GA-8IEXW P4 Titan 533 Motherboard USER’S MANUAL Pentium® 4 P rocessor Motherboard Rev.
English GA-8IEXW Motherboard Table of Content Item Checklist .................................................................................4 WARNING! .......................................................................................4 Chapter 1 Introduction ......................................................................5 Features Summary................................................................................................ 5 GA-8IEXW Motherboard Layout ..............................
Chapter 4 Technical Reference ........................................................ 50 Block Diagram ..................................................................................................... 50 Chapter 5 Appendix ........................................................................
English GA-8IEXW Motherboard Item Checklist þ þ þ þ þ þ The GA-8IEXW motherboard IDE (ATA100 ) cable x 1 / Floppy cable x 1 IDE (ATA133 )cable x 2 CD for motherboard driver & utility GA-8IEXW user’s manual I/O Shield WARNING! Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To protect them against damage from static electricity, y ou should follow some precautions whenever you work on your computer. 1. Unplug your computer w hen w orking on the inside. 2.
Introduction Chapter 1 Introduction Features Summary Form Factor Motherboard — 30.6cm x 24.4cm ATX size form factor, 4 layers PCB. — GA-8IEXW Motherboard: CPU — Socket 478 for Intel® Micro FC-PGA2 Pentium® 4 processor — Intel Pentium® 4 533MHz/400MHz FSB — Support Intel ® Pentium ® 4 (Northwood, 0.
English GA-8IEXW Motherboard Hardware Monitor — — — — On-Board Sound — CPU/Power/System Fan Revolution Detect CPU/Power/System Fan Control CPU Overheat Warning System Voltage Detect Realtek ALC650 CODEC On-Board RAID — — — — — — — — On-Board LAN On-Board USB 2.0 PS/2 Connector BIOS — — — — — Onbard Promise PDC20276 Supports data striping (RAID 0) or mirroring (RAID 1) Supports concurrent dual ATA133 IDE controller operation Support ATAPI mode for CD ROM, DVD ROM ..etc.
Hardware Installation Process GA-8IEXW Motherboard Layout VGA AGP Slot VGA_EN LINE_IN GAME LAN PCI 1 SPDIF AC97 AUX_IN W986432DH-6 CD_IN USB ATI Rage XL COM MIC_IN LINE_OUT LPT1 KB_MS AUX_12V NB_FAN CPU IDE 3 IDE 4 F_PANEL CLR_CMOS IDE 2 IDE 1 BATTERY BIOS DDR1 DDR 2 DDR 3 CI Model_SW1 ATX FDD PWR_FAN SYS_FAN -7 - IR CPU_FAN PCI 2 PCI 3 SOCKET478 SOCKET478 ICH4 PDC20276 F_USB1/3 F_USB2/4 PCI 4 PCI 5 WOR Intel 845E
English GA-8IEXW Motherboard Chapter 2 Hardware Installation Process To set up your computer, you must complete the following steps: Step 1- Install the Centr al Processing Unit ( CPU) Step 2- Install memory modules Step 3- Install expansion cards Step 4- Connect ribbon cables, cabinet w ires, and power supply Step 5- Setup BIOS softw are Step 6- Install supporting software tools Step4 Step3 Step1 Step 4 Step 4 Step4 -8 - Step 4 Step 2
Hardware Installation Process Step 1: Install the Central Processing Unit (CPU) Pin1 indicator Pin1indicator CPU Top View CPU Bottom View Socket Actuation Lever Pin1 indicator 1. Pull up the CPU socket lever and up to 90-degree angle. 2. Locate Pin 1 in the socket and look for a (golden) cut edge on the CPU upper corner. Then insert the CPU into the socket. 3. Press down the CPU socket lever and finish CPU installation. M Please make sure the CPU type is supported by the motherboard.
English GA-8IEXW Motherboard Step 1-2:CPU Heat Sink Installation 2. Make sure the CPU fan is plugged to the CPU fan connector. Install complete. 1. Hook one end of the cooler bracket to the CPU socket first. Hook the other end of the cooler bracket to the CPU socket. M Please use Intel® approved cooling fan. M We recommend you to apply the thermal paste to provide better heat conduction between the CPU and heatsink.
Hardware Installation Process Step 2: Install memory modules The motherboard has 3 dual inline memory module (DIMM) sockets, but it can only support a maximum of 4 banks DDR memory. DDR socket 1 uses 2 banks, DDR socket 2& 3 share the remaining 2 banks. Please refer to the following tables for possible memory configurations supported. The BIOS will automatically detects memory type and size. To install the memory module, just push it vertically into the DIMM Slot .
