Matrix Keyboard ADTTE Operator’s Manual 8000-2675-02 Rev.
ADTTE Matrix Keyboard Operator’s Manual
Thank you for using American Dynamics products. We support our products through an extensive and worldwide network of dealers. The dealer, through whom you originally purchased this product, is your point of contact if you have a need for service or support. Our dealers are fully empowered to provide the very best in customer service and support. Dealers should contact American Dynamics at (800) 507–6268 or (561) 912-6259 or on the web at www.americandynamics.net.
TABLE OF CONTENTS PREFACE: BEFORE YOU BEGIN............................................................................ V Using This Manual....................................................................................................v Text Conventions .....................................................................................................v Related Documents................................................................................................. vi Support Services ................
NOTES: iv ADTTE Matrix Keyboard Operator's Manual
PREFACE Before You Begin The Operator's Manual explains the features, operation, and application of the ADTTE Touch Tracker matrix keyboard (ADTTE matrix keyboard). It explains the tasks that can be performed when using this product as part of your system. Using This Manual This manual is organized as follows: • • • • • Chapter 1: ADTTE Matrix Keyboard Overview describes the keyboard and its use. It also identifies buttons found on the keypad.
Related Documents Installation of the ADTTE matrix keyboard is covered in the Installation Instructions (part number 8000-2675-01). If you cannot find the answers in this document about performing a specific task with your keyboard, refer to the system operating instructions. The operating instructions provide information about which features, such as satellite sites and user login, the keyboard supports. Keep in mind that some features may not be implemented at your facility.
CHAPTER 1 ADTTE Matrix Keyboard Overview The ADTTE matrix keyboard (Touch Tracker) is a video control station that provides the same functions as the AD2079 System Keyboard. It is compatible with all current models of American Dynamics switches. It allows you to operate cameras installed around your facility. You may also control auxiliaries, such as lights and door locks, if your system is configured with those features.
Keypad Overview 1 2 3 4 5 30 6 29 7 28 8 27 26 9 10 25 11 24 12 13 23 22 21 20 19 1. Site field shows the status of the connected switching system. See the appropriate operating instructions for additional information. 2. Monitor field shows the number of the monitor controlled by the keyboard. 3. Camera field shows the number of the camera controlled by the keyboard. 4. Entry field shows the numbers being entered on the keypad (see item 18). 5.
9. Auxiliary On (PG-Left) / Auxiliary Off (PG-Right) buttons activate and deactivate features such as lights, locks, or alarms that can be controlled by the keyboard. See Chapter 3 for additional information. These buttons also serve as the Page Left and Page Right functions during menu programming. 10. Pswd button sets or changes the keyboard lock password. There are two types of passwords: Permanent and User Defined. See Chapter 2 for specific instructions. 11.
24. Site button controls satellite systems. Refer to the system operating instructions for additional information. 25. Run (↑) / Hold (↓) buttons are used with predefined monitor tours, universal tours, or alarm tours. Run starts a tour. Hold halts the tour. In addition, these buttons serve as the Cursor Up/Down function during menu programming. 26. User button allows authorized users to log on to the system. See the system operating instructions for additional information. 27.
CHAPTER 2 Getting Started This chapter provides an overview of the fields displayed on the LCD. It explains how to determine if the keyboard lock is enabled, as well as providing instructions for locking or unlocking the keyboard. It also explains how to set or change the user-defined password. LCD Display Overview The keyboard display is a 2-line by 16-character backlit LCD (liquid crystal display). It serves the same purpose as the four LED displays on the AD2078 system keyboard.
Understanding the Keyboard Lock Feature The keyboard lock feature prevents unauthorized use of the matrix keyboard advanced features. When “L” appears in the lower right corner of the LCD, operators cannot access certain system features. The features that cannot be accessed are Program Shot, Program Pattern, Mon Arm On, Mon Arm Off, Prog, Menu, and the dual function menu programming keys, such as PG-UP and Enter.
Working with Passwords Passwords allow you to limit access to advanced features of the ADTTE matrix keyboard, such as arming/disarming monitors and the dual function menu programming keys. Passwords may be 1 to 4 digits in length and may be any number between 0-9998. The default password is factory set to 1953. To limit access to the advanced features of the keyboard, change this password using the Pswd button. See Setting or Changing the Password for instructions.
NOTES: 2-4 ADTTE Matrix Keyboard Operator's Manual
CHAPTER 3 Everyday Tasks This chapter describes everyday tasks that users can perform with the matrix keyboard. It explains how to control the zoom, focus, and iris settings for the selected camera. It explains how to program and recall Shots and Patterns to simplify surveillance activities. It also explains procedures for acknowledging alarms and controlling auxiliaries. In This Chapter • • • • • • • • • • Selecting Monitors ...............................................................................
