Advanced Dome Controller ADTT16E Operator’s Manual 8200-0306-02 A1
ADTT16E Advanced Dome Controller Operator’s Manual Version 0701-2833-0103 (EEPROM) 0701-2834-0201 (Flash PROM)
Thank you for using American Dynamics products. We support our products through an extensive and worldwide network of dealers. The dealer, through whom you originally purchased this product, is your point of contact if you have a need for service or support. Our dealers are fully empowered to provide the very best in customer service and support. Dealers should contact American Dynamics at (800) 507–6268 or (561) 912-6259 or on the web at www.americandynamics.net.
TABLE OF CONTENTS PREFACE: BEFORE YOU BEGIN .....................................................................................................................V Using This Manual ...........................................................................................................................................vi Text Conventions.............................................................................................................................................vi Related Documents ...........
N O T E S : iv ADTT16E Advanced Dome Controller Operator's Manual
PREFACE Before You Begin This operator’s manual provides information about the ADTT16E advanced dome controller features and operation. It explains how to use the controller (Touch Tracker) to program and operate the CCTV system. It is designed to be a continuing source of information and reference while using the controller. In This Chapter • • • • Using This Manual................................................................................................................... vi Text Conventions ....
Using This Manual This manual covers the following topics: Chapter 1 Getting Started with the ADTT16E Advanced Dome Controller: Provides an overview of the ADTT16E controller. It explains the different operating modes that may be experienced when using the controller. In addition, it explains how to access and use the controller menus to configure and program your controller.
Notes Special notes appear inside a box similar to this one. The icon represents the information type presented. Special operating notes Tips for operating the system Shortcuts for programming tasks Important system operating information Related Documents Other sources provide supplemental information about using the ADTT16E.These sources serve to enhance your understanding of the system and its applications.
Support Services Various support services are available to help you get the most from your ADTT16E advanced dome controller. • If you have a question about controller operation and cannot find the answer in this manual, consult with your supervisor. • Visit the American Dynamics web site for the latest product documentation and information. The web site address is www.americandynamics.net.
CHAPTER 1 Getting Started with the ADTT16E Advanced Dome Controller This chapter provides an overview of the ADTT16E advanced dome controller. It describes the controller features and explains the different operating modes that may be experienced when using the controller. In addition, it explains where to find additional information for using your system. In This Chapter • • • • • • What is the ADTT16E Advanced Dome Controller? ............................................................
What is the ADTT16E Advanced Dome Controller? The ADTT16E advanced dome controller is a video security system that supports the programming and recall of automated system functions, such as Quick Views, Patterns, and the Controller Sequence. The standard configuration consists of one or two controllers (Touch Trackers), a multiplexer or other video-switching device, monitors, a recording device, and up to 64 domes and fixed cameras. Figure 1-1 illustrates a typical configuration.
Equipment Overview The ADTT16E system consists of controllers, cameras and domes, monitors, a switching device, such as a multiplexer or quad splitter, and recording devices. This equipment is illustrated in Figure 1-1 on page 1-2. Descriptions of the components follow. Advanced Dome Controllers Controllers—also called Touch Trackers— are the system control keyboards used to select the cameras, perform programming and configuration tasks, acknowledge alarms, and run automated system tasks.
System Features The ADTT16E advanced dome controller provides the following features: • Support for up to 64 domes. • Call up video from individual cameras or multiple cameras using a compatible quad splitter or multiplexer. • Control a camera's pan and tilt movements, as well as its zoom, focus, and iris settings. • Run the default SpeedDome pattern, called an Apple Peel, that provides you with complete video coverage of an area.
Controller Features The ADTT16E controller, shown in Figure 1-2, is a video control station that provides easy access to a variety of video control features—from basic camera control to advanced automated functions.
Controller Operating Modes The ADTT16E controller functions differently depending upon the current operating mode. Five operating modes are available: • • • • • Camera control mode Menu/programming mode Sequence mode Alarm mode Quest multiplexer control mode Camera Control Mode Camera control mode is the normal operating mode for the controller. In camera control mode, the currently selected camera number and any running Pattern or Quick View appears on the LCD.
