Specifications
Overview
3
Enova DVX-2100HD 6x2 All-in-One Presentation Switcher Operation/Reference Guide
DVX-2100HD Specifications (Cont.)
Rear Panel Components:
RS-232/422/485
(PORT 1-3):
RS-232/422/485 Ports 1-3 provide serial control via DB9 (male) connectors:
• XON/XOFF (transmit on/transmit off)
• CTS/RTS (clear to send/ready to send)
• 300-115,200 baud
RELAYS (PORT 4): Port 4 provides Relay control via 8-pin 3.5 mm captive-wire connector.
• 4-channel single-pole single-throw relay ports
• Each relay is independently controlled
• Supports up to 4 independent external relay devices
• Channel range = 1-4
• Each relay can switch up to 24 VDC or 28 VAC @ 1 A
• One 8-pin 3.5 mm mini-Phoenix (female) connectors provide relay termination
IR/SERIAL (PORTS
5-8):
Ports 5-8 provide IR/Serial control via 2-pin 3.5 mm captive-wire connectors.
• Supports high-frequency carriers of up to 1.142 MHz.
• 4 IR/Serial data signals can be generated simultaneously.
I/O (PORT 9): Port 9 provides 4-channel binary I/O port for contact closure with each input being
capable of voltage sensing.
Input format is software selectable with interactive power sensing for IR ports.
AUDIO INPUTS: 4 3.5mm 5-pin captive-wire connectors receive up to four balanced/unbalanced line
level audio inputs.
• Nominal input level: +4 dBu (1.228 Vrms) balanced or -10 dBV (0.3162 Vrms)
unbalanced
• Maximum input level: 2 Vrms
• Input impedance: >12k ohms unbalanced, >12k ohms balanced, DC coupled
MIC INPUTS: 2 3.5mm 3-pin captive-wire connectors receive up to 2 mono microphones (balanced
or unbalanced audio and switchable Phantom Power).
AUDIO OUTPUTS: • LINE: 1 3.5mm 5-pin captive-wire connector provides for fixed or variable,
balanced or unbalanced, mono or stereo line level audio output.
• AMP: 4-position captive wire connector provides amplified audio output with
volume control (DVX-2100HD-SP only).
• AMP: Two 2-position captive wire connector provides 70V or 100V mono amplified
audio output (DVX-2100HD-T only).
VIDEO INPUTS (1-4): 4 DVI-I input connectors provide multi-format video inputs for up to four video
sources.
Each VIDEO INPUT connector supports RGBHV, S-video, composite video,
component video, and DVI input. See the Available Pixel Display and Refresh
Rates section on page 95 for information on supported video formats and
resolutions.
UDM INPUTS (5-6): 2 RJ-45 inputs receive audio and video from up to two UDM Multi-Format Distribution
Hubs or UPX wallplates.
The DVX-2100HD is compatible with all UDM Multi-Format Distribution Hubs and
UPX wallplates.
VIDEO OUTPUTS
(1-2):
• 2 DVI-I Output connectors each provide simultaneous digital DVI and analog
RGBHV video output (FG1905-04 and -05 only). You can view both Digital and
Analog signals at the same time by using a DVI-I to DVI-D/HD15 splitter. See the
VIDEO OUTPUTS (1-2) and UDM OUTPUTsection on page 28 for details.
• 1 DVI-I digital and analog Output connector and RGB analog only output connector
(FG1905-01 and -02 only). See the Power Connector/Switch/Fuse section on
page 31 for details.
UDM OUTPUT (1): 1 RJ-45 connector allows the DVX-2100HD to connect to a UDM Multi-Format
Receiver. The Video on this output is identical to DVI output 1. You can configure the
audio to follow either the AMP or Line outputs.