AMPAK AP6212SD Evaluation Kits User manual Version 1.0 AMPAK Technology Inc. Doc. NO: www.ampak.com.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions: 1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
Industry Canada statement: This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.
l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product.
l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel.
DETACHABLE ANTENNA USAGE This radio transmitter (IC: 11956A / Model: AP6212SD) has been approved by ISED to operate with the antenna type listed below with maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均 不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干 擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設 備之干擾。 1. 本模組於取得認證後將依規定於模組本體標示審驗合格標籤。 2.
1. AP6XXX Evaluation Board Introduction AP6212SD Evaluation board (EVB) likes as figure1. That is designed for IEEE802.11 b/g/n WLAN with integrated Bluetooth application. It is subject to provide a convenient environment for customer’s verification on WiFi or Bluetooth function. There are many controller pins and reserved GPIO on Evaluation board which describes as below. Figure1. Top view of AP6212SD EVB Interface highlights: 1. U1: AP6212SD SIP module. 2.
or Dipole antenna. 13. Ct1 - Ct4: WLAN and BT control pins, strongly recommended WL_HWAKE(IRQ) connected to MCU. 2. WiFi function verification step WIFI SDIO: Using external pull up resistors depends on the SDIO supply voltage. For 1.8V, the resistance range is 30KΩ~82KΩ. For 3.3V, its range from 21 KΩ~41 KΩ on the four data lines and the CMD line as the following circuitry. VIO_3V3 R7 R6 J8 SD2 SD3 SDCMD GND 3.
Figure3. Bluetooth verification connection interface to Host UART Hardware Setup: v Refer to Figure3 UART pin definition connects the J1 interface of AP6XXX evaluation board to Host UART control interface. v Connects an external antenna at SMA connector on the evaluation board. v Note to the VDDIO voltage level should be the same as GPIO voltage level of Host CPU. WiFi and Bluetooth software setup: Please follow up software guideline of Ampak official released. AMPAK Technology Inc. Doc. NO: www.ampak.
