Setup guide

B. When prompted, enter the wireless
security key "wireless" and click OK.
A. Click on the Wireless icon to see available wireless
networks (For Vista, click Start > Connect To). Select
the "Amped_Rep_2.4GHz" or "Amped_Rep_5.0GHz"
network and click Connect.
B. When prompted, enter the wireless
security key "wireless" and click OK.
A. Click on the Wireless icon to view available wireless
networks. Select the "Amped_Rep_2.4GHz" or
"Amped_Rep_5.0GHz" network to join that network.
Troubleshooting Tips
Windows 7 and Vista
Mac OS X
I cannot connect to my Home Network. I received an error when running the Smart Setup Wizard.
a. Your Home Network may be secured. Double check that you have the correct security key to connect to
the Home Network.
b. Reboot your Home Network router and try to connect again using the Smart Setup Wizard.
c. Check to see that your Home Network router’s DHCP server is enabled. The Dual Band Range Extender
needs to obtain an IP from your Home Network router.
My Dual Band Range Extender was working fine previously, but now I can no longer access the Internet
through the Dual Band Range Extender.
a. The connection to your Home Network may have been dropped or the router settings may have changed.
Changes to the router could be a result of several events, such as a power outage. When this occurs, connect
to the Dual Band Range Extender and access the setup menu using the web address:
http://setup.ampedwireless.com
Run the Smart Setup Wizard to reconnect the Dual Band Range Extender to your network.
b. The Dual Band Range Extender may be too far from your Home Router and not maintaining a signal strength above
70%. Check the signal strength between the router and the Dual Band Range Extender through the web menu
(left side): More Settings > Management > Repeater Status. The signal strength readout will be under the Home
Wireless Network Settings section. This signal strength must be above 70%. If it is below, move the Dual Band
Range Extender closer to your router, or reposition the Dual Band Range Extender.
I cannot find my Home Network when scanning for wireless networks in the Smart Setup Wizard.
a. The Dual Band Range Extender may be out of range. Move the Dual Band Range Extender closer towards the
wireless router and try the Setup Wizard again from the Web Menu.
b. Make sure that your Home Network’s wireless SSID is broadcasting and not hidden. Hidden SSIDs will require
that you manually enter the SSID into the Wireless Settings > Home Network menu.
I have a dual band router and I cannot repeat a network (or both networks).
a. The Dual Band Range Extender will repeat the 2.4GHz and 5.0GHz signal from your router simultaneously.
To ensure a reliable and strong connection for both wireless networks, make sure that both, 2.4GHz and
5.0GHz wireless networks, have a signal strength above 70%. If necessary, reposition the Dual Band Range
Extender closer to the dual band router to help further maintain a strong connection.
b. Check to make sure that you have the correct security key for both the 2.4GHz and 5.0GHz network of your
dual band router. These keys may sometimes be different from each other.
c. Ensure that your dual band router does not have any security features enabled, such as MAC address filtering,
which may be blocking the connection. If features are enabled, please disable them and run the
Smart Setup Wizard again.
PROBLEM:
SOLUTIONS:
PROBLEM:
SOLUTIONS:
PROBLEM:
SOLUTIONS:
PROBLEM:
SOLUTIONS:
Tips: Trouble Accessing the Smart Setup Wizard
Setting the Dual Band Range Extender’s System Clock
Wi-Fi Protected Setup (One-Touch Setup or Push Button Configuration)
If your wireless adapter has WPS one-touch setup, you can use it when connecting to the Dual Band
Range Extender. Hold down the WPS button on the Dual Band Range Extender (back panel) for 3
seconds. The WPS LED will begin to blink. As it blinks, push the WPS button on your wireless adapter
or enable WPS with the provided software for your wireless adapter.
Using the Features on your Dual Band Range Extender
If you are unfamiliar or want more information on how to set up the security features on the Dual Band Range
Extender, please refer to the User’s Guide on the included CD.
The Dual Band Range Extender is equipped with many powerful security features which can be
accessed through the web menu:
12:26
Wireless Access Scheduling
Control when your Wi-Fi is on/off
Menu Location: 2.4 or 5.0GHz Wi-Fi Settings > Access Schedule
User Access Control
Restrict network access to specific users
Menu Location: User Access
Wireless Coverage Control
Adjust the distance of your wireless network
Menu Location: 2.4 or 5.0GHz Wi-Fi Settings > Wireless Coverage
Web Menu (Left Side)
In order for your Access Schedules and logs to
perform using the correct time stamps and
schedules you will need to set your System Clock.
