....~.:;:rFLEElWOOD. Driven to Explore ©2004 by Fleetwood Enterprises, Inc. All rights reserved. No part of this publicatiou may be reproduced or transmitted in any [onn or by any means, electronic or mechanical, including photocopying, recording, 01' by any infonnation storage or retrieval system without written pennission from Fleetwood Enterprises. Inc. Manufacturing subsidiaries of Fleetwood Enteq)rises, Inc. build the following motor homes, travel trailers and truck campers: Pace Arrow.
---- 1- - - TABLE OF CONTENTS NTR0DUCTION ..................... .01-1 Inspect and Maintain ...................01-2 Planning and Preparation ................01-2 Owner's Information Package ............01-2 Chassis and Vehicle Identification ........01-3 Suspension Alignment and Tire Balance ....01-3 After-Market Steeling Aid Devices ........ 01-4 Warnings, Terms and Concepts for Safe Operation of Your Motor Home ....01-4 Event Data Recording Device (If Equipped) .......................01-6 WARRANTY ......
Table of Contents Windows ............................06-2 Emergency Exit Window(s) ............06-2 Remote Mirror Control (If Equipped) ......06-2 Sun Visors (If Equipped) ...............06-2 Window Shades (If Equipped) ...........06-2 Day/Night Shades (If Equipped) ....... .06-3 Mini-Blinds ..........................06-3 Storage ..............................06-3 Exterior Compartments . ..............06-3 Interior Storage .....................06-4 Slide-Out Rooms (If Equipped) ......... .
I t---- Table of Contents Using LP Gas System at Low Temperatures .......................09-3 Filling LP Gas Tanks ...................09-3 LP Gas System Check ..................09-3 LP Gas Leak Detector/Alarm ............09-3 Lighting LP Gas Appliances .............09-4 .PPLIANCES ........................ .10-1 Water Heater ........................ .1 0-1 Water Heater Bypass Valve ........... .10-1 Refrigerator ......................... .10-1 Furnace .............................1 0-1 Range .............
This. page intentionally blank.
1----- ~ INTRODUCTION Welcome to the recreational vehicle life-style and the growing family of motor home owners. We sincerely thank you for choosing a Fleetwood motor home! .1'1 NOTE 1 This manual describes many features of your RV and includes some instructions for its safe use. This manual, including photographs and illustrations, is of a general nature only.
Introduction If you have any questions regarding operation, maintenance, or service, please contact your dealer immediately so he can assist you. Your dealer's Service or Sales Department will handle any normal problems which might occur. Some equipment and features described or shown in this manual may be optional or not available on some models. Because of the continuous program of product improvement conducted by Fleetwood, it is possible that recent product changes may not be included in this manual.
1-- Introduction CHASSIS AND VEHICLE IDENTIFICATION SUSPENSION ALIGNMENT AND TIRE BALANCE Several numbers are used to identify the vehicle andcomponents used on the vehicle. The front suspension and steering system of this vehicle was accurately aligned at the factory before delivery to the dealership. However, after you have fully loaded the vehicle according to your personal needs, have the alignment checked and adjusted, if necessary.
1--}------- Introduction Excessive or abnormal tire wear may indicate worn or misaligned suspension or steering components, unbalanced or improperly inflated tire(s) or some other tire/suspension problem. Alignment can be affected by worn steering/suspension parts or road hazards such as hitting a curb, pothole, railroad track, etc. Improper alignment can cause tires to roll at an angle and wear unevenly. It may also cause the vehicle to "pull" to the right or left.
Introduction or other loads behind your motor home. The maximum amount of weight your motor home can pull or stop is determined by the manufacturer of the chassis on which your motor home is built. Check the Chassis Operator's/Owner's Guide/ Manual provided by the motor home chassis manufacturer for the limits on the weight you can tow. If the Chassis Operator's/Owner's Guide/ Manual equipped with your motor home does not provide specific information on towing weight limits.
1-- h-- Introduction EVENT DATA RECORDING DEVICE (If Equipped) SPECIAL NOTICE: Vehicle Event Data Recording Capabilities. Motor homes equipped with driver/passenger airbags, Navigational or Vehicle Avoidance Systems and/or equipped with certain other electronic devices may be equipped with event data recording capabilities. Your motor home is built on a vehicle chassis supplied by an automotive manufacturer.