English GA-8IEXW Motherboard DDR 1. The DIMM slot has a notch, so the DIMM memory module can only fit in one direction. 2. Insert the DIMM memory module verticallyinto the DIMM slots. Then push it down. 3. Close the plastic clip at both edges of theDIMM slots to lock the DIMM module. M Reverse the installation processes when you want to remove the DIMM module.
Hardware Installation Process Step 3: Install expansion cards 1. Read the related expansion card’s instruction document before install the expansion card into the computer. 2. Remove your server’s chassis cover, necessary screws and slot bracket from the computer. 3. Press the expansion card firmly into expansion slot in motherboard. 4. Be sure the metal contacts on the card are indeed seated in the slot. 5. Replace the screw to secure the slot bracket of the expansion card. 6.
English GA-8IEXW Motherboard Step 4: Connect ribbon cables, cabinet wires, and power supply Step 4-1 : I/O Back Panel Introduction u v w y x u PS/2 Keyboard and PS/2 Mouse Connector PS/2 Mouse Connector (6 pin Female) ØThis connector supports standard P S/2 keyboard and PS/2 mouse. PS/2 K eyboard Connector (6 pin Female) v Parallel Port and Serial Ports (COMA/COMB) Parallel Port (25 pin Female) ØThis connector supports 1 standard COM port , 1 VGA port and 1 Parallel port.
Hardware Installation Process w Game /MIDI Ports ØThis connector supports joystick, M IDI keyboard and other relate audio devices. Joystick/ MIDI (15 pin Female) x Audio Connectors Line Out 1 MIC In Line In (Line Out 2) Ø After install onboard audio driver, you may connect speaker to Line Out jack, micro phone to MIC In jack. Device like C D-ROM , walkman etc can be connected to Line-In jack.
English GA-8IEXW Motherboard Step 4-2 :Connectors & Jumper Setting Introduction T U X V Y S R W A Q G F P M O L K J N I B H E C D A) CPU_FAN N) Model_SW1 B) BATTERY O) IDE4 C) ATX P) F_USB1/F_USB3 D) IR/CIR Q) F_USB2/F_USB4 E) FDD R) WOL F) IDE 1 S) VGA_EN G) IDE 2 T) SPDIF H) PWR_FAN U) AUX_IN I) SYS_FAN V) CD_IN J) CI W) SCSI_CON K) CLR_CMOS X) NB_FAN L) F_PANEL Y) AUX_12V M) IDE3 - 16 -
Hardware Installation Process Y ) AUX_12V( +12V Power Connector) 1 3 Ø This connector (ATX +12V) is used only for CPU Core Voltage. +12V +12V GND GND 2 4 A) CPU_FAN (CPU Fan Connector) Sense +12V/Control GND Ø Please note, a proper installation of the CPU cooler is essential to prevent the CPU from running under abnormal condition or damaged by overheating.The CPU fan connector supports Max. current up to 600mA .
Ø Important Notice: Please connect first hard disk to IDE1 and connect CDROM to IDE2. IDE2 1 IDE1 1 M,O) IDE3/IDE4 Connector 1 IDE4 1 IDE3 Important Notice: 1. Please connect first harddisk to IDE1 and connect CDROM to IDE2. 2. If you w ish to use IDE3 and I DE4, please use it in unity with BIOS (either RAID or ATA 133). Then, install the correct driver to have proper operation. For details, please refer to the RAID manual.
Hardware Installation Process R) WOL(Wake on LAN) 1 +5V SB GND Signal T)SPDIF 1 Ø The SPDIF output is capable of providing digital audio to external speakers or com pressed AC3 data to an external Dolby Digital Decoder. U se this feature only when your stereo system has digital output function. VCC SPDIF Out GND SPDIF X) NB _FAN Ø If installed wrong direction, the C hip Fan will not work. Sometimes will damage the Chip 1 Fan.
USBx+ GND 1 Power NC USBy+ USByNC USBXGND GND Ø Be careful with the polarity of the front panel USB connector. Check the pin assignment while you connect the front panel USB cable. P lease contact your nearest dealer for optional front panel USB cable. Q) F_ USB2 / F_USB4(Front USB Connector) USBx+ 1 Power GND NC USBy+ USBy- USBXGND GND NC Ø Be careful with the polarity of the front panel USB connector. Check the pin assignment while you connect the front panel USB cable.
