Specifications
System Programming
IMl66-107
Account Code (With Positive Forced Verification) Configuration
The digital telephone system uses account codes to identify calls by category, or by any other desired
grouping,
so that it can record the cost of the calls by that category or grouping. The account code can be either verified or
not verified by the system plus the system can either force the users to use the account codes or make their use
optional. When you enable account code verification, the system compares the account code entered by a
station user with the account entries that you have programmed.
If the system does not find a match and the
account code entry is optional, the system sounds an error tone through the telephone but does not prevent
dialing; however, if forced entry is enabled, the system prevents further dialing until the user enters a matching
account code
D
To make a record of the programming configuration, mark the desired requirements in the account code
records chart found at the end of Chapter 4.
B
To make the programming selections, dial the feature code and then dial the configuration code (or press the
programming button where appropriate).
VOTE:
A lighted
LED
neti
to the programming
button for the selection indicates the current configuration. When
a
sing/e
button
provides
a toggle (on/off) action,
the lighted LED indicates the active feature.
D
The first step in
any
programming sequence is to enter the base level.
Once in this mode, you can dial the
feature code for any desired configuration. Enter the base level with the following procedure: press ITCM then
dial
t#
7 4 6
#+.
The last step is to press the
SPKR
button to end the programming procedure and return the
system to normal operation.
’
.
lccount Codes
(Feature Enabled Or
Iisabled)
Jse this procedure to enable or disable the
xcount
code feature for the system.
kcount
Codes
(Forced Or Optional Entry)
Jse this programming procedure to
arrange for the system to either force the
Jser’s to enter account codes before they
:an make calls or to make the enter of
account codes an optional condition.
Emergency Numbers:
Even if you arrange
‘or the system to force account code
entries, users can always dial emergency
lumbers without first entering an account
:ode. Use this programming feature to
enter up to three emergency numbers.
Each number can be a minimum of
1
digit
and
a maximum of 12 digits.
1. Dial 75.
“SMDA PROGRAMMING
2. Dial 0 7.
“XXXXXXXXACCOUNT
3. Press
Al
to toggle the feature on or off (LED On = Enabled).
-OR-
4. Dial
1
to enable account codes.
“ENABLE ACCOUNT
Dial 2 to disable account codes.
“DISABLEACCOUNT
5. Dial
#G
*
for configuration mode.
To change setting, repeat procedure and make opposite selection
1. Dial 53.
“STATION FEATURES’
2. Dial 35.
“FORCEACCT.
CODE” .
3. Press
Al
for forced account codes on all stations
-OR-
Press A2 for optional account codes on all stations
4. Select station ports to be exempted. (If forced, these will be
optional. If optional, these will be forced).
-DiallO-57orpressClO-C57
(LED On = Feature Enabled, Off = Exempted).
5. Dial
t
t
for configuration mode.
To change setting, repeat procedure and make opposite selection
To specify emergency numbers,
1. Dial 75.
‘SMDA PROGRAMMING”
2. Dial 16.
“SET EMER. NUMBER”
3. Dial emergency number (up to 12 digits) then dial #.
4. To enter another emergency number, repeat step 3.
5. Dial
S&K
for configuration mode.
To clear emergency numbers,
1. Dial 75.
“STATION FEATURES
2. Dial 17.
“CLR EMER. NUMBER”
3. Dial number to be cleared (up to 12 digits) then dial #.
4.
T
O
clear another number, repeat step 3.
5. Dial
t
+K
for configuration mode.
Press SPKR to end.
I
4-44