Installation Guide
8. Set the pedestal back in place. Put a 3/4" washer
on each of the screw(s), then screw the screw(s) for
the pedestal loosely to the floor.
9. Examine the alignment of the pedestal lavatory
to the wall to be sure it is centered where you want
it. Also check the level and adjust as needed.
Tighten the screw(s) at the base of the pedestal leg.
CAUTION: Do not over-tighten, as this may crack
the vitreous china.
10. Remove the lavatory and slide the hangers
upward to their highest positions. Reset the lavatory
to position the hangers in their final position.
Remove the lavatory once more and tighten the
hangers firmly into place, using additional screws.
11. Place the new lavatory on a thick layer of
newspapers, dropcloth, or the box in which it
was packed to protect it from scratches.
Attach the pop-up drain and the faucet to the
lavatory according to the faucet manafacturer's
instructions. You may also attach the hot and cold
water supply tubes to the faucet at this time.
Sealant may be required around the faucet and
pop-up where they meet the china. Check the
faucet manufacturer's recommendations. These
steps are easier to do before you mount the
lavatory in its place.
Reset the lavatory and anchor to the wall using the
bolt provided with the lavatory. Hole for anchoring
is located on the bottom of the lavatory near the
back corner as shown in FIGURE 3.
12. Connect the drain trap to the pop-up drain tail
piece, then join the trap to the drain pipe in the
wall. You may use metal or plastic drain pipe
and trap following the directions provided by
the manufacturer.
13. Use a tube cutter to trim the free ends of the hot
and cold supply tubes to at least 1/4" longer than
necessary to reach into the inlets of the shut-off
valves. It is better to cut the tubes longer than
needed, then trim them again. Remove any burrs or
sharp edges with an emory cloth.
Join the hot and cold water supplies to the shut-off
valves as instructed by the manufacturer.
14. Turn the main water supply on, then open the
shut-off valves. Check all connections for leaks. A
slight tightening of about 1/4 turn will normally stop
any leaks.
15. Many people prefer a bead of caulking applied
at joint between lavatory and wall. Apply caulking
now, following caulking manufacturer's instructions.
15. Everyday cleaning of American Standard
china products maybe accomplished by using an
antibacterial liquid dishwashing soap and water.
For stubborn stains, use AJAX
®
or Comet
®
sparingly. Read and follow all label directions. In
all cases, rinse thoroughly with plenty of water
and dry the fixture.
In areas with hard water, a buildup of mineral
deposits or lime may make the finish of the
product appear dull. To remove lime buildup on
vitreous china products, KRC-7
®
liquid cleaner
may be used. Read and follow all label directions.
In all cases, rinse thoroughly with plenty of water
and dry the fixture.
Parts Policy...In order to avoid unnecessary delay or
uncertainty in the satisfaction of warranty claims,
buyers are advised to return alleged defective parts
to the place of purchase. Sellers are authorized to
address and resolve all warranty claims on fixtures
directly with buyers.
Your limited warranty is packed in with your lavatory.
FC-071-1102
CARE AND CLEANING
PARTS
INSTALLING YOUR NEW
LAVATORY (continued)
Fixture dimensions are nominal and conform to tolerances established by
ANSI standards A112.19.2M
7"
(178mm)
15-1/2"
(394mm)
11"
(279mm)
HANGER
ATTACH
HANGERS
FINISHED WALL
CENTER OF SLOT
ON HANGER
FINISHED WALL
FINISHED FLOOR
OUTLET
7-1/2"
(191mm)
18-1/2"
(470mm)
22"
(559mm)
4"
(102mm)
2-1/4"
(57mm)
13-1/4"
(337mm)
29-3/4"
(756mm)
3-1/2"
(89mm)
12-3/4"
(324mm)
3-1/2"
(89mm)
10"
(254mm)
7-1/4"
(184mm)
9-1/4"
(235mm)
3/8" HOT
WATER
(10mm)
3/8" COLD
WATER
(10mm)
31"
RIM HEIGHT
(787mm)
C
L
C
L
FOR MORE INFORMATION
CUSTOMER SERVICE: 1-800-442-1902
www.americanstandard-us.com
www.craneplumbing.com
www.eljer.com