Installation Instructions Barcode Dock Mount w w w . a m i c o .
Preface IMPORTANT, PLEASE READ CAREFULLY Thank you for your purchase with Amico Accessories Inc. This unit is designed for long lasting performance, provided that the end user complies with assembly and maintenance procedures. This Instruction Manual is your guide to ensure that you get the best performance out of the equipment. Amico Accessories Inc.
Contents Section 1: Product Specifications Features 4 4 Section 2: Installation Preparation Installation, Tools and Part Requirements 5 5 Section 3: Installation on Mounting Platform Mounting onto Equipment Rail Mounting onto LCD VESA Plate 6 6 6 Section 4: Device Installation Mounting of Devices 7 7-10 Section 5: Adjustments Adjustment Procedure 11 11 Section 6: Maintenance and Troubleshooting Troubleshooting Preventative Maintenance Cleaning 12 12 12 12 www.amico.
SECTION 1: Product Specifications Features • Can be mounted onto rail against wall or behind LCD monitor • Accommodates a variety of barcode scanner bases and has been tested with: • Code Reader CR2600 and other scanners using the CRA-A101 or CRA-A104 charging base • Honeywell 3820, 4620, 4820, 5620 and other scanners using the Honeywell 2020 charging base • Honeywell Xenon 19xx series and other scanners using the CCB01-010BT charging base • Honeywell Granit 19xx series and other scanners using the CCB02-10
SECTION 2: Installation Preparation Tools Installation, Tools and Part Requirements • No. 2 Phillips head screwdriver (not provided) 1/8" HEX key No.
SECTION 3: Installation on Mounting Platform Mounting onto Equipment Rail: 1. Refer to mounting instructions provided with equipment rail for BARCDHLD2-(M/F/A/E25/R125/RMC/V/D/G/S). Mounting onto LCD VESA Plate: 1. For BARCDHLD2-LCD, slide X-MON-SHELF-ARM to desired position and tighten two H-HNUT-1420. Insert and tighten two H-1420-LNUT-NYL to lock X-MON-SHELF-ARM in place as seen in Figure 1. 2.
SECTION 4: Device Installation Mounting of Devices 1. For BARCDHLD2-(M/F/A/E25/R125/RMC/V/D/G/S): Before mounting product onto mounting platform, determine the mounting pattern on the barcode scanner base to be mounted. If the barcode scanner base is too large to mount onto X-BRCDHLD-LBKT, proceed to step 2 for the installation of the secondary plate. 2.
SECTION 4: Device Installation Mounting of Devices 1. For the BARCDHLD2-LCD: Determine the mounting pattern on the barcode scanner base to be mounted. If the barcode scanner base is too large to mount onto X-BRCDHLD-LBKT, proceed to step 2 for the installation of the secondary plate. 2.
SECTION 4: Device Installation Mounting of Devices Determine the preferred orientation of the barcode charging base and refer to the below illustrations for mounting. NOTE: The illustrations shown may not portray the configuration purchased. Use this as a reference to pair hardware and mounting hole pattern with respective barcode scanner base (not provided).
SECTION 4: Device Installation Mounting of Devices Determine the preferred orientation of the barcode charging base and refer to the below illustrations for mounting. NOTE: The illustrations shown may not portray the configuration purchased. Use this as a reference to pair hardware and mounting hole pattern with respective barcode scanner base (not provided). Figure 15 Barcode charging base with three FIGURE 15 holes, such as Honeywell CCB02-100BT for Honeywell Granit 1910i, 1911i.
SECTION 5: Adjustments Adjustment Procedure 1 1. To adjust BARCDHLD2-LCD, remove two H-CAP-14-W, two H-1420-LNUT-NYL and loosen two H-HNUT-1420. 2. Slide X-MON-SHELF-ARM to desired location and re-tighten two H-HNUT1420 and H-1420-LNUT-NYL.
SECTION 6: Maintenance and Troubleshooting Troubleshooting Symptom Solution There is unwanted movement between the barcode scanner charging base and BARCDHLD2-_ , or between BARCDHLD2-_ and the mounting platform Ensure all screws are tight Preventative Maintenance It is recommended that once every 3 months, the barcode scanner base is removed from the product and you ensure that all screws are tightened.
Accessories Warranty Policy Amico Accessories Inc. warrants all mounting accessories to be free from defects in material and workmanship for a period of twelve (12) months from the date of shipment. Within this period Amico Accessories Inc. will repair or replace any part which is proven to be defective. Amico Accessories Inc. will warrant its materials to be free from defect for an additional period of four (4) years, five (5) years from the date of shipment. Within this period, Amico Accessories Inc.
Notes 14 Amico Accessories Inc.
www.amico.com Amico Accessories Inc. | www.amico.com 85 Fulton Way, Richmond Hill Ontario, L4B 2N4, Canada 71 East Industry Court, Deer Park NY 11729, U.S.A. Toll Free Tel: 1.877.264.2697 Toll Free Fax: 1.866.440.4986 Tel: 905.763.7778 Fax: 905.763.8587 Email: info@amico.com AA-IM-BARCDHLD 09.18.