To do so, go under Management and access the
System Clock tab to sync the System Clock with
your computer’s time.
Amped_Rep_2.4GHz
Amped_Rep_5.0GHz
Amped_Rep_2.4GHz
Autoloading Web Menu
When the Dual Band Range Extender loses its connection with your Home Network, the web menu will automatically load on
your web browser. All web address entries will be redirected to the Smart Setup Wizard of the Dual Band Range Extender. This
redirect feature is meant to notify and help you to easily reconfigure your Dual Band Range Extender in the event of a
disconnection. You may disable this feature through the web menu (left side): More Settings > Network Settings > IP Settings
Wired Port Routing
The Dual Band Range Extender automatically designates the Internet route for all devices connected through the its wired ports. For
example, if you are connected to a dual band network, computers connected to the back of the Range Extender may access the
Internet through your 2.4GHz Home Network or your 5.0GHz Home Network. The Range Extender will automatically select an active
route, however if you feel you need to change these settings you may do so via the web menu (left side): More Settings > Network
Settings > Wired Port Routing
If you continue to have problems accessing the Smart Setup Wizard:
Reboot the Dual Band Range Extender. Disconnect your computer from all wireless networks and try again with the Ethernet cable. If this fails, try...
Disconnect the cable from your computer to the Dual Band Range Extender. Connect via wireless adapter to the Dual Band Range Extender's
wireless network:
Look for the wireless network named: Amped_Rep_2.4GHz or Amped_Rep_5.0GHz. When prompted, enter the security key: wireless
Once connected, open your web browser and access: http://setup.ampedwireless.com. If this fails, contact our support department for assistance.
a
b
PROBLEM: The Setup Wizard does not appear when you enter the setup web address.
SOLUTION: Disconnect your computer from all Wi-Fi networks and try again.
Your computer should be connected to the Dual Band Range Extender with the included Ethernet cable.
If the URL fails to open, then try: http://192.168.1.240
Enter the setup web address into your browser:
http://setup.ampedwireless.com
Disconnect your computer from
all wireless networks.
a
b
Enter http://setup.ampedwireless.com
into your web browser again.
NOTE: Your computer does not need Internet to access the Smart Setup Wizard.
Windows 7:
Click the Wireless Signal icon from bottom right corner.
Select your network and click Disconnect.
Wireless Network
Wireless Network
Right click the Wireless Signal icon from bottom right corner.
Click View Available Wireless Networks, select your network and click Disconnect.
Windows XP:
Amped_Rep_2.4GHz
This login/password is NOT the wireless network key used to connect to your wireless networks.
LOGIN:
PASSWORD:
Setting a Login and Password for the Web Menu
The Dual Band Range Extender does not have
a default login or password to access the web menu.
It is strongly recommended that you change
these settings and select your own personal
login and password. The Password menu can
be accessed through the web menu (left side):
More Settings > Management > Password
If you forget your login and password, you will need to reset the Dual Band Range Extender back to default settings and use the default
login and password (leave login and password blank) to access the web menu. View the instructions above on how to reset the Dual Band
Range Extender back to default settings.
Connecting to the 5.0GHz network requires that you have a 5.0GHz capable network adapter.
How to Share USB Storage Devices
1
2
3
Connect a USB storage device to the USB port on the back panel.
Log on to the web menu at http://setup.ampedwireless.com
and click the USB Storage tab.
Follow the instructions for configuring the settings to share
your USB storage device among locally connected users.
How to Reset the Dual Band Range Extender
to Default Settings
There are two options to reset the Dual Band Range Extender
back to factory default settings:
1
2
Reset the Dual Band Range Extender through the web menu (left side):
More Settings > Management > Save/Reload Settings
Select the Reset Settings to Default button.
Locate the Reset button on the back panel of the Dual Band Range Extender.
Hold down the Reset button for 5 - 10 seconds and release. You may
need to use a pen tip or pin to access the button.
USB Port
Reset Button
Amped Wireless
A Division of Newo Corporation
Copyright © 2012 Amped Wireless / Newo Corporation. All rights reserved.
Amped Wireless, Newo Corporation, the Amped Wireless Logo are registered trademarks or trademarks of Newo Corporation.
If you continue to have issues setting up the High Power Dual Band Range Extender, give us a call — we’re here to help: 888-573-8820
Visit our website for more support information and answers to frequently asked questions: www.ampedwireless.com/support
This is the second page of the Setup Guide. Start on the opposite side first.
High Power Wireless-N 600mW Gigabit Dual Band Range Extender / Repeater
SR20000G
How to Connect your Wireless Computer to the Dual Band Range Extender
v070312