Quick Start Guide

Table 1: Camera buttons / connections
Button / connections
Description
Alarm in 1
Alarm in 2
Alarm out
COM
Audio line in
Audio line out
Ground
Analog out cable connection
Micro SD card slot
AC 24 V
AC power connection
USB cable connection
Reboot button (Hold for 10 seconds)
Reset button (Hold for 20 seconds)
RJ45 Ethernet cable connection / PoE+
Security
3. Attaching the camera to a pendant or pole 1 ½ ‘’ NTP pipe
(continued)
B. Unscrew the M5 Hex socket cap screw (1) (Figure 8) to remove the
mounting arm plate (2) (Figure 8) from the mounting arm (3) (Figure 8).
Figure 8
C. Push the pin (1) (Figure 9) and place the camera onto the hinge and release
the pin so that the camera is attached to the mounting arm plate.
Figure 9
3. Attaching the camera to a pendant or pole 1 ½ ‘’ NTP pipe
(continued)
D. See step 4 to connect the power cable and then continue on at step E.
E. Securely attach the mounting arm plate to the camera with the four T10
screws (1) (Figure 10) on the mounting arm plate.
Figure 10
F. Place the mounting plate arm and camera into the pendant mount adaptor
(1) (Figure 11) and securely attach the two M3x0.5P (L = 6mm) screws with
the T10 security Torx wrench.
3. Attaching the camera to a pendant or pole 1 ½ ‘’ NTP pipe
(continued)
Figure 11
4. Connecting the power cable to the power plugs
A. Connect the power cable to the power plugs with one of the following
options:
 AC 24V: Connect 24V cables to terminals AC 24V.
 PoE+: Connect the RJ45 jack to a PoE compatible network device
that supplies power through the Ethernet cable.
5. Adjusting the camera position
A. Use the T10 security Torx wrench to adjust the bracket Tilt angle (2) (Figure
6) and to adjust the bracket Pan angle (3) (Figure 6).
6. Adjusting the sun shield hood
A. Move the sun shield hood (4) (Figure 6) forward and backward to adjust the
position of the sunshade.
Note: When the camera is mounted inverted to a pendant 1 ½ ‘’ NTP pipe you
must remove the sun shield hood by unscrewing the M3x0.5P (L = 8mm)
screw with the T10 security Torx wrench (3) (Figure 11) and relocate the
sun shield with screw as per the sun shield hood located in Figure 11.
CAUTION: Extending the sun shield hood forward could obstruct the field of view
(FOV) when the camera lens is set to ‘Wide’.
7. Location of camera buttons, connections and Desiccant bag
Note: The figure below indicates the location of the camera buttons and
connections (1) (Figure 12) and Desiccant bag (2) (Figure 12) on the camera.
Figure 12
Table 2: Universal Mounting plate symbols and descriptions
Plate
Symbol
Name
Description
4
4S Junction
Box
Attach the plate to a North American 4 inch
square electrical box.
O
Octagon Box
Attach the plate to a North American octagon
electrical box.
U
Electrical box
(UK)
Attach the plate to a UK electrical box.
E
Electrical box
(EU)
Attach the plate to a European electrical box.
Warnings
1. For US and Canada use a NRTL listed power adaptor.
2. The mains power adaptor equipment should be marked LPS (Limited
Current Source) or PS2 and rated according to 50C, 24VAC, 1.27A min
or PoE IEEE802.3at type 2 Class 4, 48VDC, 0.38A min.
3. To meet security immunity requirements use an uninterruptable PSU to
supply power to the mains adaptor or POE mid/end span.
4. The cables for 24Vac, Audio and Alarms should not exceed 3m unless
additional measures are taken to reduce the effect of interference picked
up on the cables.
5. USB and Analogue Video out cables should only be used temporarily for
service and not permanently installed.
6. For outdoor use the camera should be mounted at least 3m above ground
level”
© 2019 Johnson Controls. All rights reserved.
JOHNSON CONTROLS, TYCO and ILLUSTRA are trademarks and/or registered
trademarks. Unauthorized use is strictly prohibited.