Installation Guide

ManualsBrandsAmerican Standard ManualsBathICS Deep Basin Wall-Mounted Bathroom Sink in White

7301793-100 Rev. F

Introduction: Thank you for selecting our products...products which have been the

benchmarks of fine quality for years. To help insure that the installation process will

proceed smoothly, please read these instructions carefully before you begin. Also,

review the recommended tools and materials list; carefully unpack and examine your

new plumbing fixture.

Channel Lock Pliers

Regular Screwdriver

Recommended Tools & Materials

Rough-In

Dimensions

Phillips Screwdriver

Pipe Wrench

Drill

Plumbers' Putty or Caulking

Tubing Cutter

Tape

Measure

Hacksaw

Pencil

Torch

Level

SAVE FOR FUTURE USE

NOTE: Pictures may not exactly define contour of china and components.

ICS Sink with Selectronic IC Faucet*

Models: 9118.111, 9118.100 & 9118.150

INSTALLATION INSTRUCTIONS

Product names listed herein are trademarks of AS America, Inc.

14-3/4"

(375mm)

17"

(432mm)

4-3/4"

(121mm)

5/8"

(14mm)

1-5/8"

(41mm)

20"

(509mm)

4-3/4"

(120mm)

8" (203mm)

1/2" DIA.

(13mm)

FINISHED WALL

BASE MOUNT

DETAIL

FINISHED

FLOOR

FINISHED

FLOOR

FINISHED

FLOOR

26-1/8"

(663mm)

36"

(914mm)

36-1/2"

(927mm)

36-1/2"

(927mm)

40-1/8"

(1020mm)

2-3/4"

(70mm)

9/16" DIA.

(14mm)

2-3/4"

(70mm)

(102mm)

MOUNTING

STUDS

Adjustable Wrench

*FAUCET PERCH

2-1/2" DIA. (65mm)

*FAUCET PERCH

2-1/2" DIA. (65mm)

*DISCLAIMER: Faucets with a base diameter greater than 2-1/4" (57 mm) will not fit on

this ICS Sink. The Selectronic IC Faucet was specifically designed to minimize splashing

during operation. American Standard will not be liable for any splashing that occurs if

faucets other than the American Standard IC Faucets are used.

This product will not eliminate the risk of infection, but provides a hygienic environment

by reducing splashing through its unique design.

8"(203mm) BETWEEN

MOUNTING HOLES

RECOMMENDED CARRIERS:

JAY R. SMITH MFG. CO.

MODEL SQ-0-4437

FLOOR MOUNTED SINK SUPPORT

WATTS CA-311

FLOOR MOUNTED URINAL CARRIER

CAUTION: PRODUCT IS FRAGILE. TO AVOID DAMAGE AND POSSIBLE INJURY HANDLE WITH CARE!

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS ICS Sink with Selectronic IC Faucet* Models: 9118.111, 9118.100 & 9118.150 Introduction: Thank you for selecting our products...products which have been the benchmarks of fine quality for years. To help insure that the installation process will proceed smoothly, please read these instructions carefully before you begin. Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture. ! CAUTION: PRODUCT IS FRAGILE.
PAGE 2
1 2 ROUGH-IN SUPPLIES AND WASTE OUTLET 1. Rough-in 3/8" supplies and waste outlet connections. NOTE: For ease of installation and accessibility, it is recommended that straight stops with flex supply tubes be used. As an alternative, if rigid supply risers are used, it is suggested to use angle stops in place of the straight stops. 1. Insert WIRES (1), FLEX HOSE (2) and SPOUT SHANK (3) through center hole of mounting surface. 2.
PAGE 3
4 5 INSTALL ICS SINK 1. Mount SINK onto the two HANGER STUDS. Hold SINK in place and temporarily install NYLOCK NUT & WASHER on one of the HANGER STUDS to retain SINK. INSTALL ELECTRONICS HANGER BRACKET 1. Install the ELECTRONICS HANGER BRACKET onto remaining HANGER STUD. Install NYLOCK NUT & WASHER but do not tighten fully. 2. Remove NYLOCK NUT & WASHER from first HANGER STUD and install other end of ELECTRONICS HANGER BRACKET. Replace NYLOCK NUT & WASHER, tighten both ends.
PAGE 4
9 CONNECT WATER SUPPLY TO ENCLOSURE AND TO COLD OR TEMPERED WALL SUPPLY 1. Insert FIBER WASHER (4) into SUPPLY NUT (1) on ENCLOSURE (2). 2. Connect SUPPLY NUT (1) on ENCLOSURE (2) to FLEXIBLE SUPPLY HOSE (3). Tighten to make a water tight connection. Use two wrenches to tighten if necessary. 2 3. Connect FLEXIBLE SUPPLY (3) directly to wall supply. Connection on FLEXIBLE SUPPLY (3) is 3/8" compression. Use adjustable wrench to tighten connection. Do not over tighten.
PAGE 5
13 CHECK ALL ELECTRICAL AND PLUMBING CONNECTIONS 1. Turn on water supplies and check for leaks. Tighten any connections if necessary. No. M965119 I n s t a l l a t i o n I n s t ru c t i o n s 2. Check FAUCET operation, if adjustment is required refer to the installation instructions shown at right supplied with the IC FAUCET. No. M965119. SELECTRONIC® Proximity IC Faucet 14 TEST INSTALLED FAUCET TO ENSURE A LAMINAR WATER FLOW the air must be slowly purged from the spout.
PAGE 6
16 INSTALL SINK APRON 3. Remove the APRON. Clean the wall where the APRON BRACKETS supplied with SINK are to be applied. Peel off the protective strip from the back of the APRON BRACKETS. Apply the two APRON BRACKETS to the finished wall parallel to the pencil marks as shown in the illustration below. 1. Hold APRON up against SINK and flush against finished wall. 2. Mark a line with a pencil on the wall about 6" long as shown on both sides of the APRON. OPTIONAL MOUNTING.
PAGE 7
Repair Parts ICS Sink Models: 9118.111, 9118.100 & 9118.150 7381267-400.0070A Mounting Bracket Kit 7381243-251.0020A Offset Drain 7381242-0500A P-Trap Assembly 7381266-200.0070A Bracket Assembly 7381259-401.0200A ICS Sink Shroud Kit 7 7301793-100 Rev.
PAGE 8
AS AMERICA, INC. ONE YEAR LIMITED WARRANTY If inspection of this AS America, Inc. (“American Standard”) plumbing product, within one year after its initial purchase, confirms that it is defective in materials or workmanship, American Standard will repair or, at its option, exchange the product for a similar model. This limited warranty applies only to the original purchaser and installation of these products. In the event of a limited warranty claim, proof of purchase will be required—save sales receipt.