Installation Guide

3
M965651 Rev. 1.5 (10/16)
Fig. 1
1
1
2
3
4
5
3
SENSOR
CABLES
1
2
3
4
5
6
7
10'
Roughing-in Dimensions
RECOMMENDED TOOLS
1. Slip Joint Pliers
2. Adjustable Wrench
3. Plumbers’PuttyorCaulking
4. Phillips Screwdriver
5. Flat Blade Screwdriver
6. ElectricDrill&1/4"DrillBit
7. Tape Measure
114mm
(4-1/2)
500mm
(20")
1524mm
(60)
413mm
(16-1/4)
3/8" COMP.
32mm
(1-1/4) DIA.
125mm
(4-7/8)
81mm
(3-3/16)
60mm
(2-3/8) MAX.
MOUNTING
SURFACE
(243mm)
9-9/16"
(127mm)
5"
(133mm)
5-1/4"
(53mm)
2-1/8" DIA.
RECOMENDED ELECTRICAL BOX OR
EQUIVALENT BY OTHERS
HARD-WIRED AND MULTI AC 10’ MAX. CABLE LENGTH
4" (102mm) SQ. X 3-1/2" (89mm) DEEP ELECTRICAL BOX
Hubbel-RACO #256 OR EQUAL (BY OTHERS).
114mm
(4-1/2)
500mm
(20")
1524mm
(60)
413mm
(16-1/4)
3/8" COMP.
32mm
(1-1/4) DIA.
125mm
(4-7/8)
81mm
(3-3/16)
60mm
(2-3/8) MAX.
MOUNTING
SURFACE
(243mm)
9-9/16"
(127mm)
5"
(133mm)
5-1/4"
(53mm)
2-1/8" DIA.
RECOMENDED ELECTRICAL BOX OR
EQUIVALENT BY OTHERS
HARD-WIRED AND MULTI AC 10’ MAX. CABLE LENGTH
4" (102mm) SQ. X 3-1/2" (89mm) DEEP ELECTRICAL BOX
Hubbel-RACO #256 OR EQUAL (BY OTHERS).
GENERAL DESCRIPTION
Electronicfaucetwithproximityoperation.Vandalresistant,
solidbrassconstruction,singlepostmounting.OperatesonDC
(battery/powerpack)orACpermanentpower(plug-in/hardwire).
In-linestrainerforsolenoidisintegral.Singleinlet3/8
compression,built-incheckvalves,andexiblestainlesssteel
16-1/4" reach inlet hose for spout connection.
Note: All plumbing and electrical wiring must be installed
in accordance with applicable codes, regulations
and standards.
CAUTION: Use only American Standard supplied
transformers and cable sets. Using non-AS supplied cables,
or cutting, splicing or modifying any components will void
the warranty.
1
SPOUT ASSEMBLY INSTALLATION;
Fig. 1
1. Connectthetwo27"EXTENSIONCABLES (1) to
the Faucet Sensor Cables.
2. Insert27"EXTENSIONCABLES (1),FLEX
HOSE (2)andSPOUTSHANK (3) through center
hole of mounting surface.
3.Assemble“C”WASHER (4)andLOCKNUT (5)
ontoSPOUTSHANK(3) from underside of
mounting surface.
4.AlignFAUCETandtightenLOCKNUT (5).
Note: 4" and 8" Deck Plates are available for other
installations, see page one for information.
CAUTION
Turn off hot and cold water
supplies before beginning.
FAUCET INSTALLATION