Tip: The A, B, C, and D buttons may also be used in menu/programming mode. The A or B buttons select menu items. C and D buttons scroll through the menu. • • • • A selects the first line on the LCD B selects the second line item on the LCD C scrolls to the previous menu item D scrolls to the next menu item. The following tasks can be performed in menu/programming mode: • Configure system settings: external device, LCD display language, and Primary or Secondary controller.
Alarm Mode The controller automatically goes into alarm mode whenever an alarm is triggered, regardless of the operating mode. When the alarm mode is active, the controller beeps intermittently until the alarm is cleared (either automatically or manually by pressing the Clear button). Alarms are configured using menu/programming mode. When configuring the alarm, you determine what triggers the alarm and what actions occur in response to the alarm.
What To Do Next Now that you have a basic understanding of the ADTT16E advanced dome controller, you can begin using the system.
N O T E S : 1-10 ADTT16E Advanced Dome Controller Operator's Manual
CHAPTER 2 Changing Configuration Settings Before performing other tasks, verify that your ADTT16E advanced dome controller configuration settings are correct. Follow the instructions in this chapter to set the language, configure primary or secondary controller settings, configure the external system, and enable or disable passwords. In This Chapter • • • • Setting the Language for Prompts and Messages.......................................................
Setting the Language for Prompts and Messages English is the initial setting for controller prompts and messages. Change the language setting if you need to display the prompts and messages in another language. The following languages are supported: • • • • English (default) French Spanish German • • • • Dutch Italian Japanese Portuguese • Swedish • Hungarian To change the language setting: 1. Press Menu. 2. Scroll through the menu items until Select Language appears on the LCD.
Setting Up Primary versus Secondary Controllers If two controllers are installed, one must be configured as the Primary Controller, and one must be configured as the Secondary Controller. The Primary Controller interfaces with the multiplexer or other video switching unit. In addition, the Primary Controller can change the display format of the Main Monitor and supports all system programming features.
Changing the Primary/Secondary Controller Setting IMPORTANT If only one controller is installed, it must be configured as the Primary Unit. 1. Press Menu. 2. Scroll through the menu items until Tog Primary/2nd appears on the LCD. Press Zoom or Focus to select. Tip: Zoom selects the first line of the LCD; Focus selects the second line. 3.
Configuring the External System The controllers are capable of interfacing with a number of different external devices. The Primary Controller must be configured to communicate with the correct device for the system to operate correctly. Table 2-2 lists the available settings.
Changing the External Device Setting IMPORTANT Only the Primary Controller can be used to perform this task. 1. Press Menu. 2. Scroll through the menu items until Config Devices appears on the LCD. Press Zoom to select the first line of the LCD, or Focus to select the second line. 3. The LCD displays the current setting. Press Next to display the device types. 4. When the correct device appears on the top line of the LCD, press Menu to save the device setting.
Password Programming Guidelines 1. Do not create passwords that can be easily guessed. Avoid using repeating numbers, such as 1111 or 2222, or sequential numbers, such as 1234 or 9876. 2. Passwords for each privilege level should be distinct. For example, if you set the Administrator password to be 6528, you would not want the Programmer or Operator passwords to be 6527 or 6529. 3. Keep the list of passwords in a secure place. Only permit authorized personnel to access the password list.
Setting the Programmer Password Once the Administrator password is set, assign Programmer and User (Operator) passwords. Programmers can perform all programming tasks documented in this book except setting, changing, or disabling passwords. IMPORTANT You must be logged on as the Administrator to set the Programmer password. 1. Press Menu. 2. Scroll through the menu items until Program Password appears on the LCD. Press Zoom to select the first line of the LCD or Focus to select the second line. 3.
Setting the User Password Users (operators) are restricted from performing any programming tasks. Users can only operate the ADTT16E system, log on or log off the controller, and change the LCD language setting. IMPORTANT You must be logged on as the Administrator to set the User (Operator) password. 1. Press Menu. 2. Scroll through the menu items until User Password appears on the LCD. Press Zoom to select the first line of the LCD or Focus to select the second line. 3. Enter New Pswd appears on the LCD.
