Illustra Flex Series 3MP and 8MP Outdoor Bullet Cameras Quick Start Guide
Notice Please read this manual thoroughly and save it for future use before attempting to connect or operate this unit. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. Copyright © 2020 Johnson Controls. All rights reserved. JOHNSON CONTROLS, TYCO and ILLUSTRA are trademarks and/or registered trademarks. Unauthorized use is strictly prohibited.
Table of Contents Illustra Flex Series 3MP and 8MP Outdoor Bullet Cameras 1 Product features 1 Product overview 1 Installation 5 System requirements 10 Network Connection 11 Default IP Address 11 DHCP 12 Managing cameras with the Illustra Connect tool 13 Network Topology 15 Appendix A: Technical Specifications 16 Appendix B: Stream Resolutions 20
Warning • This unit operates at AC 24V/ PoE. • Installation and service should be performed only by qualified and experienced technicians and comply with all local codes and rules to maintain your warranty. • To reduce the risk of fire or electric shock, do not expose the product to rain or moisture. • Wipe the camera with a dry soft cloth. For tough stains, slightly apply with diluted neutral detergent and wipe with a dry soft cloth.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide Illustra Flex Series 3MP and 8MP Outdoor Bullet Cameras Product features Lens cases require special care when handling and cleaning to avoid scratches. For information on bubble handling and cleaning, see 8200-1174-01 Bubble Clearing Procedure Application Note. Go to https://illustracameras.com/products. From the Products page, select your camera product range and then select your camera model.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide Figure 3 on page 2 and Figure 4 on page 3 illustrates dimensions and physical properties of the units as well as a pictorial index of the camera connectors. Descriptions of these connectors are available in Table 5 on Page 3. Note:The connector cable of the Outdoor Bullet Camera should be contained in a conduit suitable for outdoor use.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide Figure 4 3MP (IFS03B1ONWIT) and 8MP Cameras dimensions (mm) and pictorial index Table 5 Pictorial index descriptions Index number Name Description 1 I/O connectors Connection for Input/Output devices. 2 Power Connector Connection to the external power source at AC 24V only. 3 BNC cable Connection for a BNC cable for analog out.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide Table 6 Input/Output connector descriptions Icon Description Alarm In Alarm Out Audio In Audio Out Power Ground You can find the interior buttons and ports on the base of the Illustra Flex Bullet camera. Remove the two screws to open the cover for access to these pins. Refer to Figure 7 on page 4 and Table 8 on Page 5 for descriptions of these buttons and ports.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide Table 8 Descriptions of the interior buttons and ports of the Illustra Flex Bullet camera Index number Name 1 Micro SD card slot 2 Serial port 3 Default: returns to factory default by pressing the button for five seconds 4 Reset: system restart CAUTION When removing the screws for the default/reset cover, ensure you replace and tighten the screws to avoid water leaking after adjustment.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide Remove the protective part of the unit when every item is checked in accordance with the list in In the box on page 5. Procedure 1 Mounting the camera Step Action 1 Affix the mounting template to the surface. After you drill the holes, knock in 4 plastic anchors and then lock in the 4 self-tapping screws to fasten the camera to the surface.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide Figure 11 Mounting the Illustra Flex 3MP (IFS03B1BNWIT) Bullet camera to a wall Figure 12 Mounting the Illustra Flex 3MP (IFS03B1ONWIT) and 8MP Bullet cameras to a wall WARNING Depending on the material of mounting surface, different screws and anchors than those supplied with the product may be required.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide Procedure 2 Connecting the wires Step Action 1 Attach the camera to the fixed surface. 2 Pass all the signal cables through the mounting bracket. 3 Connect the power cable to the power plugs with one of the following options: 4 a AC 24V: Connect 24V (~) cables to terminals ~AC 24V. b PoE: Connect the RJ-45 jack to a PoE compatible network device that supplies power through the Ethernet cable.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide Figure 14 Adjusting the 3MP (IFS03B1ONWIT) and 8MP camera position - End - Procedure 4 Adjusting the sun shield hood Step Action 1 Move the sun shield hood forward and backward to adjust the position of sunshade. CAUTION • Ensure to adjust the sun shield hood in coordination with lens in case of sunshade problems. • To avoid damage to the housing of the unit, do not adjust the sun shield position excessively.