Specifications

Subdued Ringing
Refer to the discussion titled Ringing.
System Alarm Reports
The programmer can arrange the system to report
alarm and status conditions to a particular station or
stations that he or she has enabled to receive them.
The alarm receiving station must be an LCD
speakerphone. When a station is enabled to receive
alarms, its user can take appropriate action to cause
the alarm codes to be presented on the LCD display.
A programmer must use both system and station class
of service programming to enable this feature.
System Speed Dial
Refer to the discussion titled Automatic Dialing.
Tandem Attendant
When the programmer uses system class of service
programming to enable the tandem attendant feature,
a recall from an unanswered call transfer or a timed
hold recall will ring at the normal attendant station
(station 10) that set the transfer or hold condition, and
also ring at the tandem attendant station (station 12).
TAP (Flash/Recall)
If the host system provides custom calling features via
a hookflash signal, the programmer should program
the system so that the TAP button will generate a
“flash” signal when a user presses it. If custom calling
features are not available to digital telephone system
users, the programmer should program the TAP
button to function as a positive disconnect, dial tone
recall button. The flash and recall features are
mutually exclusive. The programmer uses the system
class of service programming procedures to set the
flash or recall TAP time.
Tenant Service
Refer to the discussion titled SquareIVon-Square
Configuration.
Timed Hold Recall
Refer to the discussion titled Ho/d,
Toll Restriction
Default Toll Restriction
The system defaults two toll restriction tables with
pre-programmed values and pre-assigned to all lines.
The programmer needs only to assign these tables to
the stations by programming action to put them into
effect. He or she can use the toll restriction table
configuration class of service programming to
reprogram the defaulted tables wlth different
information as needed.
Description Of System Features
IM166-107
Flexible Toll Restriction
A system programmer can configure system toll call
restriction to prohibit some or all stations from calling a
wide range of number combinations. The restricted
numbers are specified on up to 16 tables. The system
assigns several broad-range values to two of these
tables, and assigns the tables to all lines as a default
condition. The programmer needs only to enable the
default tables on a per station basis to activate the
default toll restriction.
In general, toll restriction works as follows:
The programmable tables of restricted numbers can
contain up to four entries and each entry can contain
up to 16 digits.
A programmer programs each table of restricted
numbers to be an “allow” table or a “deny” table with
entries in an “allow” table overriding entries in a “deny”
table. This arrangement allows the programmer to
enable exceptions to toll restriction. For example, he
or she can arrange the table entries so that the system
allows the dialing of
1-800~xxx-m
numbers even
though it denies the dialing of all
I-xxx-xxx-xxxx
numbers. A programmer can store a “match anything”
symbol (#) to represent any digit from 0 to 9 in the
individual entries thus providing him or her with a
broad range of number combinations to choose from.
The programmer can individually assign the
programmed toll restriction tables to each appropriate
station and line. Therefore, when an outside call is
dialed, the system examines the dialed number and
makes a comparison between it and the toll restriction
tables. Any tables that the programmer assigned to
BOTH the station being used and the selected line
determine the restrictions to be imposed; It should be
noted that the system will automatically disconnect a
line from a station if its user dials a restricted number
on a restricted line from a restricted station.
Night Mode Toll Restriction
A programmer can assign toll restriction tables to any
or all stations in the system that will only take effect
when the system is in the night transfer (of ringing)
mode. These toll tables replace any that he or she
may have assigned to the station for normal, or day
mode, operation. For example: a programmer can
arrange for a station that has no other toll restriction
table assignment to receive a toll restriction table
which will restrict everything but local calls and will
only take effect when the system is placed in the night
transfer (of ringing) mode. Therefore, even though
users can make toll calls from this station during
daytime operation, they can make no toll calls from it
when the attendant programs the system for nighttime
operation using the night transfer of ringing feature.
NOTE: Do
not confuse this night mode to// restriction
table assignment with the night transfer (of
ringing) feature.
2-24