Disabling Passwords Disable passwords by setting the Administrator password to “0000” (four zeros). Perform this task on each controller where passwords have been set. 1. Enter the current Administrator password at the Enter Password prompt on the controller. 2. Press Menu. 3. Scroll through the menu items until Admin Password appears on the LCD. Press Zoom to select the first line of the LCD or Focus to select the second line. 4. Enter New Pswd appears on the LCD. Use the number buttons to enter 0000.
CHAPTER 3 Operating the ADTT16E Advanced Dome Controller This chapter explains how to operate the ADTT16E advanced dome controller. It explains how to log on and off the controller if passwords are enabled. It describes how to change the monitor display format, select and control cameras, run automated system functions, and how to activate flip and peel functions for SpeedDome series camera domes. In addition, it explains how to control dome outputs and clear system alarms.
Logging On / Off the ADTT16E Controller If passwords have been programmed for the advanced dome controller, you must log on before attempting to use the system. Passwords are 4-digit codes that restrict access to system functions. Three password levels are available: Administrator, Programmer, and User. The functions available are based upon the password level assigned. • • • Administrators have full system privileges.
Monitor Display Formats Tip: Only the Primary Controller can be used to perform this task. Depending upon the installed switching device, video may be displayed in 2X2 (4 cameras), 3X3 (9 cameras), or 4X4 (16 cameras) format. Video from the selected camera may also be displayed in full-screen format. Note If a Multivision Quest multiplexer is installed, other display formats are available. Refer to Chapter 5 for more information.
Displaying Video with Quad Processors Quad processors provide the ability to see video from up to eight cameras. The video can be viewed from each camera individually, or it can be displayed in quad mode. QUAD DISPLAY MODE Quad display mode allows video from 4 cameras to be displayed at once on the monitor. The camera number appears in the bottom of its respective quadrant on the monitor. Depending upon the model, as many as eight cameras may be connected to your system.
2x2 DISPLAY FORMAT Video displays from 4 cameras when 2x2 format is active. 4-, 9-, and 16-camera multiplexers support this display format. 3x3 DISPLAY FORMAT Video displays from 9 cameras when 3x3 format is active. 9- and 16-camera multiplexers support this display format. 1 2 3 4 5 6 7 8 9 4x4 DISPLAY FORMAT 1 5 Press 2 6 3 7 4 8 9 10 11 12 13 14 15 16 Video displays from 16 cameras when 4x4 format is active. 16-camera multiplexers support this display format.
Selecting and Controlling Cameras Each camera has been assigned a unique number. To select a camera, enter the camera number and press button. (Camera button). Figure 3-2 illustrates the location of the Camera Figure 3-2: Camera button A C B D Peel 1 3 Flip 6 Pattern View Info 4 On Output Menu Off 7 Clear Close Iris Open 5 8 Repeat Pattern 9 0 Previous Next Enter a camera number and press to select a camera. Full-screen video from the selected camera appears on the monitor.
The Primary Controller operator maintains control over the camera until one of the following events occurs: • • • • • A different camera is selected Menu/programming mode is started The Controller Sequence is initiated An alarm comes into the system The selected camera remains idle for 3 minutes Once the Primary Controller operator relinquishes control of a camera, the message, Camera Free appears on the Secondary Controller (if the Call operator has that camera selected).
Controlling a Camera's Pan and Tilt Camera movement can be manually controlled once a camera is selected. Pan is the side-to-side camera movement. Tilt is the up and down camera movement. The Tracker Ball controls the pan and tilt movements. Move the Tracker Ball left and right to pan the camera. Move the Tracker Ball towards you or away from you to tilt the camera. Figure 3-4 illustrates how to control the pan and tilt movements.
Controlling Zoom and Focus Control the zoom and focus settings of the selected camera by pressing the Zoom and Focus buttons. Figure 3-6 illustrates the locations of these buttons. Figure 3-6: Zoom and Focus buttons Zoom In Zoom Out Focus Near Focus Far Zoom refers to adjusting the magnification of the camera lens to make an object appear closer (larger) or more distant (smaller). To make objects appear closer to the camera, press Zoom In.