Controlling Cameras Each camera installed at your facility has a unique identification number. To control a camera, you must first select the camera with the matrix keyboard. Then you can control the zoom, focus, iris, pan and tilt of the selected camera. Figure 3-1 identifies the location of the pan/tilt, zoom and focus controls on the matrix keyboard. Figure 3-1: Pan/Tilt, Zoom and Focus Controls Tracker Ball: controls the pan/tilt of the selected camera.
Figure 3-2: Tracker Ball pan/tilt movement. Tilt Up Pan Left Pan Right Tilt Down Moving the Tracker Ball to the right pans the camera to the right. Moving the Tracker Ball to the left pans the camera to the left. Moving the Tracker Ball up or down tilts the camera to the appropriate angle. Simultaneous pan and tilt camera movement can be achieved by moving the Tracker Ball diagonally. Moving the Tracker Ball diagonally up and to the right adjusts the camera up and to the right.
Controlling Zoom and Focus Once you have selected a camera, you can control its zoom and focus settings. Figure 3-4 illustrates the location and function of the zoom and focus buttons: Figure 3-4: Zoom and Focus Controls Zoom In Zoom Out Focus Far Focus Near Adjusting Zoom Settings Zoom refer to the adjustment of the magnification of the camera lens to make an object appear closer (larger) or farther away (smaller). The zoom buttons are located to the left of the Tracker Ball.
Note: Some domes support the resume Auto Iris /Auto Focus command. Press the Iris Open and Iris Close buttons simultaneously to issue the command. The command is available only on domes that support this function. Stepping Through the Cameras Most systems allow you to manually step through the camera entries programmed into the Sequence/Tour (if so programmed) by pressing the Next and Last buttons. Refer to the appropriate operating instructions to determine if this feature is available on your system.
Working with Shots A shot is a programmed video scene, based on a specific pan, tilt, zoom and focus setting that can be recalled automatically. Shots are also referred to as presets or targets. Depending upon your system, you can have multiple pre-defined shots. Refer to the system operating instructions for additional information. Setting Up Shots Note: Shot programming is under keyboard lock protection. Refer to the “Keyboard Lock Feature” in Chapter 2 for information about disabling the keyboard lock.
To display a preset shot: 1. Enter the camera number and press (Camera button). 2. Enter the shot number and press Shot. The camera immediately points to the preset shot, and adjusts zoom and focus automatically. Working with Patterns ! IMPORTANT The procedures discussed in this section are supported by the AD168 Matrix Switcher / Controller System equipped with a Control Code Module (CCM). Other matrix switchers may not support pattern programming in this manner.
Programming Patterns * Tip: Pattern programming is under keyboard lock protection. Refer to the “Keyboard Lock Feature” in Chapter 2 for information about disabling the keyboard lock. You can overwrite an existing pattern using the following procedure. Use caution to ensure that you do not overwrite a pattern that you want to keep. To program a pattern: 1. Enter the camera number and press (Camera button). 2. Pan and tilt the camera to the starting point of the Pattern.
Holding Patterns When you place a pattern on “hold”, you cause the pattern to move to its starting position and wait until you are ready to run it. To hold a pattern, do the following: 1. Enter the monitor number and press show the pattern. (Monitor button). This monitor will 2. Enter the camera number and press whose pattern you want to run. (Camera button) for the camera 3. Enter the pattern number (1-3) and press Pattern. The pattern number (P-1, P-2, or P-3) appears on the LCD. 4. Press Hold.
Running Monitor Tours A monitor tour is a selected sequence of camera video inputs, with selected dwell times, to be displayed on the called monitor. The Prog button is used to define the monitor tour. The Run button is used to initiate the monitor tour. The Prog button is under keyboard lock protection; all users can access the Run button.
Acknowledging Alarms Your system can be configured to handle multiple alarms. Each alarm can be configured to automatically call up video and initiate an auxiliary, such as an audible alarm. In addition, whenever an alarm is triggered, the keyboard beeps, signaling an active alarm. To acknowledge an active alarm, press the Ack button. Continue to press the Ack button until all active alarms have been cleared.
To activate an auxiliary: 1. Enter the auxiliary number. 2. Press Auxiliary On. If this is a momentary auxiliary, you must press Auxiliary On as long as you want the auxiliary activated. To deactivate a latched auxiliary: 1. Enter the auxiliary number. 2. Press Auxiliary Off. Viewing Satellite Sites A site is a complete closed caption television (CCTV) surveillance system, providing both local and remote control of resources within a satellite network.
CHAPTER 4 Utilities and Advanced User Tasks This chapter describes tasks that should only be performed by advanced users of the matrix keyboard. These tasks include setting the language, arming and disarming monitors, displaying the main menu of the switching system, and displaying the firmware version. Many of these tasks are under keyboard lock protection. In This Chapter • • • • • • • • Selecting the Language .........................................................................................
