Product Specification Product Specification WN7511E 2-LF-MT IEEE 802.11n USB2.0 Adapter v.
Product Specification Table of Contents Chapter 1 Introduction ________________________________________________________ 4 1. Introduction ________________________________________________________ 4 1.1 Product Features____________________________________________________ 4 1.2 Applications _______________________________________________________ 4 Chapter 2 Hardware _______________________________________________________ 5 2.1 General Overview __________________________________________________ 5 2.
Product Specification Revision History Edition # Reason for revision Issue date Written by V 0.1 ♦ Initial Document 2009/0918 Troy Chen V 0.2 ♦ Update PCB outline & Antenna cable 2009/12/11 Andre Lin V 0.3 ♦ Update photo for Chapter 2.6 2010/02/10 Andre Lin 2010/03/09 Andre Lin V 0.4 Edited photo for Chapter 2.
Product Specification Chapter 1 Introduction 1. Introduction WN7511E is a wireless 1x1 802.11n USB Adapter which enables wireless networking systems to attain data communication speeds up to 150 megabits-per-second (Mbps), while remaining backward compatible to the existing installed base of Wi-Fi systems worldwide. It supports operation to the IEEE 802.11b and IEEE 802.11g ,and draft IEEE 802.11n standards. WN7511E will enable a next generation of high-data-rate platforms for operation in the 2.
Product Specification Chapter 2 2.1 Hardware General Overview ♦ USB 2.0 Interface and 802.11 n chipset-on-board design. ♦ 1 antenna connector 2.2 Hardware Architecture BRCM 4319 2.3 Main Chipset Information BRCM 4319: Dual-band 2.4 GHz 802.11 b, g, and n.
Product Specification 2.
Product Specification 2.
Product Specification M47 8
Product Specification M55 9
Product Specification Chapter 3 Software 3.1 Operating System Supported ♦ Windows 2000, XP, Vista 3.2 Wireless Mode Supported ♦ AP (Infrastructure) Client mode 3.3 Security ♦ AP (Infrastructure) mode supports ♦ Static WEP that support both 64 and 128 bit keys. ♦ WPA(TKIP) with PSK ♦ Ad-hoc mode supports ♦ None (plaintext) ♦ Static WEP that supports both 64 and 128 bit keys.
Product Specification Chapter 4 Appearance TBD 11
Product Specification Chapter 5 ♦ Specifications Frequency Band: Draft 802.11n Radio: 2.4 GHz 802.11g Radio: 2.4 GHz 802.11b Radio: 2.4 GHz USA – FCC Canada – IC Europe – ETSI Japan – STD-T66/STD-33 ♦ Operating Channels: IEEE 802.11b/g/n compliant: 11 channels (US, Canada) 13 channels (ETSI) 14 channels (Japan) ♦ Transmit Power and Sensitivity: TX Output Power:(Typical) 11g 16.
Product Specification BPSK@6/9 Mbps QPSK@12/18Mbps 16-QAM@24Mbps 64-QAM@48/54Mpb and above, RX up to 150Mbps ♦ ♦ ♦ ♦ ♦ Current consumption(5V DC): TX: 170mA, HT20; 180mA, HT40 at 3.3V RX: 160mA, HT20; 160 mA HT40 at 3.3V Idle: 90mA Radio off 52mA Operating Temperature: 0 ~ 40 oC ambient Storage Temperature: -10 ~ 70 oC ambient Humidity: 5 ~ 90% and must be non-condensing Regulation and certification compliance available: ♦WHQL ♦ETSI/CE ♦ESD: EN61000-4-2, which specifies 4kV contact and 8kV air discharge.
Product Specification References ♦ ♦ ♦ ♦ BRCM Reference Design Functional Specification IEEE 802.11b Standard Specification IEEE 802.11g Standard Specification IEEE 802.11n draft Standard Specification The drawings, specifications and the data contain herein are the exclusive property of Arcadyan Technology Corp. issued in strict confidence and shall not, without the prior written permission of Arcadyan Technology Corp.
Product Specification provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Product Specification IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied.
