Installations & Assembly

8
M965652 Rev. 1.7 (10/16)
A
HAND WASH SENSOR OPERATION; Fig. 1
When the Sensor detects a user, the water immediately starts
toow.Waterowwillstop2secondsafteruserisoutof
sensorrange.Theoffdelayallowstheusertocomfortably
movehishandswithouttheowcyclingonandoff.Asa
precaution,asafetytimerwillturnoffthewaterafterthe
sensorhasbeenblockedfor59seconds.Thewaterwillstay
offuntiltheblockageisremovedfromthedetectionzone.
Detection Zone: 2" - 10" (50mm - 250mm)
Default: Set at Factory 6" (150mm)
B
CHANGE SENSOR RANGE;
(Factory set at 6") Fig. 2, 2a
1. RemoveCONTROLBOX.DisconnectPowerSupply(1),
then reconnect. Fig. 2.
2.WhiletheSENSORCONTROLLED (2) is blinking slowly,
placeyourhand1-2in.(30-50mm)infrontofthesensor.
Fig. 2a.
3.WhentheLEDstopsblinkingandstays“ON”,moveyour
handtothedesiredpositionandholdinplaceuntiltheLED
begins to blink again. Fig. 2a.
4.OncetheSENSORCONTROLLED (2) begins to blink
again,removeyourhandfromthedetectionzone.Whenthe
ashing stops, the detection distance is set.
5. Reinstall CONTROLBOXCOVERS(2). Tighten cover
screws rmly.
C
CLEAN FILTER ASSEMBLY; Fig. 3
1. Remove CONTROLBOXCOVER.
2. Close SUPPLY STOP (13)with4mmHexwrench.
Note: Activate sensor to keep water owing out of
faucet while shutting off.
3.UnthreadFILTERASSEMBLY (6) using a 7/16" socket.
4.PullouttheFILTERASSEMBLY(6), remove and clean
white debris cup and lter screen.
5.InstalltheFILTERASSEMBLY(6) back in its place and
tighten with a 7/16" socket.
Caution: Do not over tighten.
6. Open SUPPLY STOP (13) with4mmHexwrench.
7. Reinstall CONTROLBOXCOVER.Tightencover
screws rmly.
Fig 1
5
6
4
10
3
DETECTION
ZONE
Fig. 2
1
Fig. 2a
1" - 2" (30mm - 50mm)
BLINKING LED
UP TO 10" (250mm)
BLINKING
LED
2
2
6
WHITE
DEBRIS
CUP
FILTER
SCREEN
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Fig. 3
7/16" SOCKET
4mm HEX WRENCH
13
CAUTION
Before opening CONTROL BOX
disconnect AC power supply.
MAINTENANCE