LIMITED ONE-YEAR WARRANTY For Motor Homes Manufactured by Subsidiaries of Fleetwood Enterprises, Inc., Sold In the United States and Canada COVERAGE PROVIDED Your new motor home, including the structure, plumbing, heating and electrical systems, all . appliances and equipment installed by the manufacturer, is warranted under normal use to be free from manufacturing defects in material or workmanship, when first sold by an authorized Fleetwood Dealership.
warranty WHAT IS NOT COVERED BY THIS WARRANTY This warranty does not cover: 1. The automotive chassis system (including the ,chassis and drive train), tires and batteries, which are covered by the separate warranties of the respective manufacturers of these components. 2. Defects caused by or related to: a. Abuse, misuse, negligence or accident; b. Failure to comply with instructions contained in the Owner's Information Package; c. Alteration or modification of the motor home; d.
Warranty WARRANTIES Your motor home is covered by one of the most comprehensive warranty programs in the RV industly. Please refer to the warranty in this section. It explains your rights and obligations, as well as the rights and obligations of the dealer and manufacturer. Please read this section carefully. You will be better informed in case you have a warranty-related problem, and your dealer will be better able to get you on the road again.
Warranty WARRANTY SERVICE If you need service or warranty information, please see the booklets and other documents included in your Owner's Information Paclwge. When contacting any of the equipment manufacturers, always have the model and serial numbers available. Appliance identification numbers wiIl be found on tags or plates attached to the appliance. If you ever need warranty work done, be sure to have the right papers with you.
IMPORTANT NOTICES State laws in the United States and provincial laws in Canada V8J'Y concerning operator licensing requirements and vehicle dimensional restrictions. Check the laws in the area where you anticipate traveling. The particle board. hardwood plywood, or paneling used in your motor home are made with urea-formaldehyde resin. The companies that supply us with these materials have asked that we tell you about urea-formaldehyde with the statements on this page.
Important Notices A. WARNING A. WARNING LP gas regulators must always be installed with the diaphragm vent facing downward. Regulators that are not in compartments have been equipped with a protective cover. Make sure that regulator vent faces downward and the cover is kept in place to minimize vent blockage which could result in excessive LP gas pressure causing fire or explosion.
1.. -~ --- PACE ARROW INFORMATION LAMPS AND BULBS Interior - 12-volt Floor Light ""." .... ".".".""" ... "".,,.GE 53, 12-volt Ceiling IS" fluorescent...GE F-15TS-WW, 12-volt Dinette decor light """""""""""""C-921, 12-volt Bedroom decor lights """""""""".C-921, 12-volt Range hood .. "" ... " .. ""."" ... """.""".5125, 12-volt Bathroom vanity light """"""""""".l3W, 12-volt Living area decor light """"""""".
Pace Arrow Information DRIVER'S CONTROLS It) It) N It) T'" T'" j 6<:1 £( - 0 - C') ~~ I '--.., T'" '-c- , - I I I I II I II I / I"l"T'" T'" T'" 01 co / / C') '\. , 0 ""~ J~/ l/N OP' , ~ , ~ T'" ~ G co T'" 0 , "- '"~~ "".
1. Headlight Switch 2. Auxiliary Start Switch 3. Instrument Clnster - (Consult Chassis Operator's! Owner's Guide!Manual for details on instruments.) 4. Generator Honr Meter 5. Cigarette Lighter!Access. PIng 6. Generator Start Switch 7. Radio Mode Switch - Switches power to the radio between the chassis battery and the coach battery. Fan Speed Control Knob - Turns fan on and off and adjusts speed. AlC Button - When button is pressed in and light is on, cooled air is delivered through selected outlets.
1- ~ Pace Arrow Information HOOD LATCH To open front hood door: 1. Unlock hood door locks. 2. Reach over top center of hood door, pull paddle lever toward hood, pull top of hood outward and lift hood door upward.
ON THE ROAD MOTOR HOME LOADING Responsibility for Proper Loading As the operator of this motor home, you are responsible for its pIDper and safe loading. This section is intended to pIDvide you with helpful infolmation conceming the loading of your motor home. Your motor home chassis is designed to carry a specifically rated maximum weight.