Controlling the Iris Normally the camera's automatic gain function and the auto/manual iris function control the brightness of the image. However, there may be times when the scene on the monitor could be even darker or brighter. The iris control buttons—Iris Close and Iris Open—regulate the image brightness. Figure 3-7 illustrates the location of the iris control buttons.
SpeedDome Peel and Flip Features The SpeedDome series camera domes support two special features called Apple Peel and Flip. Pressing the appropriate buttons on the controller automatically activate these features. Figure 3-8 illustrates the location of the Peel and Flip buttons. Figure 3-8: Peel and Flip buttons A C B D Peel 1 3 Flip Pattern View Info On Press to run the default SpeedDome pattern.
“Flipping” the SpeedDome A SpeedDome camera dome can rotate 180° from its current pointing direction by pressing the Flip button. This feature is useful when tracking someone who walks directly under the SpeedDome and continues walking on the other side. The message Flip Dome appears on the second line of the LCD when the Flip button is pressed. Cam 16 Flip Dome + Displaying Quick Views Use Quick Views to call up specific scenes from programmable domes, regardless of the current pointing direction.
Running Patterns IMPORTANT The SpeedDome LT supports a feature called “Auto Pan” that allows you to program a smooth side-to-side camera movement for an area. See Chapter 4 for additional information. A Pattern is a sequential series of pan, tilt, zoom, and focus movements from a single camera. You “teach” the camera a combination of these movements. Whenever the Pattern is run, the camera automatically recalls the movements it was taught. Patterns can be run once or run repeatedly until manually stopped.
To run a pattern: 1. Select the camera where the Pattern is saved. 2. Enter the Pattern number, and press a pattern button. Action LCD Information Press Pattern to run the Pattern once. Cam 8 Run Pattern + Pattern finished. Cam 8 Pattern Done + Press Repeat Pattern runs the Pattern indefinitely until manually stopped. Cam 8 + Repeat Pattern Notes If the selected Pattern has been programmed, the Pattern automatically runs. If the Pattern has not been programmed, the default Apple Peel pattern runs.
Running the Controller Sequence Tip: Only the Primary Controller can be used to perform this task. The Controller Sequence consists of a collection of 16 events (Quick Views, Patterns, and fixed shots) from the system cameras. When the Sequence is running, these events are automatically displayed one after the other on the Main monitor. Each event remains on the monitor for a specified duration (from 1 to 90 seconds); each event may have a different duration.
Controlling Dome Outputs Output devices are hardware components connected to dome outputs that can be operated by the controller. Typical output devices include gates, door strikes, and lights. Depending upon the dome type, as many as four output devices may be connected. The output control buttons on the controller activate or deactivate the output devices connected to the currently selected dome. Figure 3-14 illustrates the location of these buttons.
Clearing System Alarms Tip: Only the Primary Controller can be used to perform this task. The ADTT16E advanced dome controller can be configured to handle up to 64 alarms. When an alarm is triggered, it takes precedence over the activity currently being performed on the Main monitor and Primary Controller. For example, if the controller is in programming mode, the alarm information replaces the programming information.
Figure 3-16: Clear button A C B D Peel 1 Flip 3 View Info 4 On Output Menu Off 7 Clear Close Iris Open 5 8 0 6 Pattern Repeat Pattern 9 Previous Next When you clear an alarm, its associated output returns to its original state, and the alarm information is removed from the LCD. Continue to press Clear until all active alarms have been acknowledged. The controller stops beeping after all active alarms are cleared.
CHAPTER 4 Programming Controller Functions This chapter explains how to program the automatic functions for the ADTT16E advanced dome controller. Programming instructions for Quick Views, Patterns, and the Controller Sequence are provided. In addition, system alarm set up is explained. In This Chapter • • • • • Programming Quick Views.................................................................................................... 4-2 Programming Patterns................................................
Programming Quick Views A Quick View is a programmed video scene based on specific pan, tilt, zoom, and focus settings for a programmable dome. Program Quick Views if you need to frequently observe specific locations, such as entrances, lobbies, or loading docks. Presets and Targets are other names used for Quick Views. When accessed, the Quick View automatically calls up the scene for the selected dome, regardless of where the dome is currently pointing.
