AMPAK WMCT-759B Hardware & Software Setup Guide Rev. 0.0 AMPAK Technology Inc. Doc. NO: www.ampak.com.
1. Download & Install BLE-Stack The latest BLE software can be downloaded at http://www.ti.com/tool/ble-stack?DCMP=wbu-blestack&HQS=ble-stack. After the BLE-Stack software installation is complete, the Prolific driver must be associated with the device in order to use the BTool application. 2. Associate Prolific Driver with WMCT-759B To associate the Prolific driver, you must first connect the WMCT-759B to the PC’s USB port, or to a USB hub that connects to the PC.
2.1 Power on your computer and boot to Windows. Run or double-click the PL-2303 Windows Driver Installer program.( e.g.PL2303_Prolific_DriverInstaller_v1.12.0.exe) 2.2 The InstallShield Wizard will be displayed to inform you that the PL-2303 USB-to-Serial driver will be installed on your computer. Click Next to continue. Figure 2 InstallShield Wizard 2.3 The PL-2303 Driver Installer program will then start to install the drivers needed. Figure 3 Installer program AMPAK Technology Inc. Doc. NO: www.ampak.
2.4 Click the Finish button to close the InstallShield program. If you have plugged the cable into the PC while running the setup installation, please unplug and replug the cable for the system to detect the device. Figure 4 InstallShield Wizard Finish 2.5 Plug in the USB to Serial adapter to the PC USB port. Windows should detect the driver as Prolific USB-to-Serial Com Port. Go to Device Manager and check for the “Prolific USB-to-Serial Com Port” device and the COM port number assigned by Windows.
The “System” window should open up. Click “Device Manager”: Figure 6 Win7 PC, Finding Device Manager A list of all hardware devices should appear. Under the section “Ports (COM & LPT)”, the port should appear. Figure 7 Win7 PC, Connected Ports List Take note of this port number, as it will be needed in order to use BTool. You may close the device manager at this point. AMPAK Technology Inc. Doc. NO: www.ampak.com.
4. Starting the Application BToll On Start-up you should be able to set the Serial Port Settings. Set the “Port” value to the COM port earlier noted in Section 3. Baud rate select 115200. For the other settings, use the default values as shown in Figure 8. Press “OK” to connect to the Host Board Figure 8 BTool, Serial Port settings When connected you should see the screen presented in Figure 9. The screen indicates that you now have a serial port connection to the MWCT-759B Board. AMPAK Technology Inc.
Figure 9 BTool, Overview 4.1 TX test Step1. Select Adv. Command clicking to the “HCI” and found the “HCI_LETransmitterTest”. AMPAK Technology Inc. Doc. NO: www.ampak.com.
Step2. Before establishing a transmitter test, you will want to set up the desired transmission parameters. After parameter setting, click “Send Command” button to begin testing. txChannel= (F-2402)/2 testDataLength= 37 testData=00 AMPAK Technology Inc. Doc. NO: ; L(2402)=0 ; M(2440)=19 ; H(2480)=39 00=PRBS9 ; 01=11110000 ; 02=10101010 www.ampak.com.
Step3 Change TX Channel Step3.1. Select “HCI_LETestEnd” and click the “Send Command” button to end this test. Step3.2. Select HCI_LETransmitterTest and change parameter of txChannel. Click the “Send Command” button to begin testing. AMPAK Technology Inc. Doc. NO: www.ampak.com.
4.2 RX test Step1. Select Adv. Command clicking to the “HCI” and found the “HCI_LEReceiverTest”. reChannel= (F-2402)/2 ; L(2402)=0 ; M(2440)=19 ; H(2480)=39 step1.1: Press the “Send Command” button to perform RX test. step1.2: Using instrument to transmission packets. step1.3: Perform HCI_LETestEnd, in message log window can find the number of received. AMPAK Technology Inc. Doc. NO: www.ampak.com.
Step2. Change RX Channel Please refer to Section 4.1 step 3. AMPAK Technology Inc. Doc. NO: www.ampak.com.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This device is intended only for OEM integrators under the following conditions: 1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 condition above is met, further transmitter test will not be required.
第十二條→經型式認證合格之低功率射頻電機，非經許可，公司，商號或使用者均不得擅 自變更頻率、加大功率或變更原設計之特性及功能。 第十四條→低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象 時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工 業、科學及醫療用電波輻射性電機設備之干擾。 模組請加註 1. 本模組於取得認證後將依規定於模組本體標示審驗合格標籤 2. 系統廠商應於平台上標示「本產品內含射頻模組: AMPAK Technology Inc. Doc. NO: www.ampak.com.