On The Road Towing a Vehicle or Trailer o ("Towed Load or Towed Unit") v'1 NOTE I Some states and provinces require brakes and safety chains when towing vehicles. Consult the proper authorities in the states or provinces through which you will be traveling. When you use your motor home to tow, remember that you must stop the towed load with your motor home's brakes. This is critical on hills and in the mountains where you may encounter shmp cW'ves and possibly iITegulm' road surfaces.
On The Road CARGO CARRYING CAPACITY PRODUCT: _ _ _ _ _ _ _ _ _ YEAR: _ _ _ MODEL: _ _ _ _ _ _ SERIAL NO: _ _ _ _ _ _ _ __ FIN NO: _ _ _ _ _ _ _ __ pounds (kilograms) GVWR minus UVW minus fresh water weight of ___ gallons @ 8.3 Ib/gal minus LP gas weight of ___ gallons @ 4.2 Ib/gal minus SCWR weight of ___ persons @ 154 Ib/person CCC for this motor home' 'Dealer installed equipment and towed vehicle tongue weight will reduce CCC. Consumer's should request such information from the dealer.
On The Road what you are towing can avoid this risk and make your driving and towing experience safer and more enjoyable. Cargo Carrying Capacity and Load Distribution .1'1 NOTE 1 Cargo Carrying Capacities (CCC) of your motor home are specified on a label affixed to the inside of the motor home. The label includes all factory installed options. If other equipment such as leveling jacks, awnings, roof pods, etc.
On The Road this time, use only one side of the scale, as shown on the following pages. To calculate the opposite side of the vehicle wheel position weight, subtract this side's weights from the weights recorded in steps 1, 2 and 3. If there is a towed vehicle, proceed to step 4 to obtain the "towed vehicle only" weight. 4.
1--1----- On The Road WEIGHING YOUR MOTOR HOME To Obtain Individual Wheel Positions Weights: STEP IS :: 1 STEP3S I 31 One Side Scale Weight I: I Ibs. One Side Scale Weight Ibs. (Step 1 - 1S) Tire Load (Ibs.) Ibs. Calculate Other Side Weight Ibs. (Step 3 - 3S) Ibs. Tire Load (Ibs.) (See Note') (See Note') Inflation Ibs. (Step 3S) (Step 1S) Calculate Other Side Weight ]I psi. Inflation psi.
On The Road A CAUTION Modification of your vehicle by addition of racks not originally equipped by the manufacturer to carry additional equipment, vehicles or cargo will reduce your warranty coverage and may cause personal injury or property damage. A WARNING Do not store or carry LP gas containers, gasoline, or other flammable liquids inside your motor home.
On The Road Air Pressure The most important factor in maximizing the life of your tires is maintaining proper inflation. Driving on a tire that does not have the correct inflation pressure for the load of the vehicle is dangerous and may cause premature wear, tire damage, and/or loss of control of the vehicle. A tire that is underinflated will build up excessive heat that may go beyond the prescribed limits of endurance of the rubber and the radial cords. This could result in sudden tire failure.
, i------- On The Road dual, you might also spot it with a visual inspection, However, if it is an inside rear dual, the chances of spotting it without an air pressure check are very slim. If you begin driving without finding it, velY quickly (in most cas"s a few miles) your outside rear tire next to the low air pressure tire is going to heat up from canying double its load, which will cause both tires to fail.
On The Road A. WARNING However, if you brake hard, comer hard or if your vehicle receives an impact, the lap and shoulder belt locks and prevents you from moving. Make sure that you and your passengers, including pregnant women, wear safety belts. Be sure that lap belts fit snugly and as low as possible around the hips. If safety belts are not used properly, the risk of you or your passengers being injured in a collision greatly increases. A.
1--- On The Road Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather, and could bum a child. Check seat covers and buckles before you place a child anywhere near them. Children who are too large for child safety seats should always wear safety belts. -A. WARNING Never leave a child unattended in your vehicle. Always remove the key from the ignition and take it with you.
On The Road A. WARNING An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle. Use only the specified anchor positions to secure a child restraint requiring top tether strap(s). DRIVING AND VEHICLE CONTROL Driving your motor home will be different from driving your family car or truck.
