Instruction manual

Enova 21xx All-in-One Presentation Switchers
9
Enova DVX-315xHD & DVX-215xHD All-in-One Presentation Switchers - Instruction Manual
DVX-2150HD/2155HD/2110HD Specifications (Cont.)
Rear Panel Components: (Cont.)
HDMI INPUTS: • 4 HDMI inputs (3-6) receive digital audio and video from up to four video sources.
(DVX-2150HD only)
• 2 HDMI inputs (3-4) receive digital audio and video from up to two video sources.
(DVX-2155HD and DVX-2110HD only)
All HDMI inputs are HDCP compatible. See the HDMI INPUTS section on page 26 for more
information.
DXLINK INPUTS: 2 RJ-45 inputs (5-6) provide support for digital video, audio, Ethernet, bi-directional control and
power over Category Cable from any DXLink transmitter (DVX-2155HD and DVX-2110HD
only). See the Supported Video Settings section on page 28 for more information.
VIDEO OUTPUTS: • 2 HDMI Output connectors (1-2) each provide HDMI digital audio and video output.
• 1 DXLink RJ-45 output (3) provides digital video, audio, Ethernet, and bi-directional control
over Twisted Pair Cable to DXLink Receivers. (On the DVX-2110HD, the DXLink output
mirrors HDMI port 1.)
See the VIDEO OUTPUTS section on page 28 for more information and important cable
recommendations.
CONFIG DIP Switch: 8-position Master configuration DIP switch allows setting the Serial Programming port baud
rate and on-board Master execution mode (PRD or normal). See the
CONFIG DIP Switch section on page 34 for more information.
PROGRAM Port: DB9 connector (male) connects to a DB9 serial port on a PC, for serial communication. This
connection is used to configure system settings.
Note: This port is not recommended for firmware updates or large file transfers. Any large data-
intensive operations are better handled via Ethernet.
See the PROGRAM Port section on page 35 for more information.
ID Pushbutton: Black ID pushbutton sets the NetLinx Device ID assignments of the Internal Control Device.
See the ID Pushbutton section on page 35 for more information.
LAN Port: RJ-45 connector provides TCP/IP communication. See the LAN (RJ-45) section on page 35 for
more information.
AxLink Port: 1 3.5 mm 4-pin captive-wire connector provides data and power to external control devices.
The AxLink LED (green) indicates the state of the AxLink port. The AxLink port can be used to
supply power to downstream AxLink-compatible devices as long as the maximum current draw
is less than 1 Amp.
Note: The AxLink port provides only limited power to connected AxLink devices. It is
recommended to use an alternate power source when connecting AxLink devices to the DVX.
Note: When using the DVX with the NXA-PDU-1508-8 power distribution unit, do NOT connect
+12V power from any of the NXA-PDU's AxLink ports to the AxLink power pin.
See the AxLink Port and LED (4-pin captive-wire) section on page 36 for more information.
Power Connector: IEC Power cord connector: 100-240V AC, 47-63Hz
Operating Environment: • Storage temperature: -10º C to 70º C (14º F to 158º F)
• Operating Temperature: 0º C to 40º C (32º F to 104º F)
• Operating Relative Humidity: 5% to 85% non-condensing
Supported Video
Resolutions:
HD resolutions up to 1080p and RGB resolutions up to 1920x1200@60Hz. Higher resolutions
are supported in pass-through mode. See the Available Pixel Display and Refresh
Rates section on page 121 for a complete listing of all supported video resolutions.
Dimensions (HWD): 5 3/16" x 17" x 14" (13.2 cm x 43.2 cm x 35.6 cm)
Weight: • DVX-2150HD/DVX-2155HD: 18.3 lbs (8.31 kg)
• DVX-2110HD-SP: 17 lbs (7.7 kg)
• DVX-2110HD-T: 21 lbs (9.5 kg)
Enclosure: Metal with black matte finish