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide System requirements The table below lists the minimum requirement to implement and operate an Illustra Flex Bullet camera. Table 15 System Requirements System hardware CPU Intel Pentium 2 2.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide Network Connection Default IP Address Since this is a network-based unit, an IP address must be assigned at the very first bootup. The default IP address of the unit is 192.168.1.168 and sub mask is 255.255.255.0. However, if you have a DHCP server in your network, the unit obtains an IP address automatically from the DHCP server so that you do not need to change the IP address of the camera.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide Procedure 5 Connecting from a computer Step Action 1 Ensure the camera and your computer are in the same subnet. 2 Check whether if the network is available between the unit and the computer by pinging the default IP address. 3 a Start a command prompt. b Type “Ping 192.168.1.168”. If the message “Reply from…” appears, it means the connection is available. Start Internet Explorer and enter IP address: 192.168.1.168.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide 5 a Enter the IPv4 Address in the IPv4 Address text box in the form xxx.xxx.xxx.xxx.The default setting is ‘192.168.1.168’ b Enter the Network Mask in the Network Mask text box xxx.xxx.xxx.xxx. The default setting is ‘255.255.255.0’ c Enter the Gateway IP address in Gateway text box xxx.xxx.xxx.xxx. d Enter the Primary DNS Server in the Primary DNS Server text box xxx.xxx.xxx.xxx. Select Apply to save the settings.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide Procedure 9 Connecting to the camera using the static IP address Step Action 1 The camera attempts to obtain an IP Address from the DHCP Server. When no DHCP Server is available the camera is assigned a Static IP address of 192.168.1.168. 2 Open Microsoft Internet Explorer and enter the URL of the camera as 192.168.1.168. The camera sign in page displays.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide Network Topology The Illustra Flex cameras deliver video images and audio in real-time using the Internet and Intranet. It is equipped with an Ethernet RJ-45 network interface. The following images illustrate the network topology of the cameras.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide Appendix A: Technical Specifications The table below lists technical specifications of the Illustra Flex Outdoor Bullet cameras. General Features Model Type Illustra Flex Outdoor Bullet Camera Model No.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide Aperture Range 3MP (IK7 & IK10) = F/1.4(W) ~ F/2.7(T) 8MP (IK9 & IK10) = F/1.5(W) ~ F/2.91(T) Focal Length Range 3MP (IK7 & IK10) = 2.8-12 mm 8MP (IK9 & IK10) = 3.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide Video Imaging 3MP includes WDR, TrueWDR, TWDR3x Dynamic Range Method 8MP does not include TWDR3x Noise Reduction 2D and 3D NR Audio Sampling Bits 16-BIT Input Type SE/Line/MIC Input Impedance 20K/Attenuation = 0 dB Maximum Input Level 2Vp-p Input connector Terminal Block Output Type Impedance Hi impedance Maximum Output 2Vp-p I/O Interfaces SD Card SDXC slot up to 128GB Alarm Inputs 1 Auxiliary Outputs 1 Video Output Yes, PAL
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide IEEE 802.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide Appendix B: Stream Resolutions Flex Gen 2 3MP and Flex 8MP Streaming Combinations Table 19 on page 20 and Table 20 on page 21 provide information for the stream resolutions and supported FPS of the Flex Gen 2 3MP cameras herein. Table 21 on page 22 provides information for the stream resolutions and supported FPS of the Flex 8MP cameras.
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide Table 20 Stream Set B (all resolution, codes and frame rate combinations of Stream 1, 2 and 3 are valid) Frame Stream Codecs Resolution Stream Rates (fps) Stream 1 Codecs Resolution 1664x936 1280x720 Stream Resolution H265/H26 IntelliZip (fps) TWDR Support H264/H264 IntelliZip 31-60 1280x720 H265/H26 IntelliZip MJPEG H264/H264 IntelliZip H264/H264 IntelliZip 31-60 1024x576 H265/H26 IntelliZip MJPEG MJPEG H264/H264 IntelliZip H
Illustra Flex 3MP and 8MP Outdoor Bullet Quick Start Guide Table 21 Flex 8MP Bullet Camera resolutions Flex 8MP Bullet camera resolutions Stream 1 FPS Stream 2 FPS Stream 3 (3840x2160) 4K 16:9 (1280x720) 720p (640x360) nHD 16:9 (3264x1840) 16:9 (1024x576) PAL+ 16:9 (480x360) 480 4:3 (2592x1944) 4:3 1-15 (640x360) nHD 16:9 (2688x1520) 16:9 (480x360) 480 4:3 (2048x1536) QXGA 4:3 (384x288) 4:3 1-15 or 1-30 (384x288) 4:3 FPS 7-15 (1920x1080) 1080p 16:9 (1280x960) SXGA 16:9 1-60 (1280X7