On The Road and/or obstmctions near your motor home. You must monitor them constantly while you are driving. Become familiar with the operation of the side minurs and leam to use them to view objects and the road beside and behind the motor home. The rear view mirrors are controlled from a panel located on the driver's left side instmment panel. To adjust the mirrors, select either LEFT or RIGHT mirror and press the appropriate arrow.
On The Road displayed on a screen in the driver's compartment. The monitor screen may be overlaid with a distance scale reference which gives approximate distance of objects to the rear of the motor home. The rear view video monitor works in two modes: Mode 1 - Standby (Indicator will be lit to green) 1. Thrn on the ignition switch. 2. Shift the transmission to [Rjeverse. 3. Monitor on. Mode 2 - On (Indicator will be lit to amber) 1. Thrn on the ignition switch. 2. Monitor on.
On The Road • Do not sllloke, light lIIatches or lighters while refueling at the pUIIIP or when using gasoline anywhere else. • Use only the refueling latch provided on the gasoline dispenser nozzle - never jalll the refueling latch on the nozzle during refueling. A. WARNING Certain fabrics, clothing and/or shoe apparel may potentially create an electrostatic charge, which may not immediately discharge upon exit of your motor home.
On The Road ENGINE FAN When the engine is under load or requires maximum cooling, the engine fan turns faster. The fan may become noisy at high speed and when maximum cooling is required. High speed fan noise can sometimes be misinterpreted as transmission slippage. This is not the case. This fan noise indicates that the fan is doing what it is supposed to do. This noise is not a defect in the fan or the transmission.
i--- On The Road Carbon Monoxide Detector/Alarm Your motor home is equipped with a carbon monoxide (CO) detector/alarm. If the detector/alarm sounds, it is an indication that unacceptable levels of carbon monoxide gas are present. This may occur in traffic concentrations or in campgrounds where other vehicles as well as your motor home are contributing to the carbon monoxide level in the surrounding air. Sounding of the detector/alarm does not indicate a faulty detector/alarm.
This page intentionally blank.
1-.. . --LIVING WITH YOUR MOTOR HOME LEVELING SYSTEM (If Equipped) Controls for the leveling system are located in the driver's compattment. A detailed operating and maintenance guide is included in your Owner's Information Packoge. Read all instlUctions for this system carefully before operating the system. A WARNING The leveling system is designed as a leveling system only. Do not use the system as a jack or with a jack. Do not attempt to raise the tires off the ground.
1 --1 If--- Living With Your Motor Home WINDOWS REMOTE MIRROR CONTROL Windows in your motor home are either slider or torque pane type. Open slider windows by rotating the locking lever and sliding the window. Open and adjust torque windows by turning the knob or crank located at the bottom of the window frame. On your ventilating windows, water is trapped by the frame. During a heavy downpour or washing, water may be seen in the lower portion of the frame.
Living With Your Motor Home STORAGE Exterior Compartments Exterior storage compartments should accommodate most of your storage needs. All of the storage compartments, except the LP gas tank comp31tment, can be locked. Fire prevention regu ations require that the LP gas tank comp31tment be unlocked at all times. Day/Night Shades (If Equipped) The day/night shades are dual-purpose window covering that provide privacy at night and light control during the day.
1-i------ Living With Your Motor Home Interior Storage The closets and cabinets have catches along one edge of the door. Pull on the cabinet door handle to open. Overhead doors have supports to hold them open. Drawers rest in notches when they are closed. To open drawers, lift up slightly, then pull open. Glosets may be equipped with 12-volt lights that turn ON when the closet door is opened. Be sure the light goes OFF when the closet door is closed - your battery will be discharged if it stays ON.
Living With Your Motor Home 3. Raise front portion of table several inches to disengage inserts from the wall supports. 4. Lower table top to the dinette frame to complete the bed base. 3. Pull upward on the cen.ter (If the metal bar, and rotate it down slowly until the wood bars rest on the floor.' To restore the sleeper sofa: S. Slide seat and back cushion into place over the bed base. 1. Lift the front edge of thebedframe up and rotate it back.
i-----~ Living With Your Motor Home A WARNING Loose furniture must be secured before travel. Failure to do so may result in injury or death in the event of an accident or emergency maneuver. Interior Lighting Both decorative and 'utility' style 12-volt lighting fixtures may be used in your motor home. Utility style fixtures may be either single or dual. A slide switch selects either single or dual brightness. For your convenience, some lights are operated from wall switches.