Hardware Installation Process D) IR/CIR (IR/CIR Connectors) NC GND VCC CIRRX NC IRTX GND IRRX NC VCC 1 Ø Make sure the pin 1 on the IR device is aling with pin one connector. To enable the IR/CIR function on the board, you are required to purchase an option IR/ CIR module. For detail information, please contact your autherized Giga-Byte distributor. To use IR function only, please connect IR module to Pin1 to Pin5.
English GA-8IEXW Motherboard N ) Model_SW1 Non-jumper: Logo 1 (Default values) Jumpered: Logo 2 B ) BATTERY (Battery) CAUTION v Danger of explosion if battery is incorrectly replaced. v Replace only with the same or equivalent type recommended by the manufacturer. v Dispose of used batteries according to the manufacturer’s instructions.
Hardware Installation Process L) F_PANEL (2x9 pins connector) H- SPK NC NC SPK RS GN RS G18 1 H+ P- P- P+ PW PW G+ GN PIN REMOVERD H+ HPSPK PP+ PW SPK PW RS RS G+ GGN GN Pin 1: Hard Disk LED power Pin 2: Hard Disk Active LED signal Pin 3: Front panel Green LED signal Pin 4: Front panel speaker signal Pin 5: Front panel power LED signal Pin 7: Front panel power LED power Pin 9: Front panel power button signal Pin 10: Front panel speaker signal Pin 11: Front panel power button signal Pin 12: Fron
GA-8IEXW Motherboard Chapter 3 BIOS Setup BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. ENTERING SETUP Power ON the computer and press immediately will allow you to enter Setup.
BIOS Setup Q-Flash Utility After power on the computer, pressing immediately during POST (Power On Self Test) it will allow you to enter Award BIOS CMOS SETUP, then press to enter Q-Flash utility. If you request detail information for “Q-Flash Utility “, please download the manual from Gigabyte web http://www.gigabyte.com.tw. GETTING HELP Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen.
GA-8IEXW Motherboard Main (For example: BIOS Ver. :F1) Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 1) will appear on the screen. Use arrow keys to select among the items and press to accept or enter the sub-menu. CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Main Adv anced Boot Serv er Security Clk/Voltage Defaults Ex it Date (mm:dd:y y ) Mon.
BIOS Setup C Time The times format is setin , and . The time is calculated base on the 24hour military-time clock. For example, 1 p.m. is 13:00:00. C IDE Primary Master, Slave / Secondary Master, Slave The category identifies the ty pes of hard disk from driv e C to F that has been installed in the computer. There are two types: auto type, and manual type. Manual type is user-definable; Auto type that will automatically detect HDD type.
GA-8IEXW Motherboard C Drive A / Drive B The category identifies the types of floppy disk drive A or drive B that has been installed in the computer. 8None No floppy driv e installed 8360K, 5.25 in. 5.25 inch PC-ty pe standard driv e; 360K by te capacity . 81.2M, 5.25 in. 5.25 inch AT-ty pe high-density driv e; 1.2M by te capacity (3.5 inch w hen 3 Mode is Enabled). 8720K, 3.5 in. 3.5 inch double-sided driv e; 720K by te capacity 81.44M, 3.5 in. 3.5 inch double-sided driv e; 1.44M by te capacity .
BIOS Setup Advanced CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Main Advanced Boot Server Securi t y Cl k/Vol t age Def aul t s Exi t }Adv anced BIOS Feature Item Help }Integrated Peripherals Menu Lev el} }Pow er Management Setup }PnP/PCI Configuration Miscellaneous BIOS Feature...
GA-8IEXW Motherboard C Quick Power On Self Test This category speeds up Power On Self Test (POST) after you power on the computer. Ifit is set to Enable, BIOS will shorten or skip some check items during POST. 8Enabled Enable quick POST. (Default Value) 8Disabled Normal POST. C Boot Up Fl oppy Seek During POST, BIOS will determine the floppy disk drive installed is 40 or 80 tracks. 360 K type is 40 tracks; 720 K, 1.2 M and 1.44 M are all 80 tracks.
BIOS Setup C MPS Version Control For OS This option allows user to set OS Multi Processors version. (Support Multi Processor Specification revision 1.4) Note: Some old MPS OS support 1.1 version only. 81.4 Support MPS Version 1.4 . (Default Value) 81.1 Support MPS Version 1.1.
