USER MANUAL LC26T 31 E/LC32T 3 1E
Contents Safety Precautions 1 Important Safety Instructions 2 Accessory List 4 Overview of TV i. Front Panel Description 5 ii . Back Panel Description 6 Remote Control Overview 8 Remote Control Operation 9 Connection i. Antenna Connection 10 ii. YPbPr/YCbCr (component) Connection 11 iii.S-Video and Video (Composite) Connection iv. VGA Connection 12 12 v. Scart Connection 13 vi. HDMI / DVI Connection 14 Basic Operation 15 Button Instruction 17 Menu i. Picture Menu 19 ii.
Safety Precautions This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Important Safety Instructions 12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, please take caution when moving the cart to avoid injury from tip-cover. 1.Read These Instructions All the safety and operating instructions should be read before the product is operated. 2.Keep These Instructions The safety and operating instructions should be retained for future reference. 3.
Important Safety Instructions 17.Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal . 18.
Accessory List Please check the accessories and ask the local dealer for help when they are lost or damaged. POWER MUTE SOURCE LAST SOURCE OK DTV/TV MENU DTV MENU FAV EXIT FAV- FAV+ GUIDE 1 2 4 5 3 LIST 6 DISPLAY i 7 8 9 0 DUAL TXT/MIX Quick Start CH+ VOL VOL CH- SUBTITLE AUDIO PAGE ASPECT FREEZE VIDEO OFF VOG Power Cord (×1) User’s manual CD (×1) and Quick Start(×1) Remote control (×1) "AA" size battery (×2) Note: Please use the power cord which includes the ground wire.
Front Panel Description Overview of TV 1 1 3 2 4 5 1 Speaker 2 Remote control sensor 3 Standby indicator 4 SOURCE 6 7 8 Press it to display the menu of the available viewing source. 5 MENU Press it to display the OSD menu. The button also acts as select button "OK" in source menu. 6 CH+/Press it to choose the channel. The two buttons also act as direction buttons 7 VOL+/Press it to adjust volume . The two buttons also act as direction buttons 8 in menu display.
Back Panel Description Back Panel of Model: LC32T31E Rear interface Rear interface description 100-240 V 50/60HZ POWER COMPONENT IN VGA AUDIO IN EXT1 VGA IN OPTICAL ANTENNA EXT2 HDMI - 1 IN HDMI - 2 IN Side interface: AV IN Video input Audio input S-Video input Headphone Output Power Switch Notes: 1.The service only interface is used to upgrade and service . Without permission, please don’t connect. 2. When input the earphone, the speaker is silent.
Back Panel Description Back Panel of Model: LC26T31E Rear interface Rear interface description 100-240 V 50/60HZ POWER VGA IN OPTICAL COMPONENT AUDIO VGA IN IN AUDIO IN EXT1 ANTENNA EXT2 HDMI - 1 IN HDMI - 2 IN Side interface: AV IN Video input Audio input S-Video input Headphone Output Power Switch Notes: 1.The service only interface is used to upgrade and service . Without permission, please don’t connect. 2. When input the earphone, the speaker is silent.
Remote Control Overview Standard Remote Control POWER Standby button MUTE Mute SOURCE Main source Teletext Page up LAST SOURCE OK Last source DTV/TV *DTV/TV Enter OSD setup mode MENU EXIT Direction buttons Enter Teletext Page down Exit Colour (red/green/yellow/blue) buttons DTV MENU FAV FAV- FAV+ Fav, Fav-, Fav+ * *DTV Menu GUIDE *Guide 1 2 3 4 5 6 7 8 9 0 DUAL LIST Channel list Numerical buttons DISPLAY Display status i TXT/MIX Txt/Mix Last channel Next /Previous ch
Remote Control Operation Remote control direction Batteries Installation Push as the arrow shows to take off the back cover. Point the remote control at the remote control sensor. TEAC Insert the batteries with correct polarity. 30 30 POWER MUTE SOURCE LAST SOURCE OK DTV/TV MENU DTV MENU FAV EXIT FAV- FAV+ GUIDE 1 2 4 5 6 7 8 9 0 DUAL 3 LIST DISPLAY i TXT/MIX CH+ VOL VOL CH- SUBTITLE AUDIO PAGE ASPECT FREEZE VIDEO OFF VOG Put the cover back as the arrow shows .
