Owner`s manual

MAX POWE R INPUT 6 0 WATTS RMS
16 OHM PARALLEL JACKS
MODEL GVT112E_
MAX POWE R INPUT 6 0 WATTS RMS
16 OHM PARALLEL JACKS
MODEL GVT112E_
EFFECTS LOOP
RETURN SEND
FOR 100-120 VAC, 50/60Hz: T1.6 AL250V FUSE
FOR 220-240VAC, 50/60Hz: T1 AL 250V FUSE
POWER CONSUMPTION 62W
POWER OUTPUT 15WATTS RMS - CONNECT SPEAKER BEFORE USE
4 OHMS
USE WITH ONE 4 OHM CABINET
OR TWO 8 OHM CABINETS
4 OHMS 8 OHMS 8 OHMS 16 OHMS
USE WITH ONE 8 OHM CABINET
OR TWO 16 OHM CABINETS
REVERB/EFFECTS
FOOT SWITCH
MODEL GVT15H
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES FOR THE U.S. AND ICES-003,
FOR CANADA. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS
DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFER ENCE RECEIVED, INCLUDING INTE RFERENCE THAT MAY
CAUSE UNDESIRED OPE RATION.
WARNING:
DO NOT OBSTRUCT VENTILATION GRILLES
WARNING!
2 PREAMP: 12AX7/ ECC83/7025 2 POWER: 6V6TUBE COMPLEMENT
MAX POWE R INPUT 6 0 WATTS RMS
16 OHM PARALLEL JACKS
MODEL GVT112E_
EFFECTS LOOP
RETURN SEND
FOR 100-120 VAC, 50/60Hz: T1.6 AL250V FUSE
FOR 220-240VAC, 50/60Hz: T1 AL 250V FUSE
POWER CONSUMPTION 62W
POWER OUTPUT 15WATTS RMS - CONNECT SPEAKER BEFORE USE
4 OHMS
USE WITH ONE 4 OHM CABINET
OR TWO 8 OHM CABINETS
4 OHMS 8 OHMS 8 OHMS 16 OHMS
USE WITH ONE 8 OHM CABINET
OR TWO 16 OHM CABINETS
REVERB/EFFECTS
FOOT SWITCH
MODEL GVT15H
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES FOR THE U.S. AND ICES-003,
FOR CANADA. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS
DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFER ENCE RECEIVED, INCLUDING INTE RFERENCE THAT MAY
CAUSE UNDESIRED OPE RATION.
WARNING:
DO NOT OBSTRUCT VENTILATION GRILLES
WARNING!
2 PREAMP: 12AX7/ ECC83/7025 2 POWER: 6V6TUBE COMPLEMENT
Guitar Speaker Enclosures GVT112E / GVT112EW
5
™
Hookup Diagrams
In this example, speaker cables with 1/4" ends connect from each 8 Ω speaker output of the amplifier
[Ampeg GVT15H shown] to one of the speaker inputs of each Ampeg GVT112E and/or GVT112EW speaker
enclosures.
WARNING: Always use good quality (non-shielded) speaker cables. Never use (shielded) instrument cables to
connect speakers to an amplifier.
This is a pretty common setup. A speaker cable with 1/4" ends connects from the 16 Ω speaker output of
the amplifier [Ampeg GVT15H shown] to one of the speaker inputs [both inputs are 16 Ω each] of the Ampeg
GVT112E or GVT112EW speaker enclosure.
WARNING: Always use good quality (non-shielded) speaker cables. Never use (shielded) instrument cables to
connect speakers to an amplifier.