Programming Patterns A Pattern is a series of pan, tilt, zoom and focus movements from a single programmable dome. Program Patterns if you need to observe large areas at your facility, such as parking lots, warehouses, or long hallways. Tour is another name used for Pattern. Depending on dome type, up to three patterns may be programmed. IMPORTANT If you have SpeedDome LT domes installed, a special pattern called the Auto Pan is available.
Pattern Programming Instructions 1. Select the camera for the Pattern you want to program. 2. Adjust the pan, tilt, zoom and focus settings for the camera until the starting point for the Pattern appears on the monitor. 3. Press Menu. 4. Scroll through the menu until Record Pattern appears on the LCD. Press Zoom or Focus to select. 5. Enter Patrn#? appears on the LCD. Enter the Pattern number (1-3). The following information appears on the LCD: Record Pattern 98 Finish w Available commands 6.
Programming the Controller Sequence Program the Controller Sequence if different locations require regular monitoring. The Sequence is of a collection of 16 events that have been defined for your system's cameras initiated by the Primary Controller. Each event can be a Quick View, Pattern, or fixed shot that displays for a designated period (1 to 90 seconds). When the Sequence is running, the Main monitor displays these events in the programmed order.
The controller keypad is also used during sequence programming. Figure 4-2 illustrates the controller keypad; Table 4-2 describes which keys are used.
Sequence Programming Instructions 1. Press Menu. 2. Scroll through the menu until Define Sequence appears on the LCD. Press Zoom or Focus to select. Information for the first event displays on the LCD. Continue with step 4 to program this event. Otherwise, continue with step 3. 3. Move the Tracker Ball up or down to scroll to the event you want to define. If necessary, press Clear to remove any previously programmed information. 4. Enter the camera number in the Cam field. 5.
Configuring System Alarms Alarms are events that occur automatically in response to external conditions. Input devices, such as smoke detectors or motion sensors, connect to the domes at your facility. Alarms occur whenever input devices change to its abnormal state. This situation places the alarm in a queue, waiting for acknowledgement. Programming alarms helps to provide notification of urgent situations arising at your facility. 64 dome alarms can be configured for the ADTT16E system.
The blinking square on the LCD represents the cursor's location. Move the Tracker Ball up and down to move between inputs for the selected camera. Move the Tracker Ball left and right to move the cursor between the fields. The controller keypad is also used during alarm programming. Figure 4-4 illustrates the controller keypad; Table 4-4 describes which keys are used.
Alarm Programming Instructions Tip: Only the Primary Controller can be used to perform this task. 1. Select the camera requiring alarm programming. 2. Press Menu. 3. Scroll through the menu selections until Alarm Actions is displayed on the LCD. Press Zoom or Focus to select. 4. The information for input 1 appears on the LCD. If this is not the correct input number, use the Tracker Ball to scroll until the correct input number appears. Continue with step 5.
SpeedDome LT Auto Pan Programming The Auto Pan is a special feature supported by SpeedDome LT only. It allows you program a smooth side-to-side camera pan of an area. The SpeedDome LT does not allow you to program the same types of Patterns that other domes support. Instead, use Pattern programming to set the Auto Pan function.
Auto Pan Programming Instructions 1. Select the camera requiring alarm programming. 2. Adjust the pan, tilt, zoom and focus settings for the camera until the starting point for the Pattern appears on the monitor. 3. Press Menu. 4. Scroll through the menu until Record Pattern appears on the LCD. Press Zoom or Focus to select. 5. Enter Patrn#? appears on the LCD. Press number 1. 6. Move the camera until you see ending point for the Auto Pan you are programming.
CHAPTER 5 Quest Multiplexer Support The ADTT16E advanced dome controller provides support for the MultiVision Quest triplex multiplexer. This chapter describes how to use the controller to access the advanced features offered by the Quest triplex multiplexer. These features are not supported with the Quest duplex multiplexer. In This Chapter • • • • • • What is the MultiVision Quest Triplex Multiplexer? ................................................
What is the MultiVision Quest Triplex Multiplexer? The MultiVision Quest triplex multiplexer is a 10- or 16-channel multiplexer that allows viewing of multiple cameras using a single monitor. In addition, the video signals from all camera inputs may be recorded using a single VCR. By connecting two VCRs, you can take advantage of the multiplexer’s triplex features. Triplex operation allows video recording while simultaneously viewing live video (from cameras) and video playback (from the second VCR).