GA-8IEXW Motherboard Integrated Peripherals CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Adv anced Integrated Peripherals Item Help On-Chip Primary PCI IDE [Enabled] Menu Lev el}} On-Chip Secondary PCI IDE [Enabled] If a hard disk IDE 1 Conductor Cable [Auto] controller card is used, IDE 2 Conductor Cable [Auto] set at Disabled USB Controller [Enabled] USB Key board Support [Disabled] [Enabled] Onboard ATA/RAID Dev ice [Enabled] Enable onboard IDEPORT RAID Controller
BIOS Setup C IDE 1/ 2 Conductor Cable 8Auto Set this functio to auto detect IDE cable ty pe. (Default v alue) 8ATA66/100 Set conductor cable to ATA66/100 8ATA33 Set conductor cable to ATA33 CUSB Controller 8Enabled Enable USB Controller function. (Default v alue) 8Disabled Disable USB Controller function. C USB Keyboard Support 8Enabled Enable USB Key board Support. 8Disabled Disable USB Key board Support. (Default v alue) C USB Mouse Support 8Enabled Enable USB Mouse Support.
GA-8IEXW Motherboard C Onboard Serial Port 1 8Auto BIOS w ill automatically setup the port 1 address. (Default v alue) 83F8/IRQ4 Enable onboard Serial port 1 and set IO address to 3F8. 82F8/IRQ3 Enable onboard Serial port 1 and set IO address to 2F8. 83E8/IRQ4 Enable onboard Serial port 1 and set IO address to 3E8. 82E8/IRQ3 Enable onboard Serial port 1 and set IO address to 2E8. 8Disabled Disable onboard Serial port 1.
BIOS Setup Power Management Setup CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Adv anced Pow er Management Setup ACPI Suspend Ty pe Item Help [Enabled] [S1 POS] Menu Lev el}} Soft-Off by PWR BTTN [Instantt-Off] [User Define] State After Pow er Failure [Auto] Configure our ow n PME Ev ent Wake Up [Auto] pow er management Resume by Alarm [Disabled] feature x Date (of Month) Alarm Ev ery day [Min Sav ing] x Time (hh: mm: ss) Alarm 0:0:0 Minimun pow er Pow er On By Mouse
GA-8IEXW Motherboard C ACPI Suspend Type 8S1 Set suspend type to Power On Suspend under ACPI OS. (Default Value) 8S3 Set suspend ty pe to RAM under ACPI OS. C Soft-off by PWR-BTTN 8Instant-off Press pow er button then Pow er off instantly . (Default v alue) 8Delay 4 Sec. Press pow er button 4 sec to Pow er off. Enter suspend if button is pressed less than 4 sec. C State After Power Failure 8Auto When AC-pow er back to the sy stem, the sy stem w ill return to the Last state before AC-pow er off.
BIOS Setup C Power On By Mouse 8Disabled Disable this function. (Default Value) 8Mouse Click Mose double click to pow er sy stem. C Power On By Keyboard 8Disabled Disable this function. (Default Value) 8Passw ord Enter from 1 to 5 characters to set the Key board Pow er On Passw ord. 8Key board 98 y our sy stem.
GA-8IEXW Motherboard Pnp/PCI Configuration CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Adv anced PnP/PCI Configuration PCI 1/PCI 5 IRQ Assignment [Auto] [Enabled] PCI 2 IRQ Assignment [Auto] PCI 3 IRQ Assignment [Auto] PCI 4 IRQ Assignment [Auto] higf: Mov e Enter: Select +/-/PU/PD: Value F5: Prev ious Values F10: Sav e F7: Optimized Defaults ESC: Ex it F1: General Help F8: Q-Flash Figure 2-4: PnP/PCI Configuration C PCI 1/PCI 5 IRQ Ass ignment 8Auto 83,4,5,7,9.