Living With Your Motor Home 2. Press BATTERY rocker switch on the panel. 3. Turn on a light or any 12-volt appliance. The battery must be checked with a load. 4. Read battery condition on the indicator. EFFECTS OF PERMANENT OCCUPANCY Condensation and How to Control It You need to understand how to properly manage and control the humid conditions and condensation that you may experience. RVs are much smaller than a house, and are tightly built.
Living With Your Motor Home Clothes drying - After 10 pounds of clothes have been washed and spin-dried in a washer, they still contain about 10 pounds of water. If these clothes are dried inside, that water is released into the air in the RV. Gas appliances - When LP gas is burned, carbon dioxide, nitrogen and water are given off into the air. For every 1000 cubic feet of LP gas burned, nearly 88 pounds of water is released into the air.
Living With Your Motor Home CAUTION Do not heat the RV interior with the range or oven. Open flames add moisture to the interior air. Do not use an air humidifier inside the R\I. Water put into the air by the humidifier will increase condensation. A WARNING Never use open flame gas or kerosene-burning heaters indoors. These devices release water into the air, and the exhaust gases contain poisonous substances. A WARNING Do not cover emergency exit window(s).
li--------'1;""--- Living With Your Motor Home perate climate. The best growth occurs at temperatures between 40°F and lOO°F. Most importantly, mold growth requires moisture, and moisture is the only growth factor that can be controlled. By minimizing interior sources of moisture, an RV owner can reduce or prevent mold growth. However, if optimal growth conditions persist, mold can develop within 24 to 48 hours.
Living With Your Motor Home nizing the danger and practicing common sense, safety and maintenance habits. Know where your fire extinguisher is located and how and when to use it. Read the instlUctions on the fire extinguisher. Remember that portable fire extinguishers are intended for use by the occupants of a building or area that is threatened by fire. They are most valuable when used immediatelyon small fires.
Living With Your Motor Home Smoke Detector/Alarm A battery-powered smoke detector/almm is mounted on the ceiling in the living/cooking area of your motor home. Please read the smoke detector/alarm operating instlUctions for details on testing and caring for this impOltant safety device. Test the smoke detector/alarm after the motor home has been in storage, before each trip, and at least once a week during use.
1---PLUMBING SYSTEMS AND HOLDING TANKS The plumbing systems in your motor home are constructed of durable thermoplastic materials. Holding tanks and piping components are strong, lightweight, and con'Osion resistant. Holding tanks are of three types: • Fresh - Fresh potable water • Grey - Lavy/shower effluent • Black - Toilet effluent It is recommended to discharge as many fluid tanks as practical before driving.
Plumbing Systems and Holding Tanks CAUTION Overfilling the fresh water tank from a pressurized source may cause damage to the water system. Monitor water tank filling continually. 2. Gravity fill -The external gravity water fill is located on the exterior of the motor home. The on-board water tank can be filled here. To fill the fresh water tank, remove the cap, remove the vent plug, and fill the tank using a potable water hose.
Plumbing Systems and Holding Tanks Low Point Drains To dl"ain hot and cold lines: 1. Open hot and cold low point drains" 2. Open the shower handle and faucet until all water has drained from the lines. Troubleshooting the Fresh Water System Water system problems usually fall into two categories: Inherent system problems, and problems caused by neglect. System problems are usually the result of road vibration and campsite water pressure variations.
Plumbing Systems and Holding Yanks 6. Flush the system with potable water. Let the fresh water flow through the system for several minutes to flush out the chlorine solution. 7. After you stop the flushing, close the tank valve, drain valves, and faucets. You can now fill the tank with potable water, and the system is ready to use. The drain plumbing is very similar to that used in your home. The system is trapped and vented to prevent waste gases from backing up into the RV.
Plumbing Systems and Holding Tanks Draining the Holding Tanks The holding tanks terminate in a valve arrangement that permits draining each tank separately. The valves are called knife valves. A blade closes the opening in the sewer drain pipes. The blade is connected to a T-handle and cable assembly mounted in the utility compartment. Pull the T-handle to release the contents of the tank(s).
