Specifications
IM166-107
System Programing
Station Configuration
-
Miscellaneous Features
-
continued
Press ITCM
+++#746%
Flexible Station Numbering
The
system supports a flexible station
lumbering plan for calling individual
stations and departments. You can
)rogram each station port to respond to the
dialing of any available number between 10
and
7999; however, the system will not
allow you to assign the same dialing code
2s
both a station extension number and a
department access code, nor will the
system .allow you to assign an extension
qumber or access code conflict such as 15
snd
1500.
1. Dial 52.
“ACCESS CODE
”
2. Dial
1
to assign extension number “ASSIGN EXT. NUM.
”
3. Select station port: “EXT.
XXXX
*
-
Station 10
-
57 = Dial
10
-
57
or press
Cl0
-
C57.
4. Dial new extension number.
“En.
xxxx
YYYY
Ii
NOTE: Extension number can be max. of four digits.
If
less
than four digits, leading zeros must be dialed before
number. Example: For ext. no. 15, dial 0075).
5. Select next station number and assign extension number.
-OR-
Dial
+K
for configuration mode.
To change setting, repeat procedure and make opposite selection,
Zroup
Call Pickup
if
a call rings to any station in a
Drearranged group, a user at another
station in that group can dial a group pickup
zode and answer the call. Assign the
stations to call pickup groups using this
Drocedure.
Headset Interface
When employing DigiTech (product code
7700s rev. H and earlier) and Americom
[product code 7016s all revs.) LCD
speakerphones, you must use this
Drogramming procedure to enable a station
z~ort
to allow headset operation.
When employing impact (product code
31248 all rev.) and DigiTech (product
zodes 7700s rev I and later) LCD
speakerphones, either you or the individual
station user must program a headset button
at his or her LCD speakerphone to activate
the headset operation.
NOTE: The system delivers subdued
off-hook voice announcements
(SOHVA) to the headset. Because
a headset exhibits a coupling effect
between the earpiece and
microphone, it may allow the
outside party to hear the SOHVA
message. You should inform the
user of this possibility.
1. Dial 53.
2. Dial 16.
3. Dial 0 for no group
-OR-
‘STATION FEA TlJRES”
“GRP.
CALL PICKUP”
4. Dial
1
-
4 for group 1
-
4.
%ROUPX
’
5. Select station ports (LED On = Feature Assigned):
-
Station 10
-
57: Dial
10
-
57
or press
Cl0
-
C57.
6. Dial
f
for next group
-OR-
Dial
G#
+R
for next station feature.
-OR-
Dial
*
*
+K
for configuration mode.
To remove station from call pickup group, assign it to group 0.
To arrange for headset operation as a class of service,
1. Dial 53.
“STATION FEATURES”
2. Dial 13.
“HEADSETMODE
”
’
3. Select station ports (LED On = Feature Assigned):
-
Station 10
-
57: Dial
10
-
57
or press
Cl0
-
C57.
4. Dial
+R
for next station feature.
-OR-
Dial
+K
+K
for configuration mode.
To change setting, repeat procedure and make opposite selection.
To arrange for headset operation at a user’s telephone,
1. Press
ITCM
at the user’s telephone.
2.Dial+K+l.
3. Select button to be programmed:
-
Press Al
-
A14,
Bl
-
810.
4. Dial 94.
5. Press
SPKR
to end.
I
Press SPKR to end.
4-29