Installation Guide

ManualsBrandsAmerican Standard ManualsBath4-piece Glue-Up Window Trim Kit in Dove White

755908-100 Rev. 1 06/20- 1 -

INSTALLATION INSTRUCTIONS

INSTALLING WINDOW TRIM

SAVE FOR FUTURE USE

REQUIRED TOOLS AND MATERIALS

Pencil

Tape Measure

Fine Tooth Saw

Personal Safety Equipment

TOOLS:

DAP 3.0 Advanced Hybrid

DAP Kwik Seal Ultra Sealant

MATERIALS:

NOTE: Window trim material is designed with enough material to be trimmed to

the specication of the window within the shower/bath area. There are decorative

squares on one end of each piece of trim. When put together the decorative

squares will be on all 4 corners of the window area.

See ILLUSTRATION 1

Apply window measurement to one piece of trim

at a time, plus the additional 2-1/4" (57 mm) to

account for trim overlap when installed.

See ILLUSTRATION 3

Measure all 4 sides of the window area for

length and depth.

See ILLUSTRATION 2

NOTE: Add an additional 2-1/4" (57 mm)

to each window dimension to account

for required overlap of trim on cut end.

For Customer Care, call 866-423-0800 from 9am to 6pm (EST, M-F)

ILLUSTRATION 1

ILLUSTRATION 3

X PLUS

2-1/4"

(57 mm)

ILLUSTRATION 2

INSTALLATION:

DECORATIVE

SQUARES

Cut window trim to the measurement obtained

above from the opposite end of the trim’s

decorative square. The inside or depth of the

trim will also have to be cut to the dimension

of the window sill. Rough edges can be

sanded smooth to obtain a good t after cut.

See ILLUSTRATION 4

ILLUSTRATION 4

CUT

HERE

NOTCHED FOR

WINDOW SILL

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS INSTALLING WINDOW TRIM For Customer Care, call 866-423-0800 from 9am to 6pm (EST, M-F) REQUIRED TOOLS AND MATERIALS TOOLS: MATERIALS: Pencil Tape Measure Fine Tooth Saw Personal Safety Equipment DAP 3.0 Advanced Hybrid DAP Kwik Seal Ultra Sealant U S E DECORATIVE SQUARES ILLUSTRATION 1 NOTE: Add an additional 2-1/4" (57 mm) to each window dimension to account for required overlap of trim on cut end.
PAGE 2
4 Dry fit the first piece of cut trim to the window, ensuring there are no gaps around the corners. NOTE: Approximately 2-1/4" of the trim’s front surface (that faces the shower area) will protrude beyond the window to account for the required overlap. 5 6 Proceed to a second piece of trim measuring, cutting, sanding and dry fitting for a proper fit over the window area. When mating one piece of trim with another, ensure the cut ends overlap under the decorative squares.
PAGE 3
INSTRUCCIONES DE INSTALACIÓN INSTALACIÓN DEL MARCO DECORATIVO DE LA VENTANA Para atención al cliente, llame al 866-423-0800 de 9 a.m. a 6 p. m. (hora estándar del este, de lunes a viernes) HERRAMIENTAS Y MATERIALES NECESARIOS HERRAMIENTAS: MATERIALES: Lápiz Cinta métrica Sierra de dientes finos Equipo de seguridad personal Sellador DAP 3.0 Advanced Hybrid U S O CUADRADOS DECORATIVOS ILUSTRACIÓN 1 2 Mida los 4 lados del área de la ventana para obtener su longitud y la profundidad.
PAGE 4
Monte en seco el primer trozo del marco decorativo en la ventana, asegurándose de que no haya espacios en las esquinas. NOTA: Aproximadamente 2-1/4" de la superficie delantera del marco decorativo (que da al área de la ducha) sobresaldrá más allá de la ventana, lo que corresponde a la superposición necesaria. 5 6 Mida, corte, lije y monte en seco una segunda pieza de marco decorativo verificando un ajuste adecuado sobre el área de la ventana.