['------- Plumbing Systems and Holding Tanks 6. Remove the sewer hose and cap the outlet. 7. Rinse out the sewer hose with fresh water and remove the sewer hose from the dump station. 8. Replace sewer or dump station covers. CAUTION The sewer drain valve must be open when using the black tank flush inlet. Gray Holding Tank Dumping allow the water to run for approximately three minutes to flush tank. 3. Turn off water supply to garden hose. 4.
------ Plumbing Systems and Holding Tanks • Keep the black water tank knife valve closed. Fill tank to at least 'I.-full before draining. Be sure to cover the tank bottom with water after draining. • Use only toilet tissue formulated for use in septic tank or RV sanitation systems. • Keep both knife valves closed and locked, and the drain cap tightly in place when using the system on the road. • Use only cleaners that are approved for use in septic tank or RV sanitation systems.
Plumbing Systems and Holding Yanks WATER PUMP SWITCH SPRAY NOZZLE lV/CABLE TELEPHONE CONNECTIONS ELECTRIC CORD STORAGE BLACK WATER KNIFE VALVE BYPASS VALVE HOT & COLD VALVES FOR OUTDOOR SHOWER DRAIN COLD WATER GRAY WATER KNIFE VALVE SEWER HOSE Utility Compartment (detail varies depending on product) 07-8
ELECTRICAL SYSTEMS Your motor home is equipped with three electrical systems: the chassis 12-volt system the Fleetwood 12-volt house system the 120-voltAC system. They operate together to give you electrical power for many different situations. CAUTION Always replace bulbs and fuses with equivalent types. The type is marked on the bulb or fuse.
Electrical Systems These circuits isolate selected electrical systems from either the chassis or the house batteries. Activating the relay(s) will prevent battery discharge which may occur over extended storage periods. During normal use of your motor home the relays must always be in the "on" position. If you plan to store the motor home for an extended period, press the disconnect switch/es to OFF. Remember to press the switch/es to ON when you take the motor home out of storage. .
Electrical Systems • Check and adjust the electrolyte level before charging. Fill each cell to the indicator with distilled water. • Always remove all vent caps before charging the battery. • Do not charge the battelY at a rate that causes the electrolyte to spew out. • In cold temperature storage conditions, batteries may freeze if not properly charged. A. WARNING Remove rings, metal watchbands, and other metal jewelry before working around a battery. Use caution when using metal tools.
Electrical Systems A. WARNING Do not operate the 120-volt electrical system without a proper ground. Electrocution or severe electrical shock could result. A. CAUTION Switch off the 50-amp main breakers located in the 120-volt AC load center (breaker panel) before you insert or remove the 50-amp power plug. Be sure to insert or remove the plug straight into or out of the receptacle. The shore cord power plug should make a snug connection to the shore cord receptacle to avoid over-heating.
1-.--- Electrical Systems Generator Fuel Supply Fuel for the gasoline or diesel generator is taken from the main fuel tank through a special feeder tube which is higher in the tank than the feeder tube to the motor home engine,. This arrangement prevents the generator from running the motor home fuel tank dry. LP Generator (If Equipped) Fuel is provided from a dedicated LP gas tank. Generator Operations To start the generator: 1. Press generator remote switch until generator is running. 2.
Electrical Systems A WARNING Do not modify the generator installation or exhaust system in anyway. Do not use the generator as an emergency power source to a general residential or industrial utility line. This is illegal and may cause shock or electrocution to power line utility personnel attempting to repair power lines. A WARNING Do not block the generator ventilating air inlets or outlets. The engine requires a constant supply of cooling air.
1-.--,Electrical Systems circuit breakers and fuses to intenupt current flow if a circuit is overloaded. 1.l20-volt House Electrical - This electrical panel is located under the refrigerator. This panel is very similar to a residential panel with resettable breakers. 2. Fleetwood Automotive I2-volt System This panel is located on the driver's side under the hood. This electrical center contains battery disconnect systems, entry step, fog light, and some other automotive circuitly.
1== This page intentionally blank.
