Quick Setup Guide EDVR Part Number 8200-0841-00 A0
EDVR Quick Setup Guide A. Check System Components American Dynamics EDVR Unit Supplied Accessories Two Power Cords: (1) North American standard (2) Continental European standard CD-ROM (Viewer software and user documents in electronic form) and this printed Quick Setup Guide Power Brick (External Power Supply) Rack Mount Kit Alarm I/O Adapter Required Items • Composite Monitor (PAL or NTSC) • Cameras and BNC Cables B.
EDVR Quick Setup Guide 4 Connect one or more cameras to the Video In BNC connector(s). Note For video loop through, Touch Tracker (ADTT16E), and other connections, refer to the Installation and Operation Guide that is included on the CD-ROM. Video In (BNC) Video Loop Through (BNC) Call Monitor Connector (BNC) Main Monitor Connector (BNC) Network Connector (Ethernet; RJ-45) Power Connector (12v) C.
EDVR Quick Setup Guide D. (Optional) Select Video Output: NTSC or PAL From the factory, the EDVR is configured for NTSC video output. However, if you need to change video output to PAL, or change PAL to NTSC, complete the following steps: 1 If the EDVR and the Main Monitor are not turned on, turn them on. 2 On the EDVR Front Panel, simultaneously press the Up and Pause buttons for at least 3 seconds. After you hear a long beep, release both buttons.
EDVR Quick Setup Guide F. (Optional) Install EDVR Client Software To remotely view and manage one or more EDVRs from a PC, install the included EDVR Client Software. Note Both the EDVR and the PC must be physically connected to the same network (LAN). 1 Insert the enclosed CD in the CD-ROM drive of the PC from which you wish to remotely monitor one or more EDVRs. The software installation automatically starts. 2 Follow the on-screen instructions.
EDVR Quick Setup Guide H. Connecting ADTT16E to EDVR 1 Connect the hardware. Refer to the following diagram: BNC Video EDVR Sensornet RS232 9600 Baud EIM DOME Power RS232 over Cat 5 Cable Set Configure Deivces to MUX 16 Duplex/Triplex Note: Do not use MUX 16 posem 2 Configure the Touch Tracker (Config Devices). Set Configure Devices to MUX 16 Duplex or Triplex. Note Do not use MUX 16 posem. 3 To configure the COM port, press the MENU button.
EDVR Menu Map Quick Settings 1. Time Setting 2. Date Setting 3. Title Settings 4. Normal Record Rate 5. Record Quality 6. Disk Full Title Setting Individual Channel-based Settings Sequence Settings 1. 1- Channel Display 1. 2. 3. 4. 5. 6. 7. 8. 9. Display Options Time Mode Time Setting Date Mode Date Setting Time Zone Title Settings Main Monitor Display Call Monitor Display Daylight Saving Setting 1. 2. 3. 4.
1. 2. 3. 4. 5. 6. 7. 8. 9. Alarm Settings Alarm Duration Disk Full Alert Pre-Alarm Alarm Record Rate Alarm Record Mode Alarm Record Quality Sensor Type Alarm Input Link Alarm Out Link 1. 2. 3. 4. Record Settings Record Quality Normal Record Rate Audio Sampling Rate Audio Channel Mode Motion Settings Individual Channel-based Settings 1. Sensitivity 2. Target Zone 3. Track Detect 4. Duration 5. Size Advanced Settings 1. 2. 3. 4. 5. 6. 7. 8. 9.
Settings Record Only Alarmed Cameras Alarm Settings Main Menu > Advanced Settings > Alarm Settings > Alarm Record Mode. On each desired camera set mode value to Exclusive. Alarm Buzzer On/Off The Alarm trigger must also be turned on (see item below). Main Menu > Advanced Settings > Alarm Settings > Alarm Out Link. Highlight Buzzer and then set Sensor, V-Loss or Motion column to Yes or No.
Date/Time Settings General Date/Time Settings Access Protection Quick: Main Menu > Quick Settings > Time, Date. Detail: Main Menu > Display Options > Time Mode, Time Setting, Date Mode, Date Setting Main Menu > Advanced Settings > Operation Lock > Highlight Front Button Lock, RS-232 Lock, Playback Lock, Record Button Lock or Network Lock and set value to On or Off. Daylight Saving Setting Main Menu > Display Options > Daylight Saving Setting. Select Country.
PTZ Cameras and Touch Tracker Search Control EDVR from an ADTT16e CD Search Button A: Menu mode Button B: Play mode Button C: Freeze live video Button D: End Menu/Play Track Ball: Navigate through the menus Up/Down to select Right/Left to activate Search > CD Search Filter Search > Search Filter > Alarm Filter, Date Filter or Time Filter Search List Direct PTZ Camera Control from the Front Panel Up, Down, Left, Right: PAN/TILT Shuttle: Zoom Menu/Enter: Focus Seq/Search: Iris Call: Goto Preset Freeze:
NTSC/PAL Toggle Notes: Hold Up and Pause buttons for a least 3 seconds then follow the on-screen instructions.
