
NXA-84CF1GB 1 GB compact flash card (FG2116-53)