II LP GAS SYSTEM Liquefied petroleum (LP) gas is available from an approved storage container to operate your range, oven, furnace and water heater, and as an alternate energy source for some refrigerators. With proper handling precautions, LP gas is safe and provides modem conveniences wherever you travel. LP gas is stored as a liquid under pressure and vaporizes under the control of a pressure regulator. A typical LP gas tank installation is illustrated below.
I-~~ ~ LP Gas System A WARNING 7. Turn off LP gas main valve before filling LP gas container or entering an LP gas bulk plant or motor fuel service station. Turn off all pilot lights and appliances individually before refueling of motor fuel tanks andlor LP gas containers. When not individually turned off, automatic ignition appliances may continue to spark when LP gas is turned off at the container. S. Do not fill LP gas containers to more than SO% capacity.
1--LP Gas System USING LP GAS SYSTEM AT LOW TEMPERATURES LP GAS SYSTEM CHECK Your LP gas system will function at low temperatures, provided the system components are kept at a temperature above the vapor point of the LP gas. Ask your LP gas supplier or your motor home dealer for information on product blends available in your area and the areas in which you will be traveling.
1--f--- LP Gas System 5. Lightly fan the area around the detector/ alarm to insure complete dispersion of the gas from the lighter. and to prevent another sounding of the alarm. 6. A silence button allows you to temporarily quiet the alarm for 60 seconds after it has been set off or after testing. 7. If the alarm does not sound during a test or if the green indicator light is not visible, see your dealer or an authorized Fleetwood Service Center.
APPLIANCES The appliances installed in your motor home are tested and listed, and comply with standards established by these organizations. All appliances are covered by Fleetwood's OWfWrcare Warranty program. Each appliance is also warranted by its manufacturer. .II NOTE I The valve is usually located in an exterior luggage compartment near the water pump. Consult with your dealer for the location for your paIticular unit. To bypass the water heater, tum the lever valve vertical.
Appliances The fumace will not operate properly if your stored personal items block the free flow of air at the registers or the retum air to the fumace. Storage under cabinets should be done carefully so as to not clUsh or damage any fumace ducting. Smoke and fumes created as a result of bruning off manufacturing compounds are sometimes present the first time the fumace is used.
1---Appliances Experience has shown that some RV parks may experience reduced power (low voltage) on days with high heat or humidity, commonly referred to as a "brown out." This condition may result in the air conditioner circuit breaker tripping in your power distribution center. This protects your air conditioner motor from damage and is necessary during low voltage conditions. This breaker tripping is sometimes perceived as a fault in your motor home, but it is a necessary "safety valve.
Appliances TV Antenna Operation A. WARNING Do not raise antenna near overhead electric wires as contact may cause serious injury. SATELLITE DISH ANTENNA (If Equipped) The roof-mounted satellite dish antenna is designed for reception of digital satellite television signals. Before traveling, remember to lower the antenna and secure it to prevent damage to the antenna, motor home roof, or objects in the path of the antenna, such as overhead wires. Do not travel with the antenna raised.
I--~- MAINTENANCE Your motor home has been designed to provide you with many years of use with a minimum amount of maintenance. This section will familiarize you with the areas of your motor home that require scheduled care. Time spent taking care of your motor home on a regular basis will pay for itself in extended service and will help protect your investment.
,-1--.. Maintenance Exterior Graphics Care The pressure sensitive graphics installed on the exterior surfaces of your motor home require little maintenance and should be treated similarly to a painted surface. Here are some guidelines to help you keep your exterior graphics looking like new. 1. Wash your graphics with any mild car wash soap solution. Be sure to rinse thoroughly. 2. Keep high-pressure wash nozzles at least 1'/2 feet from the edge of the graphics.
Maintenance ure to inspect and maintain the roof, vents, TV/satellite antenna and molding seals may affect your warranty coverage. The adhesives and sealants used in the construction of your motor home were developed to remain waterproof under sustained effects of weather and vibration. However, even the finest materials will eventually dry out and lose their effectiveness.
Maintenance Solid Surface Top Care (If Equipped) The counter top is constructed of a solid surface material that requires little care. Routine care involves wiping the surface with a damp cloth to remove water marks. For stains, wipe with soapy water or ammonia-based cleaners. Remove stub-. born stains on the "matte/satin" finish with an abrasive cleanser. Laminate Top Care (If Equipped) For cleaning laminate surfaces, uses mild dishwashing liquid with warm water.
