Installation Instructions

ManualsBrandsAmerican Standard ManualsFaucet Accessories2000.102P.002

COLLAR ON

MOUNTING NUT

M968760 Rev. 1.4

Certiﬁed to comply with ANSI A112.18.1

Installation

Instructions

Centerset Lavatory Faucet with

Speed Connect™ Drain

Adjustable Wrench Screwdriver Channel Locks

Recommended tools

2000.10X

2000.16X

INSTALL FAUCET

GROOVE

(FAUCET

BASE)

Seat SEAL (1) into under side of FAUCET BASE (2).

Feed FAUCET SUPPLIES (3), MOUNTING STUD (4) and DRAIN

CABLE ASSEMBLY (8) through ESCUTCHEON (9) (optional) and the

mounting hole of lavatory or mounting surface. Fig. A.

From below, push GASKET (7) and RETAINING WASHER (5) onto

MOUNTING STUD (4). Secure Faucet with MOUNTING NUT (6),

pulling faucet to front of sink, so SUPPLIES (3) rests against

mounting hole. Before ﬁnal tightening, make sure collar on

MOUNTING NUT (6) is seated into RETAINING WASHER (5).

Fig.B.

Adjust Faucet so that it is centered. Tighten MOUNTING NUT (6)

to complete faucet mounting.

Fig. B.

Fig. A.

Congratulations on purchasing your American Standard

faucet with Speed Connect drain, a feature found only on

American Standard faucets.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Speed Connect™ Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the first time, every time.

Turn off water at

main supply.

CAUTION

Summary of content (6 pages)

PAGE 1
TM Centerset Lavatory Faucet with Speed Connect™ Drain Installation Instructions 2000.10X 2000.16X Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Certified to comply with ANSI A112.18.1 Speed Connect™ Drain* M 9 6 8 76 0 R ev. 1. 4 • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time.
PAGE 2
POP-UP DRAIN Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 3 DRAIN BODY Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 3 REMOVE FLANGE 4 Fig. A. Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Fig. B. 1 Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 3
7 ATTACH CABLE CONNECTOR Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 8 1-1/4” O.D. CHECK OPERATION OF POP-UP 1 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.
PAGE 4
10 TEST INSTALLED FITTING With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. 1 4 Remove AERATOR (3). Operate HANDLE (1) to flush water lines thoroughly. Replace AERATOR (3). CHECK DRAIN CONNECTIONS 3 Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in SINK. If DRAIN STOPPER (5) does not seal properly, please refer to Troubleshooting section in these instructions.
PAGE 5
Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 6
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front.