Connection Antenna Connection Indoor Antenna Connection Typical Wall antenna jack used in apartment buildings, connect the antenna cable as shown below (Please use the correct type of antenna cable according to the type of wall antenna jack). 75 ohm Round Cable Bronze Wire 300 ohm Flat Wire Apartment buildings ANTENNA Antenna Converter Wall Connection Jack *If you have a 75 ohm round cable, insert the bronze wire and then tighten the connection nut.
Connection YPbPr/YCbCr (Component) Connection Y Suit for 26" Pb/Cb - - DVD , etc Pr/Cr AUDIO(L) AUDIO(R) Suit for 32" Audio Cable YPbPr/YCbCr Cable Note: Please refer to the illustration above to connect TV with DVD player or other component signal sources. Connect the YPbPr/YCbCr Cable and Audio Cable to corresponding jacks of the DVD player or other component signal sources. Please select "Component" in the source menu when you connect component signal source.
Connection S-Video and Video (Composite) Connection S-Video or composite signal output POWER VCR VIDEO AUDIO(L) AUDIO(R) S-VIDEO AV-3 IN AV IN VIDEO AV Cable AUDIO-L AUDIO-R S- Video Cable S-VIDEO Note： 1.Please refer to the illustration above to connect TV with composite signal sources. Connect composite video cable and audio cable to corresponding jacks of DVD player or other composite signal sources. Please choose "AV" in the source menu when you connect DVD player or other sources.
Connection Scart Connection DVD , etc - - 1 Scart Scart Cable Note: 1.Please refer to the illustration above to connect TV with DVD player or other devices. 2 . Connect Scart Cable to the corresponding jacks of DVD player or other devices. 3. Please select "EXT1", " EXT2 " in the s ource menu when you connect DVD player or other sources with Scart connection. 4.The signal type input to EXT1 will be detected automatically. 5.
Connection HDMI/DVI Connection Picture A HDMI - 1 IN DVD1 DVD2 HDMI HDMI HDMI - 2 IN HDMI Cable HDMI Cable VGA AUDIO IN HDMI1 IN DVI HDMI2 IN AUDIO(R) AUDIO(L) DVI HDMI / DV I Cord HDMI / DV I Cord Audio Cord Audio Cord Picture B AUDIO(R) AUDIO(L) Picture C Connet TV with corresponding jacks on DVD or STB, and switch the source to HDMI in Source menu. (Picture A/B/C) 1. If connecting with an HDMI cable, it is not necessary to connect an audio cable (Picture A). 2.
Basic Operation Power on / Power off 1.Plug the power cable into the power socket . M ake sure the output voltage and frequency of the power is consistent with this machine. 2.Power on the switch on the side cover, the red light on the front board will be lighted, then the TV enter standby mode. Press "POWER" touch key on the front board, the indicator change into green. The TV enter Play mode. 3.
Basic Operation Initial Auto Installation Auto Search 5 6 Auto Search Press "EXIT" button to stop the auto search, but you are recommended not to stop it during the search process since the initial autoinstallation functions only once. You do not need to do anything during the auto search. Current Channel 9 104.25MHz After the auto search finished, the finishing sign menu will display on the screen. Then the TV will display at channel one.
Button Instruction Browse The Channel List LIST ● Press "LIST" button, the channel list will display on the screen. Channel list Channel Frequency 1 2 3 4 5 6 7 8 9 10 Sound System 144 . 28 B/G ------------------- ------------------- Channel Name --------------------- Skip Channel Off On On On On On On On On On Use direction buttons to select specific channel. Use " " PAGE PAGE " and " button to switch the listing page. Press the "EXIT" button to quit.
Button Instruction Last Source LAST SOURCE ● Press this button to switch between the last signal source and the current one. For example, when the signal source is TV, last source is AV, press this button to switch to AV and press it again to return to TV. Freeze Image FREEZE ● Press this button to freeze the current displaying image, and again to exit the freeze mode. Note: It is only available when input SD signal.
Menu Picture Menu You can adjust the Picture to get your desired picture effect. Picture 1 2 Press the "MENU" button to enter Picture menu. Press " " buttons to select "Picture Mode". Picture Mode Picture Mode User Brightness 50 Contrast 50 Colour 50 Tint 0 Sharpness 6 User Picture Mode Press " / " buttons to select your favourite mode. Only i n the "User" mode, you can adjust Brightness, Contrast, Colour, Tint, Sharpness.
