Owner`s manual

EFFECTS LOOP
RETURN SEND
4 OHMS
USE WITH ONE 4 OHM CABINET
OR TWO 8 OHM CABINETS
4 OHMS 8 OHMS 8 OHMS 16 OHMS
USE WITH ONE 8 OHM CABINET
OR TWO 16 OHM CABINETS
REVERB/EFFECTS
FOOT SWITCH
MODEL GVT15H
POWER CONSUMPTION 90W
TUBE COMPLEMENT
2 POWER: 6V6
2 PREAMP: 12AX7/ ECC83/7025
POWER OUTPUT 15WATTS RMS - CLASS 2 WIRING
CONNECT SPEAKER BEFORE USE
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES FOR THE U.S. AND ICES-003,
FOR CANADA. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS
DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR
MOISTURE. DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
AVIS: RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR
Guitar AmplifierGVT15H
6
®
™
The Rear Panel
11 12 13 14 15 16 17
11. AC POWER INPUT WITH MAINS FUSE
ASSEMBLY: The amplifier is equipped
with a detachable power cable that plugs
into the IEC Mains socket on the back of
the amplifier. The AC power cord should
only be plugged into a grounded power
outlet that meets all applicable electrical
codes and is compatible with the
voltage, power, and frequency
requirements stated on the rear panel
of the amplifier.
Do not attempt to defeat the safety
ground connection.
The AC Mains fuse is located in the
IEC Mains socket and is used to
protect the amplifier from electrical
faults. If the fuse needs to be replaced,
please refer to the correct fuse
specifications located on the back panel
of the amplifier.
Never bypass the fuse or replace it with
a wrong type or value.
12. EFFECTS LOOP RETURN: Use this
1/4" TS unbalanced input to return the
processed line-level output of an external
effects processor (for example). The
processor could be fed signals from the
EffectsLoopSend[13].
13. EFFECTS LOOP SEND: Use this 1/4"
TS unbalanced output to send a line-level
output to an external effects processor
(for example). The output here is
affected by all controls including the
Volume[6].
 UsetheEffectsLoopReturnjack[12]
to feed the returned processed signals
back into the amplifier.
14. REVERB/EFFECTS FOOT SWITCH:
ConnecttheGVT–FS2dualfootswitch
to this jack for “remote control” of
Reverb and Effects On/Off. On the
stereo 1/4" plug, the tip controls Reverb
and the ring controls Effects.
When the foot switch is NOT plugged in:
The Reverb is always enabled.
The Effects Loop is active when a cable
isconnectedtotheReturn[12].
When the foot switch IS plugged in:
The Reverb is always affected by the
foot switch operation.
The Effects Loop is controlled by the
foot switch when a cable is connected to
theReturn[12].
The foot switch button for Effects Loop
does nothing when no cable is
connectedtotheReturn[12].
NOTE: A foot switch may be purchased at
your local Ampeg dealer or ordered
directly from LOUD Technologies Inc. Be
suretoaskformodel#GVT–FS2.
15. 4 OHMS:Thetwo4Ωspeakeroutput
jacks are wired in parallel. Use a single
jackwhenusingone4Ωspeaker
cabinet. Use both speaker jacks when
usingtwo8Ωspeakercabinets.Ifyou
havefour16Ωcabinetswithparallel
speaker jacks, you can link all four
16Ωcabinetsina
parallel wiring
configuration,totalinga4Ωload.
16. 8 OHMS:Thetwo8Ωspeaker
output jacks are wired in parallel. Use a
singlejackwhenusingone8Ωspeaker
cabinet. Use both speaker jacks when
usingtwo16Ωspeakercabinets.