1---Maintenance sions. Therefore, keep the floor clean and use exterior walk off mats at the entry door, and: o Immediately blot up spills or spots with a damp cloth. o Periodically clean the floor with Anderson Quick Kleen. Follow the instmctions on the container.
Maintenance MAINTENANCE GUIDELINE While many RV owner's use their RV for weekend and vacation travel, others may use their RV full-time. Full-time use of an RV can considerably affect its condition as well as maintenance requirements. As long as you are not full-timing or traveling under several climate conditions, the normal maintenance guidelines that are outlined in your Fleetwood Owner's Manual will ensure your RV will provide you many years of enjoyable use.
1----,--Maintenance A B c • Wash .exterior Wax exterior • Lubricate TV antenna Check all exterior sealants, around windows, doors, sidewall seams, windshield, lamps, all exterior openings and roof components. Re-seal If necessary. .... Inspect and clean fuel-fired appliance vents: Water heater, refrigerator, furnace. • Inspect and clean water pump filter. E , F .... • • .... Lubricate and adjust exterior locks, hinges, roof vents, window mechanisms, etc.
\-- ,-- This page intentionally blank.
STORAGE STORAGE CHECKLISTS The following checklists will help you perform the steps necessary to prepare your motor home for storage. Use the checklist that applies to the storage conditions you anticipate. These checklists do not include every detail required, and you may want to expand them to suit your needs. Contact your dealer for additional suggestions suitable to your climate and storage conditions, particularly extremes of hot and cold. Short-Term Storage (Less Than 60 Days) 1.
1---- ~ Storage Long-Term Storage (Over 60 Days) 1. Perform all steps as required for short-term storage. 2. Run chassis engine to normal operating temperature. Operate automotive air conditioner(s) to lubricate compressor seals. Drain engine oil, replace filter, refill engine with fresh oil. 3. Remove windshield wiper blades and store inside the motor home. 4. Charge and remove both the chassis and house battery(ies). Store in a cool, dry place, and check the charge and water level every 30 days.
1-.-Storage 3. Winterize the LP gas system. Your LP gas dealer or service station will perform this for you. 4. Winterize all appliances as outlined in the individual operator's manuals. 5. Remove snow accumulations as often as possible. Water System Winterizing Read this section completely before performing winterization. CAUTION Draining the water system alone will not provide adequate cold weather protection.
1--~ Storage 19. Pour one cup of antifreeze solution down each drain. 20. Install all protective caps: Water tank fill City water inlet cap Waste tank drain outlet cap 21. If your refrigerator is equipped with an ice maker, winterize it as follows: 1. Shut off the water supply valve to the ice maker. 2. Place a shallow pan under the water solenoid valve. 3. Remove the inlet fitting to the ice maker water solenoid valve. Drain the water from the supply line. 4.
1__ - . .c_ Storage 13. Operate all faucets and fixtures in the fresh water system. Check for leaks at all joints and fittings. Repair if necessary making sure the water heater bypass is open. 14. Check operation of 12-volt circuit breakers and inspect fuses. Replace as necessary. 15. Operate all 12-volt lights and accessories. 16. Install new batteries in battery-operated devices. Check operator's manual for each device for any additional requirements. 17.
This page intentionally blank.
1----.- GLOSSARY AC Inverter - An electronic device that changes 12-volt DC energy from the batteries to 120volt 60-cycle, AC energy to operate microwave ovens, TVs, VCRs, or other appliances that require 120-volt 60-cycle power. Belted Seating Positions - These are seats with seat belts. Anyone riding in the motor home must use one of these seats any time the motor home is in motion. Black Water Tank - The water tank in your plumbing system that is designed to contain waste water from the toilet ONLY.
Glossary GVWR (Gross Vehicle Weight Rating) - Is the maximum permissible weight of this fully loaded motor home. The GVWR is equal to or greater than the sum of the Unloaded Vehicle Weight plus the Cargo Carrying Capacity. Hitch Rating - Means the maximum allowable weight of a towed trailer or towed vehicle. The GCWR of the motor home must never be exceeded, even if the weight of the towed trailer or towed vehicle is less than the hitch rating.
Notes
-----1 Notes -