Using the Controller to Access Multiplexer Functions Specific controller keys permit access to the Quest multiplexer functions. Figure 5-1 illustrates the locations of the keys that can be used. Table 5-1 describes the various Controller features used to access the Quest multiplexer functions. Figure 5-1: Controller keys used with multiplexer features.
Changing the Multiplexer Display Format The Quest Multiple offers a variety of display formats not available with other American Dynamics multiplexers. In addition, the order of cameras displayed in the different formats can be manually assigned to suit your surveillance purposes. Press format.
Assigning Cameras to Multiplexer Display Windows 1. Press until the display format you want to change appears on the monitor. 2. Press to start setup mode. The word Set and a highlight box appears on the screen. Figure 5-3: Example multiplexer display programming screen. Selected window SET 3. Use the Tracker Ball to move the highlight box to the window you want to set. 4. Enter the camera number and press to assign the camera to the highlighted window. 5.
Using the Multiplexer Digital Zoom The Quest Multiplexer supports 2x digital zoom for the currently selected camera. This feature is useful if you have fixed cameras installed and cannot otherwise adjust the zoom. If you are currently running the multiplexer sequence, the B (zoom) and D (escape) keys act in the following manner. See Figure 5-4 for details. Figure 5-4: Multiplexer Zoom and Escape function behavior Operating Mode Press B on Controller Seq.
Working with Freeze Frame and Freeze Field Modes The Quest multiplexer supports the ability to freeze the current image on-screen. This is useful if you need to briefly stop the live image to write pertinent information about a situation or zoom into the image. For example, you may want to log license plate numbers for vehicles entering a parking garage. Two freeze modes are available: Freeze Frame and Freeze Field. Freeze Frame is useful for static images with little motion.
3. The highlight appears on the 1 Pages setting. Move the Tracker Ball left or right to change the number of pages displayed (1-16). • Left decreases the number of pages. • Right increases the number of pages. 4. Move the highlight to the 2 Mode setting. Move the Tracker Ball left or right to change the mode. Table 5-2 describes the different modes; Figure 5-2 on page 5-4 illustrates the formats.
CHAPTER 6 Using System Utilities and Solving Problems This chapter provides information about performing utility tasks for the ADTT16E advanced dome controller. It also provides troubleshooting information for problem diagnosis. In This Chapter • • • • What are System Utilities? ......................................................................................... 6-2 Working with Dome Utilities .....................................................................................
What are System Utilities? If you need to perform maintenance on the ADTT16E controller, use the system utilities. System utilities assist you with self-help diagnostics and provide convenience features for system operation. There are two types of utilities available: dome utilities and controller utilities. Dome utilities allow you to perform maintenance functions on the domes installed at your facility.
Displaying Dome Identification Information 1. Select the dome whose information you need to display. 2. Press Menu. 3. Scroll through the menu items until Show Dome Info appears on the LCD. Press Zoom or Focus to select. 4. The dome’s Flash PROM and EEPROM information appear on the LCD: Flash PROM Version F 0701-0147-0101 E 0701-0248-0101 EEPROM Version 5. When finished viewing the dome information, press Menu to resume camera control mode.
Testing Dome/Controller Communications 1. Press Menu. 2. Scroll through the menu items until Ping Dome / TTR appears on the LCD. Press Zoom or Focus to select. 3. The LCD displays the dome communication (ping) test information. Number of ping messages sent Ping Dome Tx=0010 Bad=0000 Number of failed messages 4. Press Next to display the controller ping test information. Number of ping messages sent Ping Other TTR Tx=0006 Bad=0006 Number of failed messages 5. Make note if any of the tests fail.