BIOS Setup Boot CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Main Adv anced Boot Serv er Security Clk/Voltage Defaults Ex it RAID/SCSI Boot Order [RAID, SCSI] Item Help First Boot Dev ice [Floppy ] Menu Lev el} Second Boot Dev ice [CDROM] Select Boot Decice Third Boot Dev ice [HDD] Priority BootUp Num-Lock [On] [Floppy ] Boot to OS2 or DR-DOS [No] Boot from floppy Console Redirection [Disabled] [LS120] 19200 Boot from LS120 Agent Address [Auto] [HDD] Agent
GA-8IEXW Motherboard C BootUp Num-Lock 8On 8Off Key pad is number key s. (Default v alue) Key pad is arrow key s. C Boot to OS2 or DR-DOS 8No Disable this function. (Default Value) 8Yes Select Yes, if y ou are running OS/2 or DR-DOS w ith greater than 64MB of RAM on the sy stem. C Console Redirection 8Disabled Attempt to redirect console w hen key board absent. 8Enabled Attempt to redirect console v ia COM port. (Default Value) C Agent Address 8Auto Auto assign agent address.
BIOS Setup Server CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Main Adv anced Boot Serv er Security Clk/Voltage Defaults Ex it Item Help }Sensor Information Halt On higf: Mov e Menu Lev el} [All, But Disk/Key ] Enter: Select +/-/PU/PD: Value F5: Prev ious Values F10: Sav e F7: Optimized Defaults Figure 4: Serv er 41 ESC: Ex it F1: General Help F8:Q-Flash
GA-8IEXW Motherboard CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Serv er Sensor Information Reset Case Open Status Item Help [Disabled] ø Case Opened Yes ø VCORE 1.746V ø VCC18 1.776V Current CPU Temperature -48oC Current CPU FAN Speed 4687 RPM Current POWER FAN Speed 0 RPM Current Sy stem FAN Speed 0 RPM +3.3V 3.37V +5V 5.10V +12V 11.
BIOS Setup C Sensor Information C Current CPU Temperature/System Temp.1/ System Temp.2 8Detect Temp. automatically. C Current CPU FAN/Power FAN/ System FAN Speed (RPM) 8Detect Fan speed status automatically . C Current System Voltag e: +3.3V / +5V / +12V 8Detect sy stem's v oltage status automatically . C CPU Warning Temperature 8Disabled Don’t monitor current temperature.(Default v alues) 860 C~90 C Alarmed w hen current temperature is ov er than the selected temperature.
GA-8IEXW Motherboard CHalt On The category determines whether the computer will stop if an error is detected during power up. 8NO Errors The system boot w ill not stop for any error that may be detected and y ou w ill be prompted. 8All Errors Whenev er the BIOS detects a non-fatal error the sy stem w ill be stopped. 8All, But Key board The sy stem boot w ill not stop for a key board error, and it w ill stop for all other errors.
BIOS Setup Security CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Main Adv anced Boot Serv er Security Clk/Voltage Defaults Set Superv isor Passw ord Item Help Set User Passw ord Passw ord Check Ex it Menu Lev el} [Setup] Change/Set/Disable Passw ord higf: Mov e Enter: Select +/-/PU/PD: Value F5: Prev ious Values F10: Sav e F7: Optimized Defaults ESC: Ex it F1: General Help F8: Q-Flash Figure 5: Security When you select this function, the following message will appear at th
GA-8IEXW Motherboard C Password Check 8System The system can not boot and can not access to Setup page will be denied 8Setup The sy stem w ill boot, but access to Setup w ill be denied if the correct if the correct passw ord is not entered at the prompt. passw ord is not entered at the prompt.
BIOS Setup Clk/Voltage CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Main Adv anced Boot Serv er Security Clk/Voltage Defaults Clk/Voltage Ex it Item Help Spread Spectrum Modulated CPU Clock Ratio [Enabled] [15x ] ø CPU Host Clock Control Disabled ø CPU Host Frequency (Mhz) 100 ø Fix ed PCI/AGP Frequency 33/36 ø Host DRAM Clock Ratio Auto ø Memory Frequency (Mhz) 266 ø PCI/AGP Frequency (Mhz) 33/36 higf: Mov e Enter: Select +/-/PU/PD: Value F5: Prev ious Values F10:
GA-8IEXW Motherboard Defaults CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Main Adv anced Boot Serv er Security Clk/Voltage Defaults Load Optimized Defaults Item Help Load Fail-Safe Defaults Menu Lev el} Ex it Load Fail-Safe Defaults higf: Mov e Enter: Select +/-/PU/PD: Value F5: Prev ious Values F10: Sav e F7: Optimized Defaults ESC: Ex it F1: General Help F8: Q-Flash Figure 7: Defaults CLoad Optimized Defaults When you press on this item, you will get a confirma
BIOS Setup Exit CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Main Adv anced Boot Serv er Security Clk/Voltage Defaults Ex it Sav e & Ex it Setup Item Help Ex it Without Sav ing Menu Lev el} Sav e Data to CMOS higf: Mov e Enter: Select +/-/PU/PD: Value F5: Prev ious Values F10: Sav e ESC: Ex it F1: General Help F7: Optimized Defaults Figure 8: Ex it F8: Q-Falsh CSave & Exit Setup Type “Y” will quit the Setup Utility and save the user setup value to RTC CMOS.