Menu Channel Menu Sound System Channel 1 Press "MENU" button to select "Channel " menu. 2 Press " 3 Press " " buttons to select the suitable system for local TV signal. Press "EXIT" button to quit. 4 " buttons to select " Sound System" . D/K Sound System Current Channel 12 Skip Channel Off Rename Channel ... Exchange Channel ... Auto Search ... Manual Search ... Fine Tune ...
Menu Channel Menu Exchange Channel You can exchange the current channel with another channel, please refer to "Exchange Channel". 1 Press the "MENU" button to select "Channel" menu. 2 Press the " 3 4 5 Press the " " buttons to select " Exchange Channel " . " button to enter this menu. Input the Channel Exchange number (the maximum number is 99), then press " OK " button to save your setting.Then the two channels are exchanged. Press "EXIT" button to exit "Channel Exchange" mode.
Menu Channel Menu Manual Search You can also set program list again step by step to "Manual Search" function. Channel 1 2 3 4 Press the " MENU " button to select "Channel" menu . D/K Sound System Current Channel 12 Press the " " buttons to select " Manual Search ". Press the " "button to enter "Manual Search". Skip Channel Off Auto Search ... Press " Manual Search → ... / ... Rename Channel ... Exchange Channel " buttons to search channels.
Menu Window Menu Aspect Window You can adjust the aspect as your desired. Aspect ratio Full Screen H Position 255 Press "MENU" button to select "Window" menu. V Position 0 Frequency 128 Press " Phase " buttons to select " Aspect Ratio ". 9 ... Auto Adjust Press "◄/►" buttons to select "Aspect Ratio".
Menu Setting Menu OSD Position 1 Press "MENU" button to select "Setting" menu. 2 Press " " buttons to select " OSD Position ". S e tting OSD Language English OSD Position Center Opaque OSD Background Teletext Language 3 Press "◄/►" buttons to select your wanted OSD position. EXT2 CVBS Blue Screen 4 Press " EXIT" button to quit. Western Europe On Sleep Timer Off Colour Temperature ... OSD Background 1 Press "MENU" button to select "Setting" menu.
Menu Setting Menu Sleep Timer Press " MENU" button to select "Setting " menu. Press " / " buttons to select "Sleep Timer ". Press the " " buttons repeatedly to select the duration from current to the time TV switching to standby automatically. You can select Off /10/20/30/60/90/120/180/240 minutes. For example: The current time is 8:25.You can set the timer of 30 minutes. Then the TV will be switched to standby mode in 8:55 automatically.
Teletext Teletext is an information system broadcast by certain channels which can be consulted like a newspaper. It also offers access to subtitles for viewers with hearing problems or who are not familiar with the transmission language (cable networks, satellite channels, etc.). Teletext Language Selection. The default Teletext Language is Western Europe. If the Teletext language is not Western Europe in your region, please kindly change the language according to the instruction in P24.
Troubleshooting And Maintenance Troubleshooting Please read this user's manual before using the TV set. If you have any troubles in using this TV set, try to solve it by the suggestions mentioned below. If you can not remove the trouble after adopting corresponding suggestions, please contact the technical service center or dealer authorized by us. For the sake of your safety, please do not open the cover and repair it by yourself, or it may cause further damage to the TV set, electric shock or fire.
Troubleshooting And Maintenance Maintenance Screen Burn A characteristic of Plasma and LCD TV Panels is that displaying the same image for a long period of time may cause a permanent after-image to remain on the screen. This is called screen burn. Most pictures shown on your TV will be constantly moving and fill the screen. Examples of images that you need to watch out for are as follows (this is not an all-inclusive list): 1.
Display Mode Both screen position and size will vary depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported: VGA: Resolution Horizontal Frequency （KHz） Vertical Frequency （Hz） 640X480 31 . 5 60 . 000 800X600 37.9 60.000 1024X768 48.4 60 . 000 1280X960 60 . 000 60.000 1280X1024 63 . 981 60 .
-30-
This symbol on the product or in the instructions means that your electrical and electronic equipment should be disposed at the end of life separately from your household waste. There are separate collection systems for recycling in the EU. For more information, please contact the local authority or your retailer where you purchased the product. AMOI ELECTRONICS CO ., LTD . 45 TIYU RD , XIAMEN , FUJIAN 361012 , CHINA Http: // www.amoi.
