RingFlash 100/200 Bedienungsanleitung Mode d’emploi Operating Instructions Gebruiksaanwijzing RingFlash 100/200
Safety Information Safety Information Please read this operating instruction manual thoroughly. Under no circumstances open the device or complete any repair work yourself. Installation location Prevent excessive exposure to smoke, dust, vibration, chemicals, moisture, heat and direct sunlight. Power supply Caution: Only use the power adapter plug supplied because other power supplies could damage the product. Ensure access to the power adapter plug is not obstructed by furniture or such.
Safety information They may contain toxic and ecologically hazardous heavy metals. You are legally obliged to dispose of batteries at the point of sale or at appropriate collection points provided by your local public waste authorities. Disposal is free of charge. The adjacent symbols indicate that batteries must not be disposed of in normal domestic waste and but at authorised collection points. Packaging materials must be disposed of according to local regulations. GB 28 Service−Hotline UK Tel.
Starting Up Starting Up Check the contents of the package Contents RF100 RF200 RingFlash unit 1 1 Power adaptor plug 1 1 Telephone connection 1 1 cable Doorbell unit 0 1 12 Volt battery 0 1 Fixing screws and wall 0 4 plugs Operating Manual 1 1 Connecting the base Connect the base as illustrated in the diagram. For reasons of safety, only use the power adaptor plug and telephone connection cable supplied.
Starting Up In some cases where the amplicomms Ring Flash is used in conjunction with older phones or those phones that do not comply to European Standard ES 203021 connectivity, either the RingFlash or telephone may not function correctly. If this happens you may notice the Ring Flash does not flash or ring or it is not possible to hear dial tone in the receiver when the telephone handset is lifted.
Starting Up ON DP 1 2 3 4 5 6 7 8 ON 1 2 You only need to change the Bell setting if you have more than one Doorbell connected to your RingFlash unit. The two options are provided so that you will know from the colour of the light on the STOP button which Doorbell has been pressed and which Door to answer. Shaker You can plug a shaker accessory (not included) into the socket ‘((o))’ on the back of the RingFlash unit. The shaker will then vibrate when you receive an incoming call.
Your RingFlash 100/200 STOP button Telephone line connection to wall socket Telephone to RingFlash socket Power adaptor socket Shaker socket Rear view Front view Doorbell tone selection (RingFlash 200 only) Ring tone selection Volume control Alarm mode GB Left side 32 Right side Service−Hotline UK Tel. 0844 800 6503 (Using an UK landline, at the time of going to print: calls cost 6p for connection charge and then 5p a minute. Mobile costs may vary.
Using your RingFlash 100/200 Set the ring tone Mode Ring alarm Bell alarm Your RingFlash unit has 3 ring tones 0 Off Bell sound from to choose from. Just move the slider the speaker switch on the left hand side of your product to select ring tone 1, 2 or 3.
Using your RingFlash 100/200 GB 34 Using the Doorbell (RingFlash 200 only) Press the Doorbell button, the red light in the button will turn on. The RingFlash unit will sound the Doorbell tone that you have set (tone 1 or tone 2). Press the STOP button on the RingFlash unit to stop the Doorbell tone. The red light on the Doorbell button will remain on for 1 minute and then turn off.
Using your RingFlash 100/200 Replace the back cover, position and tighten the 4 screws. Refix the Doorbell outside your front door as before. Wallmounting Using appropropriate screws and wall plugs (not supplied), you can wallmount your RingFlash unit using the keyholes on the base. Service Hotline In the case of technical problems, you can contact our hotline service, UK Tel. 0844 800 6503 (Using an UK landline, at the time of going to print: calls cost 6p for connection charge and then 5p a minute.
Maintenance/Guarantee GB 36 Maintenance/Guarantee Maintenance • Clean the product surfaces with a soft, fluff-free cloth • Never use cleaning agents or solvents Guarantee Amplicomms equipment is produced and tested according to the latest production methods. The implementation of carefully chosen materials and highly developed .technologies ensure troublefree functioning and a long service life.
Maintenance/Guarantee purchased the Amplicomms equipment together with the purchase receipt. All rights to claims under the terms of the guarantee in accordance with this agreement must be asserted exclusively with regard to your sales outlet. Two years after the purchase and transfer of our products, claims under the terms of guarantee can no longer be asserted.
Important Notes on the Guarantee Important Notes on the Guarantee The period of guarantee for the Amplicomms product begins on the date of purchase. Rights to claims under the terms of guarantee relate to deficiencies resulting from material or production faults. Rights to claims under the terms of guarantee are annulled following intervention by the purchaser or third parties.