Figure 6-2: SpeedDome Ultra VII 22x DirectSet Menu 0 1 2 3 4 15 16 17 20 TOGGLE QUICK SET MENU DOME CONFIG MENU AUTO IRIS/AUTO FOCUS FLIP PEEL PATTERN SMOOTH SCAN STEPPED SCAN RANDOM SCAN DOME INFO Figure 6-3: SpeedDome Ultra VII Day/Night DirectSet Menu - Page 1 0 1 2 3 4 10 11 12 13 14 FOCUS TOGGLE QUICK SET MENU DOME CONFIG MENU AUTO IRIS/AUTO FOCUS FLIP PEEL PATTERN NIGHT MODE DAY MODE AUTO DAY/NIGHT MODE WDR ON WDR OFF FAR = next page Figure 6-4: SpeedDome Ultra VII Day/Night DirectSet Menu - Page
DirectSet Command /Menu Item Description * 14+Info: WDR OFF Disables Wide Dynamic Range (WDR). Use this setting when the light level is constant or changes in lighting conditions are gradual. Initiates a smooth scan between the left and right scan limits, starting at the left scan limit. If no scan limits have been set, initiates a smooth 360° clockwise rotation around the dome axis using the current tilt, zoom and focus settings.
Working with Controller Utilities The following topics cover the different controller utilities. Topic Page Number Adjusting LCD Brightness 6-7 Turning Key Click Sound On / Off 6-8 Adjusting Key Click Volume 6-8 Locking or Unlocking the Multiplexer Front Panel 6-8 Changing the Alarm Acknowledgement Setting 6-9 Displaying System Information 6-9 Note: You may also change the language setting, designate Primary or Secondary controller, configure the external device, and set the password.
Turning Key Click Sound On / Off 1. Press Menu. 2. Scroll through the menu items until Key Click On/Off appears on the LCD. Press Zoom or Focus to select. The current key click setting appears on the LCD. Keyclick ON Change w Keyclick OFF Change w 3. Press Next to change the setting. • Keyclick ON indicates that key click sound is enabled. • Keyclick OFF indicates that key click sound is disabled. 4. When finished making changes, press Menu to resume camera control mode.
Changing the Alarm Acknowledgement Setting Tip: Only the Primary Controller can be used to perform this task. The controller is initially set to acknowledge alarms automatically after a 60-second delay. The setting can be changed to manual alarm acknowledgement. 1. Press Menu. 2. Scroll through the menu items until Tog Alarm ACK appears on the LCD. Press Zoom or Focus to select. The current alarm acknowledgement setting appears on the LCD. Auto-Ack Alarm Change w Manual-Ack Alarm Change w 3.
Solving Problems If you experience problems with your ADTT16E advanced dome controller, use this section to identify possible solutions. If these procedures do not solve the problem— or the problem is not listed here—contact your American Dynamics representative for assistance.
Monochrome Video-Switching Unit Problems Problem Description Possible Solution No video on monitor. • Quad display not shown in automatic sequences. • Check that the monitor is powered on and adjusted. Check the camera lens adjustments (iris). Check video connections from camera(s) to the video-switching unit. Check video connections from video-switching unit to the monitor. Verify that the video-switching unit is not in VCR playback mode. Verify that Call output is connected to the monitor.
Multiplexer Live Mode Problems Problem Description Possible Solution All LIVE pictures too bright, too dark, or incorrect color. Some LIVE pictures too dark. • The monitor may not be properly adjusted. Adjust the multiplexer gray bars. • The camera iris may not be correctly adjusted. Adjust the camera iris using a calibrated monitor Multiplexer Tape Mode Problems Problem Description Possible Solution Poor or unstable pictures. • VCR not recording.
Controller Camera Control Problems Problem Description Possible Solution Tracker Ball does not move smoothly or binds or sticks. Erratic or no camera control with controllers. • Check for dust and debris around the Tracker Ball. Remove any foreign matter. • Verify that only one controller is configured as “Primary.” Perform a ping test on the controller and the camera to determine if either is faulty. Replace the faulty unit.
N O T E S : 6-14 ADTT16E Advanced Dome Controller Operator's Manual
APPENDIX A Software License Agreement By using the system software, you accept the terms and conditions of this license agreement. Read this license agreement carefully. SOFTWARE LICENSE AGREEMENT 1. General. Software is being licensed to the Customer pursuant to the following terms and conditions, which supplement any purchase or lease agreement (the "Equipment Agreement") between Customer and Sensormatic Electronics Corporation ("SEC").