Arming / Disarming Monitors Note: This function can only be performed with the keyboard lock disabled. To disable the keyboard lock, refer to Chapter 2 “Getting Started.” When a monitor is armed, the camera video associated with an alarm for that monitor appears when an alarm has been triggered. To arm a monitor: 1. Enter the monitor number and press (Monitor button). 2. Enter the display/clearance type, and press Mon Arm On.
Displaying the Switching System Main Menu Note: This function can only be performed with the keyboard lock disabled. To disable the keyboard lock, refer to Chapter 2, Getting Started. The Menu button allows you to view the main menu of the attached switching system. When the main menu for the switching system has been displayed, the functions associated with the dual function buttons are enabled. These functions are: • • • • • • • • • • PG-DN displays the next page of menu system.
Displaying the Firmware Version Firmware is the computer instructions programmed into the matrix keyboard. It is unlikely that you will ever need to know the firmware version of the keyboard. However, if you should experience a problem with the keyboard, you may need to provide information about the firmware version. To display the firmware version: 1. Enter 100 and press F1. Firmware information appears on the LCD.
Adjusting LCD Backlighting To adjust the LCD backlighting: 1. Enter 1 and press Config. 2. Use the + and – buttons (located to the right of the LCD) to adjust the backlighting. • Press + to make the LCD backlighting brighter. • Press – to make the LCD backlighting dimmer. 3. When the backlighting is at the preferred level, press Clear to refresh the LCD. Adjusting Key Click Volume To adjust the key click volume: 1. Enter 2 and press Config. 2.
N O T E S : 4-6 ADTTE Matrix Keyboard Operator's Manual
APPENDIX A Software License Agreement 1. General. Software is being licensed to the Customer pursuant to the following terms and conditions, which supplement any purchase or lease agreement (the "Equipment Agreement") between Customer and Sensormatic Electronics Corporation ("SEC"). By accepting receipt of, or by using, such Software, the Customer agrees to be bound by the terms of this Software License Agreement (the "License Agreement").
Customer may make up to 2 copies of the Software solely for back-up and archival purposes. Customer will not remove or modify the copyright and other proprietary notices and legends of SEC and its suppliers contained in the Software and Documentation and will reproduce all such notices and legends on all copies of the Software made by Customer. Customer may not make copies of the Documentation, but may obtain additional copies of the Documentation from SEC at its established rates.
SEC AND ITS SUPPLIERS, EMPLOYEES, AGENTS AND FRANCHISEES WILL IN NO EVENT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR OTHER DIRECT OR INDIRECT DAMAGES (FOR LOSS OF BUSINESS INFORMATION OR PROFITS OR OTHERWISE) SUFFERED BY CUSTOMER, ANY OF ITS EMPLOYEES OR AGENTS OR ANY OTHER PERSON ARISING OUT OF OR IN CONNECTION WITH THE USE OR INABILITY TO USE THE SOFTWARE OR THE DOCUMENTATION, OR THE MAINTENANCE OR SUPPORT THEREOF, EVEN IF THEY HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
N O T E S : A-4 ADTTE Matrix Keyboard Operator's Manual
GLOSSARY alarm The system's response when a camera input changes from its normal state to its abnormal state (if the system has been configured to respond to such a condition). When an alarm is triggered, the keyboard beeps until you acknowledge the alarm via the Ack button. automatic system function A system operation that, once you program it, can be initiated automatically via the matrix keyboard. Shots, monitor tours, and alarms are examples of automatic system functions.
latched auxiliary An auxiliary that remains active until it is deactivated using the appropriate off switch. An example of latched auxiliary is a light. When the Auxiliary On button is pressed, the light is turned on. When the Auxiliary Off button is pressed, the light is turned off. See also auxiliary and momentary auxiliary. LCD Liquid Crystal Display.
INDEX –A– Alarms acknowledging, 3-11 Arming monitors, 4-2 Auxiliaries controlling, 3-11 –B– Backlighting how to adjust, 4-5 Baud Rate setting / changing, 4-4 values supported, 4-4 –C– Camera controlled by Touch Tracker, 2-1 Camera field, 2-1 Cameras controlling, 3-2 focusing, 3-4 iris control, 3-4 locking/unlocking, 3-5 panning and tilting, 3-2 selecting, 3-2 zooming, 3-4 Change password, 2-3 Clearing alarms, 3-11 keyboard lock password, 2-2, 2-3 Keypad, 1-1 LCD display, 1-1 Tracker Ball, 1-1 Firmware, 4
Unlocking cameras, 3-5 Users, 3-12 Utilities arming / disarming monitors, 4-2 baud rate, 4-4 firmware version, 4-4 Index-2 language set up, 4-1 main menu, 4-3 –V– –Z– Zoom button, 3-4 Volume adjusting key click volume, 4-5 ADTTE Matrix Keyboard Operator's Manual
Please visit our website for more information www.americandynamics.net © 2004 Sensormatic Electronics Corporation Product specifications subject to change without notice. Certain product names mentioned herein may be trade names and/or registered trademarks of other companies.
