Specifications
IM166-107
System Programming
.
ExecuMaWEloquence
Intetface
Configuration
The digital telephone system supports the use of the ExecuMail voice mail equipment connected to the system’s
station ports through the Comdial ATI-D analog terminal interface device. The ATI-D is a multipurpose
on-premise accessory that has dual circuits to allow a e-port voice mail system to interface to two digital station
ports. Two ATI-D devices are needed to interface 4-port voice mail systems. Refer to Comdial publication
lMl89-037, installation instructions For The Analog Terminal interface (AT/-D) for complete details for using the
ATI-D to interface between the digital telephone system and the voice mail system. In addition, the system
supports the Eloquence
VI/VIA
series of voice mail equiptment connected directly to a station port.
Along with the required programming task of identifying the station ports as voice mail ports, there are several
other programming considerations associated with voice mail operation that are optional for use as needed.
0
To make a record of the programming configuration, mark the desired requirements in the analog terminal
interface records chart found at the end of Chapter 4.
0
To make the programming selections, dial the feature code and then dial the configuration code (or press the
programming button where appropriate).
NOTE:
A lighted LED next to the programming button for the selection indicates the current configuration.
When a
single
button
provides
a toggle (on/off) action, the lighted LED indicates the active feature.
0
The first step in any programming sequence is to enter the base level. Once in this mode, you can dial the
feature code for any desired configuration.
Enter the base level with the following procedure: press
ITCM
then
dial
X#
7 4 6
5.
The last step is to press the
SPKR
button to end the programming procedure and return the
system to normal operation.
ExecuMail/Eloquence Interface
Configuration
-
Required Feature
Voice Mail Port
To assign voice mail ports,
When you connect the voice mail system to 1. Dial 53.
“STATION FEATURES”
a station port through the ATI-D, you must 2. Dial 32.
“VOICE MAIL PORT
*
use this programming feature to enable the 3. Select station ports (LED On = Selected):
station port as a voice mail port.
-
Station 10
-
57 = dial
10
-
57
or press
Cl 0
-
C57.
NOTE:
The system automatically disables
4. Dial
+N
for next feature.
this feature if you replace the ATI-D
-OR-
with a digital multiline telephone at
Dial
+K
*
for configuration mode.
the programmed station port. You
To change setting, repeat procedure and make different selection.
must manually disable the station
Poti
as
a
Voice
mai
Poti
when
YOU
use it to interface a mode/ 2500
To assign direct ringing for automatic attendant operation,
1. Dial 54.
“STAILINE
CONFIG”
telephone through the A TI-D.
2. Dial 1.
“DIRECT RING
”
With its automatic attendant feature, the
voice mail system automatically answers
3. Select line ports for direct ringing:
any line that is ringing at a voice mail port.
Line port 1-14 = Dial 0 -14 or press
Al
-
A14,
As a default, the system automatically
Line port 15,16 = Dial
15,16
or press
Bl,
B2,
enables ringing line preference for any port
Line port 17-24 = Dial
17-24
or press
HOLD
then press
Al
-
A8)
that you have identified as a voice mail
4. Dial
#
when all line ports are selected.
port. You must choose a ringing
5. Select station ports (LED On = Selected):
assignment for the lines that you have
-
Station
lo-
57: Dial
10
-
57
or press
Cl 0
-
C57.
assigned to the voice mail ports before the
6. Dial
t
when all station ports are selected.
voice mail system can provide the
7. Dial
+R
+K
+N
for configuration mode.
automatic attendant feature.
To change setting, repeat procedure and make different selection.
continued on next page . . .
4-55