Installation & Assembly

ManualsBrandsAmerican Standard ManualsBathroom Remodel & Bathroom FixturesStudio S Monoblock Single Hole Bathroom Faucet with Drain Assembly

- 1 -

Product names listed herein are trademarks of AS America, Inc.

Thank you for selecting American Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly-please read

these instructions carefully before you begin.

RECOMMENDED TOOLS

M965779 (3/17)

INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON

STUDIO

MONOBLOCK LAVATORY FAUCET

WITH SPEED CONNECT

DRAIN

INSTALLATION

INSTRUCTIONS

7105.101

Screwdriver Adjustable Wrench Tubing CutterChannel Locks

Certied to comply with ANSI A112.18.1M

Optional

Escutcheon

and Putty Plate

MOUNTING

SURFACE

Figure A

CAUTION

Turn off hot and cold water

supplies before begining.

• Seat SEAL (1) into under side of ESCUTCHEON RING (2).

• Seat ESCUTCHEON RING (2) with collar facing up into groove in faucet

base.

• Feed FAUCET SUPPLIES (3), MOUNTING STUD (4) and DRAIN CABLE

ASSEMBLY (8) through ESCUTCHEON RING (2) and the mounting hole

of lavatory or mounting surface. Figure A.

• From below, push GASKET (7) and RETAINING WASHER (5) onto

MOUNTING STUD (4). Secure Faucet with MOUNTING NUT (6), pulling

faucet to front of sink, so SUPPLIES (3) rests against mounting hole.

Before nal tightening, make sure collar on MOUNTING NUT (6) is

seated into RETAINING WASHER (5).

• Adjust Faucet so that it is centered. Tighten MOUNTING NUT (6) to

complete faucet mounting.

COLLAR ON

MOUNTING NUT

Figure B

Summary of content (7 pages)

PAGE 1
INSTALLATION INSTRUCTIONS STUDIO® S 7105.101 MONOBLOCK LAVATORY FAUCET WITH SPEED CONNECT® DRAIN Thank you for selecting American Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.
PAGE 2
POP-UP DRAIN Fig. A. Fig. B. • Remove CLEAR PLASTIC COVER (1). 1 • Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 3 DRAIN BODY • Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 3 REMOVE FLANGE 4 Fig. A. • Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Fig. B. 1 • Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 3
7 ATTACH CABLE CONNECTOR Fig. A. Fig. B. • Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpipe on pop-up drain is 1-1/4" O.D. Fig. B. 2 1-1/4" O.D. 8 CHECK OPERATION OF POP-UP • Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.
PAGE 4
10 TEST INSTALLED FITTING 1 • With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. ON OFF COLD HOT • Remove AERATOR (3). 3 • Operate HANDLE (1) to flush water lines thoroughly. • Replace AERATOR (3). CHECK DRAIN CONNECTIONS 4 • Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in Sink.
PAGE 5
Speed Connect® Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 6
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be Removed) or “Unlock” Mode (Stopper is removable). Locked Mode: • Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. • To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front.
PAGE 7
STUDIO® S MONOBLOCK LAVATORY FAUCET WITH SPEED CONNECT® DRAIN MODEL NUMBER 7105.101 Replace the “YYY” with appropriate finish code M970230-YYY0A HANDLE KIT M970231-0070A GEAR AND PLUG KIT POLISHED CHROME 002 BRUSHED NICKEL 295 M951430-0070A CARTRIDGE M970248-YYY0A PLUG BUTTON & SCREW M923840-0070A AERATOR (1.2 GPM) M952430-0070A CABLE ASSEMBLY M970232-YYY0A POP-UP ROD M952425-YYY0A DRAIN ASSEMBLY 2064101P.