5. Use and Copies. Customer may use the Software and Documentation only in conjunction with the other equipment identified in the Equipment Agreement, as part of the access control, closed circuit television or other security system being acquired from SEC and for Customer's internal business purposes. SEC will furnish the Software to Customer solely in object code form. Customer may make up to 2 copies of the Software solely for back-up and archival purposes.
EXCEPT AS SET FORTH IN THIS SECTION 6, SEC DISCLAIMS ANY WARRANTY, EXPRESS OR IMPLIED, WITH RESPECT TO THE SOFTWARE OR THE DOCUMENTATION OR THEIR OPERATION OR USE, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE OR USE. SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES, SO THE ABOVE EXCLUSION DOES NOT APPLY IN SUCH STATES. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
N O T E S : A-4 ADTT16E Advanced Dome Controller Operator's Manual
GLOSSARY 2x2 format Display format available on the Main monitor when using a quad splitter or multiplexer. Video from 4 cameras appears on the monitor at once—2 across and 2 down. 3x3 format Display format available on the Main monitor when using a 9 or 16-channel multiplexer. Video from 9 cameras appears on the monitor at once—3 across and 3 down. 4x4 format Display format available on the Main monitor when using a 16-channel multiplexer.
DirectSet menu A special menu available on SpeedDome Ultra VII and other suitably equipped domes, providing easy access commonly used features. The Info button on the ADTT16E controller is used to display this menu. dome A camera housed inside a plastic dome. The ADTT16E system can be used to control programmable SpeedDome series, SpeedDome Ultra series, and SpeedDome Optima series camera domes.
main monitor The monitor that displays the video that is being controlled by the primary controller. menu programming mode The controller state that allows you to display and select from the menu, program the automatic system functions, indicate which external device your system is connected to, and perform utilities. mode of operation The current operating condition of the controller.
Primary Controller The controller that employs all of he functionality described in this manual. It can perform system programming, initiate automatic functions, clear alarms, and execute all of the utilities. Also called the Main Touch Tracker. primary user The person who is currently using the primary controller. programmable camera A dome, such as the SpeedDome, that can be programmed to perform automatic functions. quad The LCD's abbreviation for “quad processor.
SpeedDome Optima series camera dome A programmable camera that enables security personnel to track a target or survey an area. This camera supports programmable features (presets and patterns), 360° continuous rotation, and has a 16x or 22x optical zoom lens. This dome provides one input and one output. SpeedDome series camera dome Programmable camera dome that enables security personnel to track a target or survey an area.
N O T E S : Glossary-6 ADTT16E Advanced Dome Controller Operator's Manual
INDEX 2x2 display format, 3-5 3x3 display format, 3-5 4x4 display format, 3-5 A Adjustment language, 2-2 primary versus secondary controller, 2-3 Administrator password how to disable, 2-10 how to set, 2-7 ADTT16E Overview, 1-2 Alarms clearing automatically, 3-17 setting up, 4-8 Apple Peel pattern, 3-11 Auto Pan feature SpeedDome LT, 4-11 automatic alarm acknowledgment, 3-17 C Cameras iris control, 3-10 pan/tilt, 3-8 resolving control conflicts, 3-6 stepping through, 3-7 zoom/focus, 3-9 Controller accessi
Disabling All, 2-10 overview, 2-6 Programmer, 2-8 programming tips, 2-7 User/Operator, 2-9 Patterns Apple Peel, 3-11 defining, 4-3 Programmer password how to set, 2-8 Programming Time Saver Patterns, 4-4 Quick Views, 4-2 Sequence, 4-7 Q Quad splitter, 2-5 quad splitters, 3-4 Quest Multiplexer accessing functions using Controller, 5-3 assigning cameras to windows, 5-5 Index-2 available display formats, 5-4 Description, 5-2 freeze frame/freeze field, 5-7 program sequence, 5-7 sequence, 5-7 using digital zo
Please visit our website for more information www.americandynamics.net © 2004 Sensormatic Electronics Corporation Product specifications subject to change without notice. Certain product names mentioned herein may be trade names and/or registered trademarks of other companies.
