Installation Guide

Turn Off Water Supply
Flush to remove
water from tank;
sponge remaining
water from
bowl before
removing toilet.
Clean Flange
!
Caution: If leaving floor flange
open for more than 1-2 hours,
cover flange to prevent escaping
sewer gases.
ROUGHING-IN DIMENSIONS:
NOTE: Distance from wall to closet flange
centerline must be as listed:
Studio
®
ActiVate
™
Right Height
®
Elongated
2-piece Toilet Model 2794.119
Studio
®
ActiVate
™
Right Height
®
Round
Front 2-piece Toilet Model 2795.119
7302165-100 Rev. A
- 2 -
BACK-TO-BACK INSTALLATION
Recommended fitting type for
back-to-back installations.
Depending upon your plumbing and venting conditions, the flow from the toilet in a back-to-back
installation may create a vacuum on the system and draw water from the opposing bowl. The
National Standards Plumbing Code prohibits the use of a cross fitting for drainage as throw over
is possible. The code does approve a directional "Y" style fitting with proper venting to direct the
water downward and away from the other toilet.
IMPORTANT: Water supply on the wall is required at 2-1/4" or 8" from centerline of the toilet (see rough-in). First suggested
position is hidden behind the toilet. The geometry of the toilet gives space for this installation. The second suggested position
is next to the toilet. Between these two positions, the space for the supply between wall and toilet is limited to 4-1/2". In this
case, check your supply and hose dimensions.
28-3/16"
(716mm)
8-3/4"
(221mm)
1-1/8"
(29mm)
16-1/2"
(419mm)
4-1/2"
(114mm)
3-1/8"
(81mm)
2-5/8" (67mm)
7-1/2"
(191mm)
12-7/8"
(328mm)
12-3/16"
(309mm)
16-1/2"
(419mm)
15-3/4"
(399mm)
12"
(305mm)
FINISHED
FLOOR
FINISHED WALL
C/L OF SEAT POST
HOLES 5-1/2"
(140mm) CENTERS
SUPPLY AS
REQUIRED
(position 1 or
position 2)
6"
(152mm)
5-1/2"
(140mm)
14"
(356mm)
8"
(204mm)
BACK VIEW (for reference)
30-3/4"
(781mm)
C/L OF OUTLET
2-1/4"
(57mm)
30-1/4"
(768mm)
8-3/4"
(221mm)
1-1/8"
(29mm)
18-1/2"
(470mm)
4-1/2"
(114mm)
3-1/8"
(81mm)
2-5/8" (67mm)
7-1/2"
(191mm)
13-11/16"
(347mm)
12-3/16"
(309mm)
16-1/2"
(419mm)
15-3/4"
(399mm)
12"
(305mm)
FINISHED
FLOOR
FINISHED WALL
C/L OF SEAT POST
HOLES 5-1/2"
(140mm) CENTERS
SUPPLY AS
REQUIRED
(position 1 or
position 2)
6"
(152mm)
5-1/2"
(140mm)
14"
(356mm)
BACK VIEW
(for reference)
30-3/4"
(781mm)
C/L OF OUTLET
2-1/4"
(57mm)
8"
(204mm)
IMPORTANT: Water supply on the wall is required at 2-1/4" or 8" from centerline of the toilet (see rough-in). First suggested
position is hidden behind the toilet. The geometry of the toilet gives space for this installation. The second suggested position
is next to the toilet. Between these two positions, the space for the supply between wall and toilet is limited to 4-1/2". In this
case, check your supply and hose dimensions.
Before You Start:
If Removing An Existing Toilet
IMPORTANT: Water supply on the wall is
required at 2-1/4" or 8" from centerline of the
toilet (see rough-in). First suggested position
is hidden behind the toilet. The geometry of
the toilet gives space for this installation. The
second suggested position is next to the toilet.
Between these two positions, the space for the
supply between wall and toilet is limited to
4-1/2". In this case, check your supply and
hose dimensions.
IMPORTANT: Water supply on the wall is
required at 2-1/4" or 8" from centerline of the
toilet (see rough-in). First suggested position
is hidden behind the toilet. The geometry of
the toilet gives space for this installation. The
second suggested position is next to the toilet.
Between these two positions, the space for the
supply between wall and toilet is limited to
4-1/2". In this case, check your supply and
hose dimensions.