GA-8IDXR Motherboard Revision History Chapter 4 Technical Reference Block Diagram 50
Appendix Revision History Chapter 5 Appendix Appendix A: INF Update Utility Installation Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show a series of Setup Wizard dialog boxes. If not, please double click the CD-ROM device icon in "My computer", and execute the setup.exe. Installation Procedures: 1. The CD auto run program starts, Double click on “INF UPDATE UTILITY” to start the installation. 2.
GA-8IEXW Motherboard 5.Click "Finish" to restart computer.
Appendix Appendix B: Intel® 82550 Network Driver Installation: Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show a series of Setup Wizard dialog boxes. If not, please double click the CD-ROM device icon in "My computer", and execute the setup.exe. 2.Click "Next". 1.Click "Intel 82550 Network Driver" item. (1) (2) 4.Select Installation Type and Click "Next". 3.Click "Next".
GA-8IEXW Motherboard 5. Click "Install". 6. Starting installation. (6) (5) 5. Wizard Completed. Click "Finish". 8.Click "OK".
Appendix Appendix C: ATI-Rage XL VGA Driver Installation Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show a series of Setup Wizard dialog boxes. If not, please double click the CD-ROM device icon in "My computer", and execute the setup.exe. 2.Click "Next". 1. Click "ATI-Rage XL Driver" item. (2) (1) 4.Click "Finishl" to restart computer. 3.Click "Yes".
GA-8IEXW Motherboard Appendix D: Promise ATA Driver Installation Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show a series of Setup Wizard dialog boxes. If not, please double click the CD-ROM device icon in "My computer", and execute the setup.exe. 1. Click "Promise ATA Driver Information" item.
Appendix Appendix E: Intel® Application Accelerator Installation Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show a series of Setup Wizard dialog boxes. If not, please double click the CD-ROM device icon in "My computer", and execute the setup.exe. 2.Click "Next". 1. Click "Inel Application Accelerator" item. (1) (2) 4.Click "Next". 3.Click "Yes".
GA-8IEXW Motherboard 6.Click "Finishl" to restart computer. 5.Click "Next".
Appendix Appendix F: RealTek Audio Driver Installation Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show a series of Setup Wizard dialog boxes. If not, please double click the CD-ROM device icon in "My computer", and execute the setup.exe. 1.Click "RealTek Audio Driver" item 2.Click "Next". (2) (1) 5.Click "Finish" to restart computer. 4. Starting installation.
GA-8IEXW Motherboard Appendix G: Acronyms Acronyms ACPI APM AGP AMR ACR BBS BIOS CPU CMOS CRIMM CNR DMA DMI DIMM DRM DRAM DDR ECP ESCD ECC EMC EPP ESD FDD FSB HDD IDE IRQ I/O IOAPIC ISA Meaning Advanced Configuration and Power Interface Advanced Power Management Accelerated Graphics Port Audio Modem Riser Advanced Communications Riser BIOS Boot Specification Basic Input / Output System Central Processing Unit Complementary Metal Oxide Semiconductor Continuity RIMM Communication and Networking Riser Direct
Appendix Acronyms LAN LBA LED MHz MIDI MTH MPT NIC OS OEM PAC POST PCI RIMM SCI SECC SRAM SMP SMI USB VID Meaning Local Area Network Logical Block Addressing Light Emitting Diode Megahertz Musical Instrument Digital Interface Memory Translator Hub Memory Protocol Translator Network Interface Card Operating System Original Equipment Manufacturer PCI A.G.P.
GA-8IEXW Motherboard & Technical Support/RMA Sheet Customer/Country: Contact Person: Company: E-mail Add. : Model name/Lot Number: BIOS version: O.S./A.S.: Hardware Configuration CPU Memory Brand Video Card Audio Card HDD CD-ROM / DVD-ROM Modem Network AMR / CNR Keyboard Mouse Power supply Other Device Mfs. Phone No.
