Installation Guide
Table Of Contents
- Overview
- Illustra Flex Series 3MP and 8MP Indoor Dome Camera
- Illustra Flex Series 3MP and 8MP Outdoor Dome Camera
- Illustra Flex Series 3MP and 8MP Outdoor Bullet Cameras
- Illustra Flex Series 3MP and 8MP Indoor Box Camera
- Illustra Flex 3MP Outdoor Compact Mini Dome Camera
- Illustra Flex Series 2MP Indoor and Outdoor IR PTZ Camera
- Illustra Flex 2MP Indoor Micro Dome Camera
- Network Topology
- Network Connection
- Configuration
- Appendix A: User Account Access
- Appendix B: Using Media Player to View RTSP Streaming
- Appendix C: Stream Tables
- Appendix D: Camera Defaults
- End User License Agreement (EULA)
6 8200-1456-01 M0
Warning
• These units operate at AC 24V/ PoE (the Box camera also supports DC12V). The Indoor IR PTZ unit operates at
PoE+ IEEE 802.3at or 24Vac. The Outdoor IR PTZ unit operates at PoE Ultra 802.3bt or 24Vac. WARNING: If
you do not use an injector which is standard 802.3bt then the camera wont work. The Compact Dome and Micro
Dome cameras are powered by PoE (IEEE802.3at class 1).
• Installation and service should be performed only by qualified and experienced technicians and comply with all
local codes and rules to maintain your warranty.
• The Box, Bullet, Mini-Dome and IR PTZ cameras are not intended to be directly connected to an external
network and the video coax connections should only be connected intra-building.
• To avoid damaging the Box, Bullet, Mini-Dome and IR PTZ cameras, never connect more than one type of power
supply (PoE IEEE802.3 Ethernet Class 0) at the same time. If using any type of PoE, these cameras must be
connecting only to PoE networks without routing to heterogeneous devices.
• The Micro Dome accessory extension cables are supplied with two clip-on ferrites for EMI suppression. These
need to be installed 5cm (2”) from each end.
• To reduce the risk of fire or electric shock, do not expose the product to rain or moisture.
• Wipe the camera with a dry soft cloth. For tough stains, slightly apply with diluted neutral detergent and wipe with
a dry soft cloth.
• Do not apply benzene or thinner to the camera, which may cause the surface of the unit to be melted or lens to be
fogged.
• The power supply shallbe approved for ITE NEC Class 2 or LPS with a rating of 24VAC, 550mA minimum and 50
degrees Celsius. The Compact Mini Dome power supply shallbe approved for ITE NEC Class 2 or LPS, 550mA
minimum and 50 degrees Celsius.
• Video Out connection should be intra-building only.
• Avoid operating or storing the unit in the following locations:
• Extremely humid, dusty, or hot/cold environments. Recommended operating temperature is:
• Indoor Minidome: -20˚C to 50˚C (-4˚F to 122˚F)
• Outdoor Minidome: -50˚C to 50˚C (-58˚F to 122˚F)
• Bullet: -40˚C to 50˚C (-40˚F to 122˚F)
• Box: -20˚C to 50˚C (-4˚F to 122˚F)
• Compact Mini Dome: -40˚C to 50˚C (-40˚F to 122˚F)
• Indoor IR PTZ: -20˚C to 50˚C (-4˚F to 122˚F)
• Outdoor IR PTZ: -50˚C to 50˚C (-58˚F to 122˚F)
• Indoor Micro Dome: -10˚C to +40˚C (14˚F to 104˚F)
• Power over Ethernet (PoE) does not support heater.
• Near sources of powerful radio or TV transmitters.
• Near fluorescent lamps or objects with reflections.
• Under unstable or flickering light sources.